MEETDUMPL QW0000000 Mini Heat Press Instructions

June 17, 2024
MEETDUMPL

MEETDUMPL QW0000000 Mini Heat Press Instructions
MEETDUMPL QW0000000 Mini Heat Press

Be sure to check the Safety Instructions before use

SAFETY INSTRUCTIONS

  • This product is an electrical product, and safety precautions should be followed to avoid accidents.
  • In order to prevent electric shock accident, the machine must be connected to a correctly grounded socket, and the correct voltage must be selected to ensure correct grounding. It is not allowed to be exposed to rain or humid environment. When not in use, please disconnect the power supply. After the machine is completely cooled, it can be stored in a suitable place.
  • This device is not intended to be used by persons (including children) with physical, sensory, or mental impairments or lack of experience and knowledge, unless they are supervised and instructed by those responsible for their safety.
  • If the power cord or the machine is damaged, it must be replaced and repaired by the manufacturer or authorized service agent to avoid danger.
  • It is strictly forbidden to use this equipment in a humid and corrosive environment, and do not use this equipment in a combustible or explosive environment. After the machine is turned on, someone needs to take care of it to ensure safe operation.
  • When replacing product parts, please use original accessories.
  • This product complies with CE, FCC, ROSH and other certifications, and has applied for an industry patent, and counterfeiting must be investigated.

The new upgrade

New upgrade

Data

Input voltage(V) AC110V(US) / AC220V(EU)
Rated Power(W) 200W
Temperature Range Mode 1(284℉)/ Mode 2(320℉)/ Mode 3(374℉)

Operate

  1. Turn on the machine: press and hold the power button for 3 seconds to turn on the machine, and the default mode 1 is automatically turned on for heating. (Refer to the following mode parameters)
    If you have already used it, and the machine automatically shuts down after the last use, then the machine will enter the heating mode set last time when it is turned on.
    Operate

  2. Mode switching: After turning on the machine, press and hold the power button again for 3 seconds to switch to other modes, and each time you press it, you can switch to a mode. There are 3 modes for you to choose:
    Mode 1 (Slightly bright): 284℉
    Mode 2 (Normal): 320℉
    Mode 3 (Super bright): 374℉
    Operate

  3. After the mode is selected, machine will heat automatically. When the light flashes, it means that it is heating; when the light stays on, it means that the machine has reached the required temperature, and the heat pressing can be started.

  4. Before starting the heat pressing, put the hat on the silicone pad, and fix logo sticker to be pressed on the hat with high-temperature tape.
    Operate

  5. Then start heat pressing, and it will be done in about 8-16 seconds. Finally, wait for the logo pattern to cool off, and slowly tear off the transfer paper.
    Operate

  6. Machine shutdown: After mode 3, press and hold the power button again for 3 seconds to shut down. The heat press machine will automatically shut of if not used for 15 minutes.
    Operate

NOTE

  1. Try to keep the surface of the product as smooth as possible. The material of some hats/clothes is relatively rough, so that the contact of the heating surface is not enough, resulting in weakened hot stamping effect.
  2. Heat pressing time, 8-16 seconds is recommended, adjust the heat pressing time and manual pressing pressure according to the actual effect.
  3. The principle of thermal transfer printing is to precisely transfer the pattern to the surface of the product by heating and pressing to complete the product printing
  4. After the heat pressing is completed, according to the characteristics of the transfer paper, the temperature of the transfer paper should drop to room temperature before tearing of the transfer paper.

QA

Q: What should I do if the transferred pattern is too dark/light?

A: The higher the temperature and the longer the time, the darker the transferred pattern; you can adjust it according to the actual situation.

(2). Q: After heat pressing, the temperature of the transfer paper also

dropped. Why did the transfer fail when the transfer paper was torn off?

A: It may be that the surface of the hat is relatively rough, resulting in insufficient temperature contact during the hot-stamping process. In the area where the transfer failed, it can be hot stamped again, and the down pressure of the hot stamp can be manually increased to ensure that the temperature of the contact surface is sufficient.

DISCLAIMER

  1. This product is not suitable for children.
  2. The pictures of this product are all taken in kind. Due to the influence of light and angle during the shooting process, including the color difference of the display resolution, the products of distribution channels in different regions will be slightly different, and the products displayed in the mall shall prevail.
  3. The manufacturer’s packaging pattern will change without notice, and the store pictures will be updated as much as possible to ensure the latest product types.
  4. The internal circuit of this product is disassembled without permission, and the components that are not of our company are replaced, resulting in product damage, and our company is not responsible for it.
  5. For all products sold, the company first requires that on the premise of strictly using assembly and necessary technology, we are only responsible for the after- sales of the product (the purchased product itself) (when repaired or replaced) The manufacturer confirms that it is a quality problem, The company is not responsible for any other loss and injury.
  6. As a compliant manufacturer, we design, manufacture and sell without any propaganda meaning of politics, military, religion, country, race or color. What manufacturers can do is to respect scientific, historical rules as much as possible. The purpose of the manufacturer is for the peace of mankind.
  7. For other unresolved matters, it shall be implemented in accordance with relevant national laws and regulations!

Warranty Terms:

  1. The table for feedback from customers should be returned to our company within a month after the date of purchase. In this way, customers may enjoy one- month repair warranty.
  2. Repair Warranty and Purchase Certificate should be presented. The warranty only applies when all the required documents are available.
  3. The warranty does not apply when the equipment has received damage through abuse, carelessness, improper installation, accident or mishandling during shipment, connecting to improper line voltage, or has been serviced by anyone other than an authorized factory representative.
  4. After the warranty period, we are ready to provide charged repair service, perfect as always.

Dear Sir/Madam:
Thank you for purchasing our products. To improve our service and ensure the proper use of our products, please kindly write down your suggestions.
Name of Product:
Date of Purchase:
Your Suggestions:
Package:
Functions:
Others:
Date:

GUARANTEE CARD

The product conforms to the technical standards
QC.
Manufacture Date
Fast To Buy Limited

GUARANTEE CARD

The warranty is valid in one year since the purchase of this any quality problem found please send back to us with courier fee to be collected upon receipt of the returning unit, we will repair it and send back to customer within two working days.
Notice Please enclose the warranty card along with the returning product, or else we have the right to reject the repairing thanks for your corporation.
Company logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals