Nikon PD200 Double Push Button with Leds and Comfort Sensors User Manual

Nikon PD200 Double Push Button with Leds and Comfort Sensors

Product Information

Specifications

• Product Name: Double Push Button with LEDs and Comfort Sensors
• Compatibility : Niko Home Control
• Colour: Piano Black Coated
• Model Number : 200-52202
• Features: Easy click-on mechanism, wall-mounted bus wiring controls, LEDs, comfort sensors

Product Usage Instructions

Installation:

To install the double push button, follow these steps:

• Turn off the power supply to the installation area.
• Mount the double push button on the wall using appropriate screws.
• Connect the wiring controls according to the provided diagram.
• Turn on the power supply and test the functionality.

Operation:

To use the double push button:

• Press the buttons to activate/control the connected devices.
• Observe the LEDs for status indication.
• Utilize the comfort sensors for enhanced control and automation.

FAQ

• Q : Is this product suitable for outdoor use?
• A : No, this double push button is designed for indoor use only.
• Q : Can I integrate this with other Niko Home Control products?
• A : Yes, this double push button is compatible with all Niko finishings and can be integrated into your existing Niko Home Control system.
• Q: How do I reset the comfort sensors?
• A: To reset the comfort sensors, refer to the user manual for specific instructions or contact customer support for assistance.

INTRODUCTION

This double push button can be configured to control a variety of actions and routines in a Niko Home Control II installation on bus wiring. It is fitted with programmable LEDs that provide (inverted) feedback on the action that is being performed. In addition, the push button can serve as an orientation light when the LEDs are ON. Thanks to its integrated temperature and humidity sensor, the push button also supports multi-zone climate and ventilation control, allowing you to increase your energy efficiency and overall comfort.

• Its multi-purpose temperature sensor can be set to control a heating/cooling zone within a Niko Home Control II installation, as a basic thermometer or to create certain conditions (e.g. control sunscreens)
• The humidity sensor can also be used within routines. For example, to perform automatic ventilation control in a bathroom or toilet The double push button features an easy click-on mechanism for wall-mounted bus wiring controls and is available in all Niko finishings

Technical data

Double push button with LEDs and comfort sensors for Niko Home Control, piano black coated.

• Function:
• When using the push button’s temperature sensor for heating/cooling zone control, make sure the room temperature can be measured accurately by eliminating as many factors as possible that may inhibit the thermostat’s ability to accurately control the room temperature.
• When used as a thermostat, DO NOT mount the push button:
  • in direct sunlight
  • on an exterior wall
  • within the immediate vicinity of a heat-generating source (heater, radiator, etc.) or electrical equipment that may radiate heat (TV, computer, etc.).
  • behind a curtain
• Select the push button that best suits the above conditions to control your heating/cooling zone
• Do not allow air to circulate behind the push button. If needed, use an airtight wall-mounting box or fill in any gaps in the flush-mounting box or bus cable duct using PU foam
• Combine the push button’s temperature sensor with a heating or cooling module multizone control or a switching module for electrical heating
• Combine its integrated humidity sensor with a ventilation module to perform automatic ventilation control
• Setpoints and week programmes are managed via the app
• Calibration is managed via the programming software
• Maximum number of push buttons set as a temperature sensor per installation: 20
• Temperature sensor range: 0 – 40°C
• Temperature sensor accuracy: ± 0.5°C
• Humidity sensor range: 0 – 100 % RH (non-condensing, nor icing)
• Humidity sensor accuracy: ±5 %, between 20 – 80 % RH at 25 °C
• Complies with the European standards EN 60669-2-1, EN 63044-3, EN 63044-5-2
• Material central plate: The central plate is enamelled and made of rigid PC and ASA.
• Colour: enamelled Bakelite®-look piano black (approximately NCS S 9000 N, RAL 9005). Bakelite® is a registered trademark of Hexion GmbH
• Fire safety
  • The plastic parts of the central plate are self-extinguishing (comply with a filament test of 650°C)
  •  The plastic parts of the central plate are halogen-free.
• Input voltage: 26 Vdc (SELV, safety extra-low voltage)
• Dismantling: To dismount simply pull the push button off the wall-mounted printed circuit board.
• Impact resistance: After mounting, an impact resistance of IK06 is guaranteed.
• Dimensions (HxWxD): 44.5 x 44.5 x 8.6 mm
• Marking: CE

www.niko.eu

References

• Niko - home automation, switches, socket outlets and detector

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>