OTTO WILDE Otto Lite 800°C Griller Kit Instruction Manual

THE OTTO GRILL
LITE

Otto Lite 800°C Griller Kit

BE SURE TO READ BEFORE USING!
Keep this manual for future reference
STARTS ON PAGE 4

OPERATING MANUAL (US)
This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. Please read and follow all warnings and instructions before assembling and using the appliance.

WELCOME TO THE FAMILY!

FIIINALLY, BUDDY!
There’s the thing! Otto Wilde congratulates you on the purchase of your Otto Grill Lite. That was a damn good decision, because it’s the only way to grill the steaks you really deserve. From today on you belong to the big grill family of Otto Wilde. We wish you great barbecue experiences and lots of fun with your new Otto  Grill Lite! Otto, Alex, Julia und Nils.
GRILLING SAFELY!
Of course you would like to start grilling right now and have your first steak sizzling on the grill grate. But before you get to the festive grilling, you should take a close look at our manual. This increases your anticipation and guarantees safe grilling pleasure. In our instructions for use, we show you how to use the concentrated power of the Otto Grill Lite responsibly. Should you lend out your grill, this manual should be part of the package. And now, you can fire up the grill – because only after reading is it time to grill some steaks!!

PEOPLE WHO READ LIVE LONGER

WARNING NOTES

The Otto Grill Lite is a really hot device reaching really high temperatures (1500 °F / 815 °C). As a high-temperature griller, you have to master the grill and the grill process well. That’s why we’ve put together important information for you on how to use the Otto Grill Lite safely. Please read this carefully, as failure to comply with the hazard warnings and precautions listed here could result in serious or even fatal injury or property damage from fire or explosion.

IF YOU SMELL GAS

• Shut off gas to the appliance.
• Extinguish any open flame.
• If the odor continues, keep away from theappliance and immediately call your fire department.

DANGER
! Never operate this appliance unattended.
! Never operate this appliance within 24 ” / 60 cm of any structure, combustible material, or gas cylinder.
! Never operate this appliance within 30 ” / 75 cm of any flammable liquid.
! Never allow oil or grease to get hotter than 400 °F / 200 °C. If the temperature exceeds 400 °F / 200 °C or if the oil begins to smoke, immediately turn the burner or gas supply OFF.
! Heated liquids remain at scalding temperatures long after the cooking process. Never touch the cooking appliance until liquids have cooled to 115 °F / 45 °C or less.
! If a fire should occur, keep away from the appliance and immediately call your fire department. Do not attempt to extinguish oil or grease fire with water.
Failure to follow these instructions could result in fire, explosion, or burn hazards which could cause property damage, personal injury or death.

GENERAL DANGERS

! Liquid gas is highly flammable and highly explosive.
! If the concentration of gas is too high, asphyxiation due to lack of oxygen can result.
! Liquid gas weighs more than air and can accumulate in depressions or if it escapes uncontrolled, can lead to gas concentrations that present a health risk in
small, poorly ventilated yards. This Otto Grill Lite is, therefore, intended exclusively for outdoor use and for use in areas with adequate ventilation.
! You should make sure that liquid gas does not escape uncontrolled.
! Instructions of the manufacturer or provider of the gas cylinder that is being used must be followed.
! Follow the instructions relating to the connection of the gas pressure regulator provided for the gas grill.
! Ensure that no ignition sources are located in the proximity of the grill when connecting the gas cylinder, especially open fires or lit cigarettes, candles,
lamps etc. Electronic devices can also pose a risk in the event that gas escapes during connection.
! If the gas hose is porous or defective, the grill must not be put into operation.
! If your gas hose has exceeded its expiration date, if required by national regulations and/or their applicability, or if porous or defective areas are present, it should be replaced.
! If you have not used your Otto Wilde Grillers gas grill for a long time, check for gas leaks prior to use.
! Never use an open flame to search for gas leaks.
! Do not use your Otto Grill Lite if there is a possibility of or in the event of a gas leak.
! Thoroughly clean your Otto Grill Lite at regular intervals in accordance with the ‘Cleaning’ instructions.
! Liquid propane gas is not natural gas. Modification of the grill to use natural gas and any attempts to use natural gas with this liquid propane gas grill are dangerous and prohibited. Any attempts to do so will immediately void the warranty.
! A dented or rusty gas cylinder can be dangerous and should be tested by your gas supplier.
! Do not use gas cylinders with damaged valves.
! Gas cylinders that appear to be empty may still contain gas. These gas cylinders should be transported and stored accordingly.
! After use, turn off the gas supply on the gas cylinder.
! Do not carry out any modifications or alterations to your Otto Grill Lite.
! The Otto Grill Lite is not intended to be installed in or on a boat or recreational vehicle.
! Do not install this model of the grill in an integrated or slide-in construction. Failure to do so may cause fire or explosion, resulting in serious injury, death, or property damage.

DURING OPERATION

! Take care when using your Otto Wilde Grillers gas grill. The grill gets hot when it is in use. Never leave the grill unattended, and do not move the grill when it is in use.
! In the event that uncontrolled flames shoot up, remove the food product from the flames until they die down.
! Whilst operating the grill, never touch the front, side or back of the grill chamber.
! Keep the gas supply hose away from any heated surfaces.
! This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from hot surfaces or splatter from cooking liquids.
! Keep the grilling area free of flammable gases and liquids, such as fuel, alcohol, and other combustible materials.
! In the event that the burner extinguishes whilst the grill is in operation, close the valve on the gas cylinder. Wait five minutes before attempting to re-ignite your grill in accordance with the ‘Ignition’ instructions.
! Do not store spare or unconnected gas cylinders in the proximity of the grill.
! Do not leave the appliance unattended. Keep children and pets away from the Otto Grill Lite at all times.
! Do not place the gas hose in walkway areas. Make sure the gas hose is not exposed where it can be accidentally tripped over, tipping the gas supply cylinder. ! Do not use your Otto Wilde gas grill in heavily frequented areas.
! Never, under any circumstance, attempt to disassemble the gas regulator or other assembly parts of the gas supply while the grill is in use.
! Do not cover the burners for extended periods of time (>5 minutes), e.g. by placing the drip tray or pizza stone directly underneath the burners. Blocking the burners may cause backlashing of the flames and can seriously damage the burners. In case that a blacklash occurs, turn off the burners and gas supply immediately and contact the Otto Wilde Grillers, service team.
! The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate this appliance.
! Avoid bumping of or impact with the appliance to prevent spillage or splashing of hot cooking liquid.
! Do not obstruct the flow of combustion or ventilation air.

RISK OF FIRE
! Flammable materials must not be present within an area of 24 “/ 60 cm behind or to the side of the grill.
! Do not use charcoal, briquettes, or other fuels in your Otto Grill Lite. Fire hazard!
! In the event that fats start to burn, turn off the gas supply on the gas cylinder and let the fats burn. Never attempt to extinguish burning fat with water, as this leads to explosions.
! Make sure that dry food, such as bread, does not start to burn.
! Do not put the grill cover or other flammable items on top of the grill. Fire hazard!
! Greater accumulations of fat should be avoided and optionally removed.
! When grilling meat with high fat put water into the drip tray and make sure to empty the drip tray frequently to prevent grease fires.
! In the event of an oil or grease fire do not attempt to extinguish with water. Immediately call the fire department. A Type BC or ABC fire extinguisher may, in some circumstances contain the fire.

STORAGE
! When the Otto Grill Lite is not in use, the tap on the liquid gas cylinder must be turned off.
! If the Otto Grill Lite is stored in your house, the liquid gas cylinder must be removed and stored in an adequately ventilated space outdoors.
! If the liquid gas cylinder is not removed from the Otto Grill Lite, the grill must be stored in an adequately ventilated space outdoors.
! Liquid gas cylinders must be stored in an adequately ventilated space outdoors that is not accessible to children. Liquid gas cylinders must not be stored in
a building, garage, or any enclosed area.
! This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.
! Read and follow all warnings and instructions before assembling and usin the appliance.
! Follow all warnings and instructions when using the appliance.
! Keep this manual for future reference.

WELL PREPARED
BEFORE YOU START

USAGE
Your Otto Grill Lite is designed exclusively for grilling food.
Your Otto Grill Lite is designed for use in private households and the quantities normally produced there.
! The Otto Grill Lite may only be used outdoors.
! The Otto Grill Lite must not be used as a built-in appliance.
! This device is not suitable for use in aviation, shipping, and passenger vehicles.
! The manufacturer accepts no liability for damage resulting from improper use.

WHAT YOU GET
SCOPE OF DELIVERY

Your Otto Grill Lite comes with multiple parts, which are listed individually below. Before using your Otto Grill Lite for the first time, make sure that you have received all these parts.

BEFORE FIRST USE
Clean all parts that come into contact with food, especially the cast iron grill and the grease trap.

PEOPLE WHO READ LIVE LONGER

GAS INSTRUCTIONS

WARNING
! We recommend that your LP cylinder be filled at an authorized LP gas dealer by a qualified attendant who fills the tank by weight. Improper filling is dangerous!
! Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only use the appropriate dust cap provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.
! Replacement LP tanks must match the regulator connection supplied with this Otto Wilde Grillers gas appliance.
! Never store a spare LP cylinder under or near Otto Wilde Grillers gas appliances.
! Never fill the tank beyond 80 % full. Failure to follow these statements exactly may result in a fire causing death or serious injury.
! Only use Otto Wilde Grillers gas appliances outdoors in a well ventilated area. Do not use in a garage, building, breezeway or any other enclosed area.

IMPORTANT CYLINDER INFORMATION
! Your Otto Wilde Grillers grill is equipped for a cylinder supply system designed for vapor withdrawal.
! The proper filling methods for the filling of your cylinder are by weight or volume, as described in NFPA 58. Please make sure your filling station fills your LP cylinder by weight or volume. Ask your filling station to read purging and filling instructions on the LP cylinder before attempting to fill.

SAFE HANDLING TIPS FOR LIQUID
PROPANE GAS CYLINDERS
! Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP gas is a gas at regular temperatures and pressures. Under moderate pressure, inside a cylinder, LP gas is a liquid.
! As the pressure is released, the liquid readily vaporizes and becomes gas.
! LP gas has an odor similar to natural gas. You should be aware of this odor.
! LP gas is heavier than air. Leaking LP gas may collect in low areas and prevent dispersion.
! To fill, take the LP cylinder to a propane gas dealer or look up “gas- propane” in the phone book for other sources of LP gas.
! Air must be removed from a new LP cylinder before the initial filling. Your LP dealer is equipped to do this.
! The LP cylinder must be installed, transported, and stored in an upright position.
! LP cylinders should not be dropped or handled roughly.
! Never store or transport the LP cylinder where temperatures can reach 125 °F/50 °C (too hot to hold by hand) For example: Do not leave the LP cylinder in a car on a hot day.

Note: A refill will last about 20 – 25 hours of cooking time at normal use. You do not have to run out before you refill.
! Treat “empty” LP cylinders with the same care as when full. Even when the LP tank is empty of liquid, there still may be gas pressure in the cylinder. Always close the cylinder valve before disconnecting.
! Do not use a damaged LP cylinder. A dented or rusty LP cylinder or an LP cylinder with a damaged valve may be hazardous and should be replaced with a new one immediately.
! The joint where the hose connects to the LP cylinder must be leak tested each time the LP cylinder is reconnected. For example, test each time the LP cylinder is refilled. ! Be sure the regulator is mounted with the small vent hole pointed downward so that it will not collect water. This vent should be free of dirt, grease, bugs, etc.

LIQUID PROPANE CYLINDER REQUIREMENTS

! Check to be sure that cylinders have a D.O.T. certification 1, and that they have been date tested 2 within five years of use. Your LP gas supplier can do this for you.
! All LP tank supply systems must include a collar to protect the cylinder valve.
! The LP cylinder must be a 20-lb./ 11 kg size approximately 18 “/ 59 cm high and 12 “/ 34 cm in diameter.
! The cylinder must be constructed and marked in accordance with the specifications for LP-gas cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN / CSA-B339, Cylinders, Spheres and Tubes or Transportation of Dangerous Goods; and Commission, as applicable.

LEAK CHECK PREPARATION
Check that all Burner Valves are Off Valves are shipped in the OFF position, but you should check to be sure that they are turned off. Check by pushing down and turning clockwise. If they do not turn, they are off. If they do turn, continue turning them clockwise until they stop, then they are off.

THE LIQUID PROPANE CYLINDER
All Otto Wilde Grillers LP gas grill regulators are equipped with a UL-listed tank connection as per the latest edition of ANSI Z21.58. This will require a liquid propane tank that is similarly equipped with a Type 1 connection in the tank valve.
This Type 1 coupling allows you to make a fast and totally safe hookup between your gas grill and your liquid propane tank. It eliminates the chance of leaks due to a POL fitting that is not properly tightened. Gas will not flow from the tank unless the Type 1 coupling.

WARNING
! Make sure that the LP cylinder valve is closed. Close by turning the valve clockwise.
DANGER
! Do not search for gas leaks using an open flame. Before checking for leaks, make sure that there are not any sparks or open flames in the vicinity. Sparks or
open flames can trigger an explosion, which could lead to serious or even fatal injuries or material damage.

TYPE 1 CONNECTIVE COUPLING
1| Type
2| Hand Wheel
3| External Thread
4| Thermally
5| Propane Regulator

HERE WE GO COMMISSIONING

CONNECTING THE PROPANE GAS CYLINDER

You require the following for a safe connection:

• Propane gas cylinder
• A foaming agent (e.g. leak detection spray, soap solution)

Place the propane gas cylinder in an upright, secure position
Position the gas cylinder in such a way that it is upright and secure and ensure that it does not come into contact with any part of the Otto Grill Lite. Position the gas cylinder at a distance of at least 24″/ 60 cm from the Otto Grill Lite so that the radiation heat does not reach the surface of the gas cylinder or that of the gas hose. Also, ensure that the gas hose is not under any tension. We recommend setting up the gas cylinder behind and slightly to the right of the Otto Grill Lite.

1. Make yourself aware of the quick-connect gas inlet Your Otto Grill Lite is fitted with a quick-connect gas inlet connection. The gas pressure regulator assembly is equipped with a matching female fitting.

2. Pull back the sleeve on the female fitting Pull back the sleeve on the female quick connect fitting and attached to the fitting on the grill.

3. Connect the hose to the device Continue to pull back the sleeve on the female quick connect fitting and push it all the way onto the device side male quick connects fitting.

4. Release the sleeve and ensure the connection is locked into place.

5. Connect the Otto Grill Lite to the cylinder The regulator on the other end of the hose (which is not yet connected to the grill) is fitted with a nut that
   matches the Type 1 connection on propane cylinders. Screw the regulator onto the cylinder outlet connection and ensure the connection is tight.

CHECK THE CONNECTION POINTS FOR LEAKS

Apply the foaming agent to both joints of the gas hose and the joint between the gas inlet and adapter fitting. Open the valve on the gas cylinder. Now check both joints and check whether bubbles appear. lf bubbles appear or if a bubble that was already present gets bigger, there is a leak. In the event of a leak, close the valve on the gas cylinder. Then check whether the gas hose is connected correctly and fastened tightly. lf the screw connection is loose on one of the connection points, tighten it.
After doing so, open the gas cylinder valve once more and use a soap solution to test whether the connection points are sealed. lf leaks are still present at one of the connection points, contact your retailer or our customer service team.
Visit our website for general contact information on: www.ottogrills.com
After completing the test for leaks, turn off the gas supply on the propane gas cylinder and clean the connections using water.

GENERAL

! Installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI 2223.1 / NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2 / NFPA 1192, and CSA 2240 RV Series, Recreational Vehicle Code, as applicable.
! The pressure regulator supplied with this appliance must be used. This regulator is set for 11 “/ 28 cm of water column (pressure / 2.8 kPa.)
! Your Otto Grill Lite is designed for use with liquid propane (LP) gas only. Do not use natural (piped-in-city) gas. The valves, orifices, hose, and regulator are for LP gas only. ! Do not use with charcoal fuel.
! The areas around the LP cylinder must be free and clear from debris.
! Replacement pressure regulators and hose assemblies must be those specified by Otto Wilde Grillers.

OPERATING

! Only use this appliance in a well-ventilated area. Do not use in a garage, building, breezeway, or any other enclosed area.
! Your Otto Grill Lite shall not be used under overhead combustible construction.
! Your Otto Grill Lite is not intended to be installed in or on recreational vehicles or boats.
! Do not use this appliance within 24 “/ 60 cm of combustible materials.
! The entire cook box gets hot when in use. Do not leave unattended and do not touch.
! Keep the fuel supply hose away from heated surfaces.
! Keep the cooking area clear of flammable vapors and liquids such as gasoline, alcohol, etc., and combustible materials.
! Never store an extra (spare) LP cylinder under or near your Otto Grill Lite.
! The LP cylinder used with your grill must be with a listed OPD (Overfilling Prevention Device) and a QCC1 or Type 1 (CGA810) cylinder connection. The cylinder connection must be compatible with the appliance connection.

WARNING
Every single time, before you use your Otto Grill Lite, check the gas hose for kinks, cracks, abrasion, wear or cuts. If you establish that the gas hose is damaged, do not use the grill until you have replaced it. The gas hose must be replaced with one that is approved by Otto Wilde Grillers. Contact your retailer or our customer services department for more information.

IGNITION BY PIEZOELECTRIC IGNITER

1. Take a position to the side of your Otto Grill Lite, as flames may escape from the front opening during the ignition process.
2. Make sure that the indicator of the control knob points to „0“.

! Before opening the valve on the propane gas cylinder, the control knob must be in the Off position.

3. Now push the control knob down and turn it in one continuous movement into the ignition position, so that the indicator points to the ignition symbol.  During the rotation, you should hear a clicking noise twice. Press and hold the control knob for another 3seconds before releasing it. The pilot burner, which is mounted under the two burner plates in the middle of the rear wall, should now burn.
   ! Never put your head in or directly in front of the grilling chamber of your Otto Grill Lite to test whether the burners are already ignited or ever while operating the appliance. During the entire ignition process, keep your face and body at least 15 “/ 38 cm away from the front opening as flames may escape from the grilling chamber while igniting the gas.

4. Make sure the pilot burner is burning.

5. To ignite the burners, press down the control kno b again and turn it until the indicator points to the large flame symbol. This should cause the two burners to ignite

6. Check to see if the burners are lit. Look into the front opening of your Otto Grill Lite, observing the minimum distance of 12 “/ 30 cm. There must be a flame under the burners.

DANGER
! Should the flame get extinguished by accident, turn the control knob for the burner to the starting position and close the valve on the propane gas cylinder.
! Wait at least 5 minutes before reattempting to ignite the burner using the piezo igniter or a match, to allow unburnt gas to escape from the inner area of your Otto Grill Lite.

MANUAL IGNITION

If the pilot flame was not ignited by the piezo igniter:

1. Take a position to the side of the Otto Grill Lite due to possible flame leakage during ignition.

2.  Now ignite firewood with a length of at least 8 “/20 cm and insert it into the grill chamber of your Otto Grill Lite so that the flame is positioned slightly below the pilot burner. You can also use a stick lighter.
   ! Before opening the valve on the propane gas cylinder, the control knob must be in the Off position and must not already be pushed down.

3. Now press and hold the control knob down and turn until you hear 2 clicks and the knob is in the ignite position. After you hear the ignition noise of the pilot, press and hold the control knob for another 5 seconds.

4. Make sure the pilot burner is burning.
   ! Never put your head in or directly in front of the grilling chamber of your Otto Grill Lite to test whether the burners are already ignited or ever while operating the appliance. During the entire ignition process, keep your face and body at least 15 “/ 38 cm away from the front opening as flames may escape from the grilling area while igniting the gas.

5. To ignite the burners, press down the control knob again and turn it until the indicator points to the large flame symbol. This should cause the two burners to ignite.

6. Check to see if the burners are lit. Look into the front opening of your Otto Grill Lite, observing the minimum distance of 12 “/ 30 cm. There must be a flame under each burner.

DANGER
! In the event that the burner has failed to ignite, turn the control knob for the burner to the Off position and close the valve on the propane gas cylinder. Wait at least 5 minutes before making another ignition attempt using the piezo igniter or a match, to allow unburnt gas to escape from the inner area of your Otto Grill Lite.
! If you do not allow 5 minutes for the gas to escape in the event that the Otto Grill Lite fails to ignite, an explosive flame can be produced, which could lead to serious or even fatal injuries.

COMMISSIONING

GRILLING PROCEDURE

1. Use the lever to remove the grill grate from slide-in slots 1 and place it next to the Otto Grill Lite on a heat-resistant surface with sufficient space.
2. Light your Otto Grill Lite as described in the sections “Ignition by piezoelectric ignitor” or “Manual ignition”.
3. Fill the drip tray halfway with water and place it in a slot below the desired grill height. 2
4. Wait 2-3 minutes for the burners to reach operating temperature.
5. Place your food on the grill grate.
6. Use the control knob to adjust the required grill intensity of the burners.
7. Use the lever to put the grill grate back on the sliding slot, leave in the desired slide-in slot until your food has reached the desired temperature.
8. Remove the grill grate to turn your food and repeat step 7 to grill your food on the other side.

Use the heat protection plate
Pull out the heat shield inserted at the bottom of the Otto Grill Lite either completely or at least to the front edge of the installation surface. The heat protection plate prevents inadmissible heating of the installation surface by heat radiation escaping from the grill.

WARNING
! The whole appliance becomes very hot. Take special care if children or elderly people are nearby.
! Always wear protective gloves when using your Otto Grill Lite.
! Before you remove the drip tray once the grilling process is complete, wait until this and the interior of the Otto Grill Lite has cooled down sufficiently.
! When cooking, the Otto Grill Lite must be on a level, stable, non- combustible surface in an area clear of combustible material. An asphalt surface (blacktop) may not be acceptable for this purpose.
! Never move your head or limbs in or directly in front of the opening of your Otto Grill Lite to test how well-cooked your food is. During the entire grilling process, keep your face and head at least 15 ” / 38 cm away from the grill chamber.

GOOD TO KNOW

CLEANING

Switch off your Otto Grill Lite, and wait until the grill including all removable parts is completely cooled down. Close the valve of the gas cylinder and unscrew the gas line before you start cleaning.

OUTSIDE SURFACE
You can clean them with a cloth and warm soapy water. When you have finished cleaning, rinse thoroughly with water to remove any soap residue.

INSIDE SURFACES
Loosen the two grate inserts in the cooking chamber of your Otto Grill Lite by unscrewing the two knurled nuts counterclockwise. Remove the grate drawer and put it aside. The spacer bolts do not necessarily have to be loosened every time the unit is cleaned. If necessary, loosen the two spacer bolts by unscrewing them counterclockwise from the thread in the side wall of your Otto Grill Lite. Put them aside as well and repeat the steps for the opposite grating. Now you can clean the inner surfaces of your Otto Grill Lite with a cloth and warm soapy water. The ceramic plates of the burners do not need to be cleaned. When you have finished cleaning, rinse thoroughly with water to remove any soap residue. When cleaning the burner unit, make sure that no water runs into the burners. Clean the stainless steel surfaces of your Otto Grill Lite only with a soft cloth and soapy water. Fasten the 4 spacer bolts again in the provided threads on the inside of your Otto Grill Lite. Now insert the grate inserts and fix them with the 2 knurled nuts. Note: You can also use steel wool to remove stubborn dirt. However, you should make sure that you always rub in the direction of the brush over the dirty surface to avoid scratches.

CAST IRON GRILL GRATE
Use a dishwashing brush to brush your cast iron grill under warm running water. When you have removed all the barbecue residues from your grate, dry it thoroughly with a dish towel. Then smash your grill into a cloth and stow it until the next use. Note: To dry your cast iron grill, use an older tea towel so that no Fat leftovers will ruin your favorite towel.
REMOVABLE GREASE DRIP TRAY
Remove the grease residues extensively with paper towels before washing out the grease trap with warm soapy water. Rinse the grease trap thoroughly again with clear water.

IMPORTANT
Do not use cleaners containing acid, benzine or xylene. Rinse thoroughly with water after each cleaning operation. Never clean the stainless steel surfaces of your Otto Grill Lite with a wire brush. Such a brush causes scratches. When drying and wiping surfaces, make sure that you wipe in the brushing direction of the metal. This way you avoid visible scratches on the surfaces.
STORAGE
When the Otto Grill Lite is not in use, the tap on the LPG bottle must be turned off. If the Otto Grill Lite is to be stored indoors, the LPG bottle should be removed and stored in a well-ventilated place. If the LPG bottle is not removed from the Otto Grill Lite, the grill and LPG bottle must be stored outdoors in a well-ventilated place. Liquid gas cylinders must be stored in a well-ventilated place out of reach of children. Removed LPG cylinders must not be stored in a building, garage or another closed area.

IT’S GETTING HOT
BAPTISM OF FIRE

At some point, you just have to start. And nothing is better than a juicy ribeye steak. The Otto Grill Lite has a reputation for covering this classic premium cut with a crunchy crust in just a few seconds while the meat remains soft, pink, and juicy on the inside. At this point, you know: Steakhouse quality is now available in your home. Many more recipe ideas (not only for meat), tutorials, and information can be found at: www.ottogrills.com

INGREDIENTS
FOR 4 PEOPLE
4 Ribeye steaks
approx. 0.6 lb. / 300 g each
2.2 lbs. / 1 kg Sweet potatoes
1-2 Red bell peppers
3 sprigs of thyme
Rosemary
Coarse salt
Colored pepper

1. PREPARATION
   Take the ribeyes out of the fridge one hour before you plan on grilling them. Let them reach room temperature for an even cooking process. In the meantime, cook the unpeeled sweet potatoes in salt water for 10 to 15 minutes. The potatoes shouldn’t get too soft, because otherwise, they will fall apart on the grill grate. Cool down and cut into slices. Chop thyme and fresh rosemary. Remove the core of the bell pepper and cut into slices.

2. PREHEATING
   For the perfect ribeye the Otto Grill Lite should be preheated to maximum temperature. That takes about three minutes. Keep the grill grate out off the grill, so the ribeye doesn’t get precooked on the hot grill grate.

   ---

3. GRILL THE PERFECT RIBEYE
   Crucial when grilling meat: the right temperature. Only when the grill is really hot you will trigger the so-called “Maillard reaction”. Amino acids react with sugar and gives your steak a nice crust. Read more about the Maillard reaction on our Blog. Set the grate on the lowest slide-in slot and grill the ribeye at 1500 °F / 815 °C for 1 minute on each side. This applies if your steak is about 1 ” / 2.5 cm thick. If it’s bigger, use a meat thermometer for the best outcome. Your desired core temperature would be between 125 – 131 °F / 50 – 55°C. Afterward, remove the ribeye from the grill grate and let it rest. This gives the meat juices the chance to redistribute themselves within the meat again. Read the article “Grilling the perfect steak” on our website for more steak know-how.

4. GRILL THE SIDES AND SERVE
   Sear the sweet potato slices at the moderate temperature on one of the lower slide-in slots on both sides until they’ve turned golden-brown in color. Coat with olive oil and season with fresh herbs, coarse sea salt, and pepper.
   Then, carve the dry-aged ribeye across the grain and also season with coarse sea salt. Serve with the grilled sweet potato slices on a country-style wooden board for the right looks. And now: enjoy!

NOTE
It may be the case that the temperature of your new Otto Grill Lite turns out a little bit higher than indicated in our recipes the first few times you use it on specific burner settings.
This is simply because the surfaces are still especially shiny and highly reflective. The conditions that exist when grilling, such as wind or weather may make it necessary to adjust the control knob or grilling position in order to achieve the desired cooking temperature.
In order to always be on the safe side and to ensure that your product is cooked as desired, We recommend the use of a meat thermometer.

YOUR GRILL DOESN’T WORK PROPERLY ANYMORE
WHAT WOULD OTTO DO?

Pillot burners do not Ignite, despite adjustment knob pressed down to the Ignition position.| No ignition spark.| Move the control knob to the zero position. look into the cooking chamber and observe whether ignition sparks are generated when pressing down and turning the control knob to the ignition position.
The valve on the gas cylinder is not open.| Open the valve by turning it counterclockwise.
I. Pressure regulating valve defective. 2. Connections are not tight.| 1. Replace the pressure regulating valve.
2. Check connections for leaks.
Tube squeezed in or kinked off.| Check hose installation for proper installation.
No gas for burners.| First check whether gas flows through the burners. Press down the control knob in the large position without actuating the piezo igniters. You must hear gas flowing. if this is not the case, disconnect the hose from the unit and check whether the connection is blocked. Webb dues the case is clean.
Burner goes off during operation.| Grill food has come into contact with the flame monitor (temperature sensor).| Place the food in such a way that it cannot come into contact with the temperature sensor. Re-ignite the affected burner.
Burner, however, operates with clearly reduced performance.| 1. Dirty gas duct or nozzles. 2. Broken ceramic plates.| Have the device repaired at OWG.
One or both burners do not ignite, despite burning pilot flame.| Gas flow or nozzles blocked.| Notify Otto Wilde Customer Service.

LAST BUT NOT LEAST

WARRANTY

WARRANTY AND
DISCLAIMER OF LIABILITY
The Otto Grill Lite is suitable exclusively for outdoor use and only for its intended private use.

! This product has been subjected to a safety test and is intended for use in a specific country only.
Information with the country identification can be found on the type plate on the back of the device and on the outside carton.
! Any modifications or alterations to this grilling appliance will invalidate the warranty. For this reason, do not carry out any modifications to the appliance.
Despite the favorable cleaning characteristics of the Otto Grill Lite, the accumulation of fatty residues on the grill and inside the burning chamber are unavoidable in the long-term. These do not constitute cause for complaint. As the front panel is subject to combustion smoke and high temperatures, discoloration in this area is unavoidable and does not constitute cause for complaint. These parts are components that transfer or burn gas. For information regarding the original spare parts of Otto Wilde Grillers, contact the Otto Wilde customer service team.
! Never attempt to repair components that transport or burn gas yourself. If this product warning is not observed, actions may lead to a fire or explosion. This can cause serious personal injury, fatal accidents, and material damage. For any questions relating to repairs, contact the Otto Wilde customer service team.

CONTACT US
Otto Wilde Grillers Inc.
80 Pine Street
New York, NY 10005
Service Hotline
+1 855-505-5646
E-Mail
service@ottogrills.com
Recipes, tips, and much more
www.ottogrills.com

Scan the QR-Code with the camera of your smartphone or your tablet to open the website to get further video instructions and video tutorials.

http://tiny.cc/aqpwtz
Share your grill experience with us!

Otto Wilde Grillers Inc.
12600 Hill Country Blvd
Suite R-130 #293
Austin, TX 78738
+1 855-505-5646
service@ottogrills.com
www.ottogrills.com

References

• Infrared Grills by Otto Wilde - Top Steakhouse Quality Portable Grill

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>