OTTO WILDE G32 MCU Gas Grill Instruction Manual

TTO WILDE G32 MCU Gas Grill

G32 MCU Function description

1. Wi-Fi Touch Button / LED Indicator
2. Bluetooth (BLE) Touch Button / LED Indicator
3. Gas Stock Indicator
4. Photodiode
5. Antenna Window
6. Meat Probe Sockets 3#,4#
7. Meat Probe Sockets 1#,2#
8. Main Power Switch

Standby Mode

Press

Power On

| Standby wait for further

operation

| Wi-Fi Off

BLE Off

Gas Stock

| No

Condition
Power on and self-check passed.

Wi-Fi Function

Wi-Fi Configuration

Condition: in Standby mode

Gas Stock

| 2 beeps 2s/5s

Device (MCU) switch to AP mode, the grill will be a Hot Spot and can be found in the Wi-Fi list of Mobile devices Follow the Instruction in APP to finish the Wi-Fi Configuration (provide SSID and Password)

Quit Mechanism / Output

• Time out (150s) or Configuration not succeed: quit to A. Standby Mode.
• Success Configurated: go to B3. Wi-Fi Data Transfer.
• Press Wi-Fi1 5-10s, quit to A. Standby Mode.

WIFI Connection

Condition: in Standby mode, Wi-Fi Configuration has been done before (SSID and Password are stored in the memory.

BLE 2 Off

Gas Stock

| 1 beep 2s

System will try to connect the server

Quit Mechanism/Output

• Time out/connection not succeed WIFI Flash 2 times beep 1 once. go to A. Standby
• Success connected: go to B3 WIFI Data Transfer.

Wi-Fi Data Transfer

BLE 2 OFF

| No

Quit Mechanism/Output

• Connection lost/Time out: quit to A. Standby
• Press Wi-Fi 1 5-10s, quit to A. Standby Mode.

Wi-Fi Clear

BLE 2 OFF

| 3 beeps

2s/5s/10s

All stored WiFi Configuration Information will be deleted.

Bluetooth BLE Function

BLE Configuration

Condition: in Standby mode

BLE  flash in 2Hz

Gas Stock

| 2 beeps 2s/5s

Device (MCU) switch to BLE Paring mode, the grill can be found in the BLE list of Mobile devices Follow the Instruction in APP to finish the BLE Configuration

Quit Mechanism / Output

• Time out 150s or Configuration not succeed go to A. Standby.
• Success Configurated: go to C2. BLE Data Transfer.
• Press BLE 5-10s, quit to A. Standby Mode.

BLE Data Transfer

Condition in Standby mode, BLE Configuration has been done.

BLE 2 flash in 2Hz

Gas Stock 3

| No

Device (MCU) switch to AP mode, the grill will be a Hot Spot. Follow the Instruction in APP to finish the Wi-Fi Configuration (provide SSID and Password

Quit Mechanism / Output

• Connection lost/Time out quit to A. Standby.
• Press BLE 5-10s, quit to A Standby Mode.

Halogen Light Control

In any STATE
If the illuminance near the Photo Diode is smaller than 75 Lux AND the Hood is open (magnet on the hood away from reed in operation panel) The System will turn on the Halogen Light.  When the Halogen Light is ON.  If the illuminance near the Photo Diode is rises more than 125 Lux OR the user closes the Hood The System will turn off the Halogen Light.

Gas Buddy Gas Stock Indicator

• Gas N.W. < 1 kg → red LED on.
• Gas N.W. > 1 kg → white LED on.
• Cable Gas buddy Module not connect → LED OFF

OTA Mode

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>