thermokon JOY 5DO Digital Room Thermostat User Manual
- June 17, 2024
- thermokon
Table of Contents
- JOY 5DO Digital Room Thermostat
- » APPLICATION
- » SECURITY ADVICE – CAUTION
- » MOUNTING ADVISE ROOM SENSORS
- » TECHNICAL DATA
- » FUNCTION DESCRIPTION – CONTROLLER/FAN STAGES
- » DISPLAY
- » FUNCTION DESCRIPTION – BUTTONS
- » DIAGNOSTICS MENU
- » CONNECTION PLAN
- » DIMENSIONS (MM)
- » ACCESSORIES (OPTIONAL)
- Documents / Resources
JOY 5DO | EC AO2DO | EC 3AO
Fancoil Regulator (from Version 2.6.x)
JOY 5DO Digital Room Thermostat
Datasheet
Subject to technical alteration
Issue date: 22.06.2023 • A126
» APPLICATION
JOY Fancoil 5DO (85..260 V ~)
Modern design, flush mounting fan coil room thermostat. Used for individual
control of temperature in commercial and residential buildings. It is tailored
for two-pipe and four-pipe fan coil units with two-wire electric valves. The
device combines a modern design with a 2,5” LCD and a touchsensitive surface,
3 time program options each with 4 time periods options.
JOY Fancoil EC AO2DO (85..260 V ~)
Modern fan coil room thermostat to control fan coil units with EC fans. It is
suitable for 2- and 4-pipe systems. It has 2 relays and 1 analogue output
0-10V (heating valve, cooling valve and EC fan). The device combines a modern
design with a 2,5” LCD and a touch-sensitive surface, 3 time program options
each with 4 time periods options.
JOY Fancoil EC 3AO (24 V ~/=)
Modern design, flush mounting fan coil room thermostat. Used for individual
control of temperature in commercial, industrial and residential buildings. It
is tailored for two-pipe and four-pipe fan coil units with two-wire electric
valves or controlling a 6-way valve. The device combines a modern design with
a 2,5” LCD and a touch-sensitive surface, 3 time program options each with 4
time periods options.
» SECURITY ADVICE – CAUTION
The installation and assembly of electrical equipment should only be performed
by authorized personnel.
he product should only be used for the intended application. Unauthorised
modifications are prohibited! The product must not be used in relation with
any equipment that in case of a failure may threaten, directly or indirectly,
human health or life or result in danger to human beings, animals or assets.
Ensure all power is disconnected before installing. Do not connect to
live/operating equipment.
CAUTION! Risk of electric shock due to live components within the
enclosure, especially devices with mains voltage supply (usually between
90..265 V).
Please comply with
- Local laws, health & safety regulations, technical standards and regulations
- Condition of the device at the time of installation, to ensure safe installation
- This data sheet and installation manual
» PRODUCT TESTING AND CERTIFICATION
Declaration of conformity
The declaration of conformity of the products can be found on our website
https://www.thermokon.de/
» NOTES ON DISPOSAL
As a component of a large-scale fixed installation, Thermokon products are
intended to be used permanently as part of a building or a structure at a pre-
defined and dedicated location, hence the Waste Electrical and Electronic Act
(WEEE) is not applicable. However, most of the products may contain valuable
materials that should be recycled and not disposed of as domestic waste.
Please note the relevant regulations for local disposal.
» MOUNTING ADVISE ROOM SENSORS
The Accuracy of the room sensors are influenced by the technical specifications as well as the positioning and the installation type.
During Assembly:
- Seal mounting box (if present).
- Installation type, air draught, heat source, radiation heat or direct sunlight can affect the measurement.
- Bulding material specific properties of the installation place (brick-, concrete-, partition wall, cavity wall, …) can affect the measurement. (e.g.: Concrete accepts room temperature variation slower than cavity walls)
Assembly not recommendet in…
- Air draught (e.g.: close to windows / doors / fans …)
- Near heating sources,
- Direct sunlight
- Niches / between furniture / …
» MOUNTING ADVICE JOY
Plasterboard boxes shall be covered by wall paper or paint to avoid that the
plasterboard box’s front rim will be partially visible underneath JOY.
Maybe consider using white plasterboard boxes (i.e. Kaiser 9063-77).
» APPLICATION NOTICE
Software| Software-description on https://www.thermokon.de/
---|---
MicroSD-Card| Data storage device for Update, Upgrade or configuration
– FAT-filesystem required
– NTFS and exFAT filesystems are not supported!
Bootloader| A MicroSD-card Bootloader for loading applications (Update,
Upgrade) or configurations is integrated in the device.
active bootlader = ring illumination blinks (1 sec. cycle), display is not
triggered!
Firmware Update| – Remove upper part, insert a microSD-card with valid Update
file, mount upper part.
– Valid update file is recognized and the update process is started (ring
illumination blinks in a 300ms cycle)
– New application is started automatically after Update (approx. 20-30 sec.).
– Remove upper part, to remove MicroSD-card from the device!
Device Configuration| – Remove upper part, insert a microSD-card with device
configuration file, mount upper part.
– Configuration file is recognized and the device is configured.
– Device ready for operation.
– Remove upper part, to remove MicroSD-card from the device!
The parameters for the display, set point and the controller can only be changed via the configuration software.
» NOTES ON THE UPDATE FUNCTION
An update of the device software is only possible within the version main
numbers.
» CONFIGURATION VIA UCONFIG | MICRO SD-CARD
Configuration software:
uConfig | Windows 10 is required to use the uConfig configuration software
The JOY room thermostat can be parameterised using the uConfig configuration
software. An SD card is used to transfer the created configuration file to the
device.
The installer for the configuration software can be found in the Download-
Section on our website. The installer retrieves all necessary files and plug-
ins from our web server. In this version an update function is integrated in
the software.
Download-Section
» TECHNICAL DATA
» JOY Fancoil 5DO | JOY Fancoil EC AO2DO | JOY Fancoil EC 3AO
Measuring values | temperature, humidity (optional) |
---|---|
Measuring range temp. | 0..+50 °C |
Accuracy temperature | ±1 K (typ. bei 21 °C) |
Measuring range humidity
(optional)| 0..100% rH non-condensing
Accuracy humidity
(optional)| ±2% between 10..90% rH (typ. at 21 °C)
Control function| setpoint adjustment +0..+50 °C, fan stages
Display| LCD 2,5“, 240×160 px, white backlighting
Functions| integrated PI- and 2-point-/ 3-point-controllers, 2nd control
loop: 2-point controller
Enclosure| PC and glass, optional black or white
Protection| IP30 according to EN 60529
Connection electrical| Terminal 1..8
terminal block max. 1,5 mm²| Terminal 9..12
terminal block max. 1.0 mm²
Ambient condition| 0..+50 °C, max. 85% rH non-condensing
Weight| 195 g
Mounting| flush mounted with standard EU box (Ø=60 mm)
» JOY Fancoil 5DO
Output switch contact| 3x normally open contacts (fan speed), 240 V,
load max. 3 A| 2x normally open contacts (heating/cooling), 240 V, load max.
500 mA
Power supply| 85..260 V ~
Power consumption| max. 2,5 VA (260 V ~)
Inputs| DI1
input for NTC 10 K or floating contact| DI2
digital input for non-floating contact (230 V ~)| DI3
digital input for floating contact
» JOY Fancoil EC AO2DO
Output voltage| 1x 0..10 V, max. load 5 mA, EC FAN control
Output switch contact| 2x normally open contacts (heating/cooling), 240
V max. load 500 mA
Power supply| 85..260 V ~
Power consumption| max. 3 VA (260 V ~)
Inputs| DI1
input for NTC 10 K or floating contact| DI2
digital input for non-floating contact (230 V ~)| DI3
digital input for floating contact
» JOY Fancoil EC 3AO
Output voltage| 3x 0..10 V, max. load 5 mA, EC Fan control, heating &
cooling or control 6-way valves (configurable via Software)
Power supply| 24 V = (±10%) oder 24 V ~ (±10%) SELV
Power consumption| max. 2,5 W (24 V =)
Inputs| DI1
input for NTC 10 K or floating contact| Di 2 | DI 3
2 digital inputs for non-floating contact
» FUNCTION DESCRIPTION – CONTROLLER/FAN STAGES
JOY Fancoil 5DO (85..260 V ~)| JOY Fancoil EC AO2DO (85..260 V ~)|
JOY Fancoil EC 3AO (24 V ~/=)
---|---|---
PI controller (PWM) & 2-point/3-point controller
(configurable)| PI controller (PWM) & 2-point/3-point controller
(configurable)| PI controller (0..10 V)
Fan stages (all types)
In automatic mode the fan speed is linked to the controller. The assignment of
the fan stage to the control (heating / cooling, only heating, only cooling)
is freely selectable. To ensure that the fan motor starts reliably, a period
of time can be configured in which the fan starts with maximal value. Using
one or more time channels, the fan control have to be set per timechannel and
per period. Via the touch surface the user has the option to override the
settings of the device every time. When the next time channel starts, the fan
speed is set to the configured value. The fan is set to automatic mode when
the user changes the occupancy state (occupied ↔unoccupied).
Heating/ cooling with PI-controller (PWM) (only 5DO and EC AO2DO)
The time response of the PI control loop depends on the control parameters xp
for the proportional area and tn for the reset time of the integral range. In
case of an error, the P portion immediately changes the position value
proportionally to the error variable, while the integral portion takes effect
after a certain time.
The resulting actuating variable is output as a pulse-width-modulated signal
directly to the outputs.
Heating/ cooling with 2-point-/ 3-point-controller (only 5DO and EC
AO2DO)
In the case of temperature control, the 2-point controller only knows the
switching states heating ON and heating OFF. The 3-point controller also knows
the switching state of cooling. Two – and three-point controller work with a
hysteresis.
Heating/ cooling with PI-controller (0..10 V) (only EC 3AO and EC AO2DO)
The time response of the PI control loop depends on the control parameters xp
for the proportional area and tn for the reset time of the integral range. In
case of an error variable, the P portion immediately changes the position
value proportionally to the error variable, while the integral portion takes
effect after a certain time.
The resulting manipulated variable is output as an analogue 0..10 V signal
directly to the outputs.
EC Fan automatic mode with PI-controller (only EC 3AO and EC AO2DO)
(for EC AO2DO with two-point/three-point controller, the temperature range for
controlling the 0..10 V EC fan is parameterised separately)
The 0..10 V (0..100%) control of the fan is proportional to the calculated
manipulated variable of the PI controller.
example: Calculated actuating variable 65% = Fan control with 6,5 V Calculated
actuating variable 22% = Fan control with 2,2 V
EC Fan manual with PI-controller (only EC 3AO and EC AO2DO)
Up to 5 steps (stages) can be set using the configuration software. The set
number is divided linearly to the manipulated variable of 0..100%.
example: max. steps (stages) = 5
Stage 1 = 20% Stage 2 = 40% Stage 3 = 60% Stage 4 = 80% Stage 5 = 100%| max.
steps (stages) = 3
Stage 1 = 33% Stage 2 = 66% Stage 3 = 100%
---|---
» DISPLAY
| Value Screen
internal sensor values external sensor values configurable)
(additional humidity value optionally configurable)|
---|---|---
| Header (value/ symbol display)
Time, weekday, date, ECO symbol (mode dependent)
Alarm symbol (higher priority than ECO-Symbol)|
| Footer (symbol display)
Symbols for heating/cooling mode, occupancy, window contact, etc.
The symbol „Timechannel active“ is only shown when a time channel is active.|
» FUNCTION DESCRIPTION – BUTTONS
On the touch surface, there are adjustment options for setpoint and fan speed
regulation.
While pressing these buttons, the white ring-LED of the Power-button lights up
for visual feedback.
Fan speed adjustment: „fan speed
up“ / „fan speed down“| Setpoint change (setpoint range
± 3 °C, default, configurable).| Power button for Standbymode,
or Presence key| If the key is used as a
presence key at the same time,
the key must be pressed for at
least 3s, in all other cases a
short press is sufficient.
---|---|---|---
| |
3 seconds without any interaction, the display returns back to main screen.
Standby mode (not compatible with Keycard-switch function)
In standby mode the display and all outputs are switched off (controller
deactivated). The frost and heat protection monitoring remains active.
Navigation Parametermenu
(up, down, left, right)| Open submenu (right)
In header left to leave the submenu| Confirmation
---|---|---
| |
» DIAGNOSTICS MENU
To access the diagnostics menu, select the header in the startscreen of the parameter menu, and press the ENTER key. Here you will find various information, such as device type, software version, state of the inputs and outputs and controller state (current manipulated variable).
» CONFIGURATION
» Parametermenu
| Access to Parametermenu:
Press buttons for 3 seconds simultaneously
---|---
If no entry is made for 8 minutes, the parameter menu is left automatically.
» MENU → TIME CHANNELS
In the Time Channels menu, setpoint and timer can be set. Up to 3 time
channels with 4 time periods each can be parameterized. The time channels are
prioritised. Channel 3 has the highest priority. After selecting the line of
the time channel to be edited, the next submenu is called up with the “Right”
key. It is possible to set any time period within one week in the first two
lines with the “Left” (-)/ “Right”(+) keys. In addition, the ECO mode is
available in the menu sections. In ECO mode, the dead zone between heating
and cooling is automatically set to the ECO dead zone configured in the
“General Settings” menu (default: 10 K).
» MENU → INPUTS
Up to 3 inputs are configurable for functions such as windows contact, dew
point, occupancy, change-over or external sensor option.
The overview of possible combinations can be found in the software
specification of the JOY.
Sensor (NTC10K| The value of an external sensor will be shown if connected and
configured accordingly. In this case, the room thermostat controls according
to the external sensor. Alternatively, an external temperature sensor can be
used at the universal input to protect floor heating. If a configured
temperature is exceeded, the heating sequence is suspended.
---|---
Change-Over DI| Which controller is active depends on the state of the Change-
Over contact. (Factory default: contact open heating controller active,
contact closed cooling controller active). The terminals 4 and 5 are used as
outputs for heating rsp. cooling.
Change-Over Sensor| The Change-Over Sensor is used for switching between
heating and cooling mode automatically. If the temperature is below 22 ° C,
the controller is in cooling mode. If it is above 25 ° C, it is a heating
mode.
If an input is configured as a change-over, the room thermostat is
automatically in 2-pipe operating mode and both outputs (terminals 4 and 5)
are used as outputs for heating rsp. cooling.
Window contact/Energyhold off| If a window contact is enabled via the digital
input, the reference will switch to a setback set point (Heat SP/Cool SP).
Dewpoint| An active dewpoint contact locks the cooling controller.
Occupancy| If occupancy-function is active, the symbol will be displayed
automatically. In state of “unoccupied” the heating set point is reduced by
2K (default setting) rsp. the cooling set point raised by 2K.
Keycard-Switch| When the card is not inserted, the device is switched in sleep
mode. Operation of the keys is locked, the display is switched off and the
controller adjusts to the nominal values of the “unoccupied”-State.
Alarm contact| An alarm symbol can be shown in the header of the display. The
backlight flashes when the alarm is active. This symbol is in the same
position as the ECO symbol. The alarm symbol has a higher priority and
overwrites the ECO symbol!
» MENU → TIME/DATE
Time, Date and display format can be configured in the menu settings. The room
thermostat is equipped with a real-time clock so that it automatically adjusts
for daylight-saving time. This function can be disabled in the datetime
settings.
» MENU → SENSOR SETTINGS
Offset correction for internal and external sensor value.
The temperature display can also be changed from °C to °F.
» MENU → COMMON SETTINGS
Common device settings:
Brightness
Valve protection
ECO deadband
Fanstages (5DO only)
Language
Factory setting (reset)
Brightness
Configuration of the LCD brightness/ LED ring brightness during button
operation/ usage.
Valve protection
A valve protection function actuates the heating and cooling valves regularly
to prevent locking during non-usage times.
The function is executed fridays at 11.00 (heating valve) and 11.15 (cooling
valve). The corresponding valve is triggered for 5 minutes, if not activated
during the last 96 hours.
ECO deadband
The dead band can be adjusted (default 10.0 K)
- further information in the software specification file
Factory setting
By selecting “Factory setting”, the room thermostat will be reset and restore
the device to factory default settings.
» CONNECTION PLAN
JOY Fancoil 5DO (85..260 V ~)
| JOY Fancoil EC AO2DO (85..260 V ~)
| JOY Fancoil EC 3AO (24 V ~/=)
---|---|---
1 Fan Speed 3
2 Fan Speed 2
3 Fan Speed 1
4 Cooling
5 Heating
6 Digitaler Input 2 (230 V)
7 L
8 N
12 GND DI 3
11 Digital Input 3
10 GND DI 1
9 Digital Input 1 (or NTC10K)| 1 EC Fan GND
2 EC Fan (0..10 V)
4 Cooling
5 Heating
6 Digital Input 2 (230V)
7 L
8 N
12 GND DI 3
11 Digital Input 3
10 GND DI 1
9 Digital Input 1 (or NTC10K)| 1 Digital Input 2
2 EC Fan (0..10 V)
3 Cooling (0..10 V) or 6-way valve
4 Heating (0..10 V) or 6-way valve
5 GND DI 2
6 GND
7 24 V = (±10%) or 24 V ~ (±10%)
8 GND
12 GND DI 3
11 Digital Input 3
10 GND DI 1
9 Digital Input 1 (or NTC10K)
Note: Parallel connection of the potential-loaded inputs is not
permitted!
If the operating mode (change-over DI) of several devices is to be switched
together by one contact, the potential-free 230V input must be used (DI2, only
possible with the 230V version). It must be ensured that the same phase is
used for jointly switched devices.
» DIMENSIONS (MM)
» ACCESSORIES (OPTIONAL)
Frame for surface mounting JOY pure white | Item No. 760201 |
---|---|
Frame for surface mounting JOY black | Item No. 760951 |
Decorative frame pure white for JOY | Item No. 681452 |
Decorative frame black for JOY | Item No. 740951 |
MicroSD card 2GB | Item No. 500098 |
Thermokon Sensortechnik GmbH, Platanenweg 1, 35756 Mittenaar, Germany ·
tel: +49 2778 6960-0 ·
fax:-400 ·www.thermokon.com ·
email@thermokon.com
JOY_Fancoil_Datasheet_en © 2023
Documents / Resources
|
thermokon JOY 5DO Digital Room
Thermostat
[pdf] User Manual
JOY 5DO Digital Room Thermostat, JOY 5DO, Digital Room Thermostat, Room
Thermostat, Thermostat
---|---
References
- Thermokon – Home of Sensor Technology
- Thermokon – Home of Sensor Technology
- Thermokon – Home of Sensor Technology
- Downloads – Produktinformationen, Software und Medien
- Downloads – Produktinformationen, Software und Medien
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>