VISUAL COMFORT RL 5673 Paxton 48 Inch Ring Chandelier Instruction Manual

VISUAL COMFORT RL 5673 Paxton 48 Inch Ring Chandelier

Specifications

• Product Name : Paxton 48 Ring Chandelier
• Item Number : RL 5673

Product Usage Instructions

Assembly Instructions

1. Remove all parts from the box and place them on a clean, soft surface.
2. Remove mounting plate (B) from canopy (J) by unscrewing screws (I).
3. Install mounting plate (B) to the junction box and secure it with mounting screws (E).
4. Connect the supply ground wire (usually green or bare copper) around the junction box ground screw.
5. Connect the fixture wires to the corresponding wires in the junction box, following the wiring diagram.
6. Secure all connections with wire nuts and electrical tape.
7. Attach the canopy (J) to the mounting plate (B) and secure with screws (I).
8. To level the fixture, adjust the cap nut (O) and feed the wires through the stopper (N) as needed.

Care Instructions

Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

FAQ

• Q: What tools are required for installation?
  • A : Phillips Screwdriver, Slotted Screwdriver, Wire Strippers, Measuring Tape, Wire Cutters.
• Q: How should I handle damaged parts?
  • A : If any damage or defect is found, do not install the fixture. Retain all packaging material until installation is complete and approved.

ASSEMBLY INSTRUCTIONS

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and  contents carefully. If any damage or defect is found, do not install.Retain all packaging material until installation is complete and approved

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Wire Cutters

INSTALLATION

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from canopy (J) by removing screws (I).

3. Install mounting plate (B) to the junction box and secure it with mounting screws (E).

4. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten.

   • NOTE : The fixture must be grounded.

5. Gently set the fixture on a flat, non-abrasive surface to adjust fixture hanging wires.

6. To adjust each hanging wire loosen screws (H) on either side of the cable lock nut (G) and adjust to the desired length. Once complete re-secure screws (H) and repeat steps with the remaining wires. (See diagram 2)

7. After fixture height is achieved shorten the wires by using a pair of cutters (not included), leaving 8” of wire length to connect to the driver (D).
   NOTE : Final leveling in later step will only allow for small adjustments. Make sure fixture height and fixture level are accurate before cutting wires.

8. Remove outer housing of wire by making a neat cut all the way around, about 1” from the end. Once cut is made, remove and discard the 1” piece of housing, exposing the electrical wires.

   • NOTE : Make sure not to cut too deep into the housing or electrical wires could become damaged.

9. Separate wires and strip insulation on each 5/8″.

10. Install heat sink plate (M) to canopy (J) and secure with screws (L), then install driver (D) to heat sink plate (M) and secure with other heat sink plate (K) using screws (E).

11. Connect fixture neutral wire (black) to driver (D) output wire (black) using wire nut (A).

12. Connect fixture hot wire (red) to driver (D) output wire (red) using wire nut (A).

    • CAUTION : Do not reverse the hot and neutral connections.

13. Run safety cable through hole on back of the mounting plate (B). Loosen cable lock and install to end of safety cable. Insert other end of cable through the cable lock and tighten ends with a screwdriver to secure.(see diagram 3)

14. Connect driver (D) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).

15. Connect driver (D) input hot wire (black) to the supply hot wire (usually black) using wire nut (A).

    • CAUTION : Do not reverse the hot and neutral connections.

16. Make sure all wire connections are tight, then carefully tuck into the junction box.

17. Install canopy (J) to mounting plate (B) and secure with screws (I).

18. To level fixture, unscrew cap nut (O), feed fixture wire through stopper (N) and then re-secure cap nut (O). Repeat as needed with other wires. (See diagram 2)

    • Care Instructions : Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>