GEPRC RAD VTX 5.8G 2.5W High Power VTX User Manual

RAD VTX 5.8G 2.5W User Manual

Specification:

Model: GEPRC RAD VTX 5.8G 2.5W
Input voltage: DC 7-36V(2-8S Battery)
Output: 5V@600mA(Power 5V to camera)
Input impedance: 75Ω
Protocol: IRC Tramp
Antenna connector: MMCX connector
Cable connector: GH1.25-6P connector
Output power: 25mW/200mW/600mW/1600mW/2500mW/Pit mode
Frequency tables: 40 CH/37 CH(FCC)/26CH(EU)
Video format: PAL / NTSC
Microphone: Built in microphone
Size: 36.5mmx36.5mmx12mm
Weight: 15g(without cable)
Mounting holes: 30.5mmX30.5mm(M3)

Features:

1. 2.5W super-power ,suitable for Long Range flight with good stability.
2. Six power levels: 25mW/200mW/600mW/1600mW/2500mW/Pit mode .
3. Two-layer board cooling structure,separate power BEC and main-board,reduc-ing and shielding from the insinal interference.
4. Temperature control protection function that can prevent high temperature burning.
5. Wide voltage input, supports 7V-36V voltage input.
6. VTX control protocol is IRC Tramp,supports OSD parameter adjustment.
7. VTX built in microphone,real-time return of Drone’s sounds.
8. Has 3 regional frequency tables to meet the needs of various regions.
9. Two function buttons, three indicator lights, easy to operate.
10. Mounting holes is 30.5mmx30.5mm.

Introduction:

1. How to set Channel:
   Press and hold for 3 seconds to enter the Channel Selection:LED Color| CH1| CH2| CH3| CH4| CH5| CH6| CH7| CH8
   ---|---|---|---|---|---|---|---|---
   Blue| Flash 1X| Flash 2X| Flash 3X| Flash 4X| Flash 5X| Flash 6X| Flash 7X| Flash 8X
2. How to set Band:
   Press and hold for 3 seconds to enter the Band Selection:

3. How to set Power:
   Press and hold for 3 seconds to enter the Power Selection :

WARNING:

1. Install antenna before use.
2. To prevent overheating, provide constant airfiow and a well ventilated environment.Install a cooling fan if operating in confined conditions.
3. The 5V Output is just used for a Camera/Cooling Fan! Don’t connect Power Input / Battery to 5V Output port. Otherwise the VTX will be damaged.

How to use IRC Tramp:

1. Connect the IRC Tramp port to the FC’s f ree UART-TX .
2. Open BetaFlight ,enter Ports tab,under perlpherals next to the UART-TX which is connected to the IRC port of the VTX select IRC Tramp,save the settings.
3. Enter configuraton tab,turn the OSD on under Other Features,save the settings.
4. Enter Video Transmitter tab ,Load from file ,save the settings.(The file can be downloaded from the GEPRC website.)
5. Turn on the remote control,THR middle,YAW left,PITCH up,enter the OSD menu.
   The PITCH moves the cursor up and down, and the ELE right to enter the next item. Finally,save and exit.

Frequency table:

Warranty Policy:

1. If VTX is damaged or unknow issue,please contact GEPRC. We’ll do our best to get this taken care of quickly for you.
2. Any impact damage, product liquid damage, high temperature burn or other artificial damage is not covered by warranty.

PS:

1. All components has been strictly inspected and tested before shipping.
2. If you have any problems, please cooperate with our engineers to figure out solutions. (E-mail: support@geprc.com.)

Include:

1 x GEPRC ROS VTX 2.5W
1 x 5.8G Antenna MMCX 72mm
1 x MMCX connector to SMA connector 82cm
1 x GH 1.25-6P connector cables 150mm
1 x Matching screw package

Contact:

Website: http://geprc.com

https://www.youtube.com/channel/UCiO4BcKHJfh3UfcM9Zy4D7Q

   https://geprc.com/support

References

• Professional FPV Product Provider - GEPRC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>