OTTO WILDE Pro Infrared Steak Grill Drawer Instruction Manual
- June 12, 2024
- OTTO WILDE
Table of Contents
OTTO WILDE Pro Infrared Steak Grill Drawer
PRODUCT INFORMATION
The Grill Drawer is a convenient grate and drip tray drawer made out of stainless steel. It is designed to fit the Otto Wilde Grill or Electric Otto Wilde Grill* (only available in countries with a voltage supply of 220-250 V and a frequency of 50 Hz). The Grill Drawer comes with a multitool that allows you to easily pull out the drawer, flip your food and push the drawer back in. The drip tray moves with the drawer, minimizing the risk of hot grease falling onto surfaces where it is not wanted.
SCOPE OF DELIVERY
The Grill Drawer comes with the following accessories:
- 1x Grill Drawer Rostauszug
- 2x Roller block Rollenbock
- 4x Shoulder screws Sonderschrauben
- 2x Rounded head screws Halbrundkopfschrauben
PREPARATION
- Place your Otto Wilde Grill on a suitable table or workbench.
- Remove the top from the base and remove the grill grate and grease tray.
ASSEMBLY
- Remove the front cover from the drawer by unscrewing the two knurled screws.
- Remove the roller blocks and the rounded head screws from the rails.
- Place the left guide rail on the side wall of the base, so that the lower hole of the rail is centered over the threaded hole of the lower lever arm.
- Guide the threaded end of the shoulder screw through the opening of the retaining plate and fasten it to the lower lever arm.
- Position the protective cover in front of the frame and guide it downwards until the lateral slots of the cover slide over the pins of the frame.
USAGE
To use the Grill Drawer, insert the lever at a slight angle into the slot in
the front cover and pull the Grill Drawer out by applying slight downward
pressure. Avoid jerky movements when moving in or out to prevent splashing of
hot grease. Make sure to check that the Grill Drawer sits properly in the
rails, can be moved easily, and that the outward travel is limited by the
roller blocks after each installation/removal of the Grill Drawer for cleaning
purposes.
Note: The Grill Drawer does not fit the Otto Wilde Grill Lite!
GREAT SLIDER
- Otto Wilde congratulates you on the purchase of our Grill Drawer. With the Grill Drawer you’ll no longer need to lift the grate out of the grill. Using the handy multi- tool, you can easily pull out the drawer, flip your food and push the drawer back in. Don’t worry, the drip tray moves with the drawer, minimizing the risk of hot grease falling onto surfaces where it is not wanted.
- We have developed our Grill Drawer completely according to the wishes of the Otto Wilde barbecue community. In our instructions we show you how to install your Grill Drawer safely and correctly in your Otto Wilde Grill or Electric Otto Wilde Grill*. We congratulate you on the expansion of your Otto Wilde Grill family and wish you lots of fun with your new Grill Drawer!
- Your Otto, Alex, Julia and Nils
SCOPE OF DELIVERY
Here is a list of accessories that belong to the Grill Drawer. Quickly check that all the parts are there and use the screws supplied.
PREPARATION
- Place your Otto Wilde Grill on a suitable table or workbench.
- Open the buckles on the back of the unit.
- Remove the top from the base and remove the grill grate and grease tray.
DISASSEMBLY
-
Before starting the assembly, remove the front cover from the drawer by unscrewing the two knurled screws.
-
Also remove the roller blocks and the rounded head screws from the rails.
KEEP THE SCREWS IN A SAFE PLACE! -
Loosen the currently installed screws of the grate supports on the right and left side with the torx key.
ASSEMBLY
-
Turn the base onto its left side.
-
Release the brake, on the back of the base, by turn- ing it CCW. Slide the lower lever arm to a position as shown in the diagram and close the brake by turning it CW.
-
Place the left guide rail on the side wall of the base, so that the lower hole of the rail is centered over the threaded hole of the lower lever arm.
-
Guide the threaded end of the shoulder screw through the opening of the retaining plate and fasten it to the lower lever arm.
PERFORM THE SAME STEPS FOR THE RIGHT SIDE. -
To fasten the upper lever arm, slide it into the position where the threaded hole is centered under the hole of the retaining plate and push the upper lever arm upwards with your index finger so that the lever arms do not move.
-
Turn the base back to the horizontal position.
-
To assemble the frame of the drawer, position the rollers attached to the ends over the openings of the guide rails. Lift the frame at the front.
-
Insert the rollers into the openings, lower the frame at the front and slide it to the back stop.
-
Place a roller block on both sides in the openings of the guide rails and fas-ten the roller blocks to the guide rails with the roun-ded head screws using the holes provided.
-
Position the protective cover in front of the frame and guide it downwards until the lateral slots of the cover slide over the pins of the frame.
-
Now the front cover can be fixed from the inside of the frame with the two knurled screws.
USAGE
Insert the lever at a slight angle into the slot in the front cover and pull the Grill Drawer out by ap- plying slight downward pressure. Avoid jerky movements when moving in or out.
ATTENTION
-
Make sure that you have carried out all assembly steps described in this manual correctly, that the Grill Drawer sits properly in the rails, can be moved easily and the outward travel is limited by the roller blocks. Make sure to check these points after each installation/removal of the Grill Drawer for cleaning purposes.
NOTE: Due to the high temperatures the rails need sufficient play. This can, occasionally, cause slight jamming, which can be remedied by moving the Grill Drawer in and out again at a slightly adjusted angle.
NOTE: Due to the high temperatures we cannot use grease/oils for the moving parts. This can lead to friction noise when moving the Grill Drawer in and out. -
Avoid jerky movements when moving the Grill Drawer in and out, so that the grease tray does not spill over. Burning hazard!!!
-
To preheat the grill, remove grill grate and drip tray and move the Grill Drawer to the lowest position of the height adjustment, to avoid heat accumulating in the grill, which may cause flame flashbacks or temporary deformations of inner walls, inhibiting the movement of the Grill Drawer.
-
Always use the Lever, which you received with your Otto Wilde Grill, to operate the Grill Drawer, as well as, to insert and remove the grill grate. Never touch the drawer with your hand while the grill is in operation.
-
Avoid larger fat accumulations by emptying the drip tray regularly.
-
If greases catch fire, without moving the Grill Drawer, turn the control knobs to the zero position. Do not attempt to extinguish the flame with water. Explosion risk!!!
-
Wait to clean the grill until you have completed the grilling process and the Grill Drawer and the Otto Wilde Grill have cooled down sufficiently.
ABOUT COMPANY
- Otto Wilde Grillers Inc. 12600 Hill Country Blvd Suite R-130 #293 Austin, TX 78738
- +1 855-505-5646
- service@ottogrills.com
- www.ottogrills.com