TAGU POWERFLAME 23PF1A Magna Electric Fireplace with Heating User Manual

TAGU POWERFLAME 23PF1A Magna Electric Fireplace with Heating

Specifications

• Model(s): 23PF1A, 23PF1B, 23PF1C, 23PF1C, 23PF1D
• Heating Power:
  • Nominal Power: 1.49 kW
  • Minimum Heating Power: 6.042 x 10-3 kW
  • Maximum Continuous Heating Power : 1.49 kW
  • Auxiliary Consumption at Maximum Power: 10.245 x 10-3 kW Electronic Room Temperature Control with Weekly TimerOpen Window Detection
• Voltage: 220-240V
• Frequency : 50 Hz
• Power Rating: 1260-1500 W
• Moisture Protection: IP X0
• Protection Class: Class I
• Power Cable : 1.8 meters, non-removable plug

Product Usage Instructions

Connection to Power Supply

Ensure the product is connected to a suitable power supply following the provided guidelines.

Battery Replacement

The remote control operates with 2 x AAA 1.5V standard batteries. Please dispose of used batteries at an appropriate collection point.

Assembly of Firebox

1. Insert the firebox from the rear.
2. Mount the fixing plates on both sides of the combustion chamber.
3. Secure the plates using the supplied screws.

Mounting in Wall or Brick Fireplaces

Refer to the TAGU 23RK1 Installation Kit user manual for detailed instructions on wall mounting the firebox.

FAQ

• Q: Is this product suitable for continuous use in all types of spaces?
• A: This product is only suitable for well-insulated spaces or occasional use.

INTRODUCTION

Congratulations on purchasing this electric fireplace. Please read the following instructions carefully and follow them to prevent possible damage. We assume no liability for damage caused by disregard of the instructions and improper use.
ONLINE USER MANUAL
To get online access to the latest user manual, scan the QR code or navigate to www.tagu.eu/manuals

www.tagu.eu/manuals

IMPORTANT SAFETY INFORMATION

IMPORTANT: These instructions should be read carefully and retained for future use.

1. Connect to properly grounded outlets only. This heater is for use on 220-240 volts. Never use with a regular extension cord or relocatable power tap (outlet/power strip).
2. If the appliance is damaged, check with the supplier before installation and operation.
3. Do not use outdoors.
4. Do not use it in the immediate surroundings of a bath, shower or swimming pool.
5. Do not locate the appliance immediately below a fixed socket outlet or connection box.
6. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
7. Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understanding the hazards involved.
8. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
9. Do not use this appliance in series with an external thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the appliance is accidentally covered or displaced.
10. Ensure that furniture, curtains or other combustible materials are positioned no closer than 1 metre from the appliance.
11. In the event of a fault unplug the appliance.
12. Unplug the appliance when not required for long periods.
13. Although this appliance complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.
14. The appliance must be positioned so that the plug is accessible.
15. If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard.
16. Keep the supply cord away from the front of the appliance.
17. Make sure the distance between the back of the heater and the wall is a minimum of 30mm.

WARNING : In order to avoid overheating, do not cover the heater. Do not place material or garments on the heater, or obstruct the air circulation around the heater, for instance by
curtains or furniture, as this could cause overheating and a fire risk.
WARNING : Servicing and product repairs should only be undertaken by the manufacturer’s approved service agent or a similarly qualified person, using only exact manufacturer-approved spare parts. CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

DIGITAL DISPLAY

The LED display allows you to view heat settings and functions easily. When a function is changed from the control panel or remote there will be a corresponding indicator displayed. NOTE: The display will automatically turn off after 60 seconds of idle.

CONTROL PANEL

REMOTE CONTROL

OPERATION AND FEATURES

TIME AND DAY
After plugging in the unit for the first time, you need to set the current time and day. Using the remote control, press and hold the SETTING BUTTON for 3 seconds. Use the PLUS BUTTON to set the hour, the MINUS BUTTON to set the minutes and the DAY BUTTON to set the day of the week. When finished, wait for the display to stop flashing and the time and day will be set.

ON/OFF
Press the POWER BUTTON on the control panel or the remote control to turn the unit ON or OFF. When turned OFF the embers of the log set will not immediately go out. This is a designed feature to represent the embers of the fire slowly fading out.

FLAME BRIGHTNESS

Press the FLAME BUTTON on the control panel or the remote control to raise or lower the level of flame brightness from 1 to 4. Level 5 will make the flame automatically glow dimmer and brighter creating a realistic fire effect.
HEATING
Press the HEATER BUTTON on the control panel or the remote control to turn the heating ON/OFF. After the heater has been turned off the fan may still run to prevent overheating.

TEMPERATURE AND THERMOSTAT

The thermostat setting range is 17°C – 27°C or 62°F – 82°F or constantly ON. If the room has reached the selected temperature the heater will automatically shut down and turn back on if needed. While the heating is on you can adjust the temperature of the thermostat:
USING THE CONTROL PANEL : press and hold the HEATER BUTTON for 3 seconds and after that press the button again to change the temperature. After selecting the desired value, press the FLAME BUTTON to save the setting and return to normal operation.

USING THE REMOTE CONTROL : press the PLUS BUTTON to raise the temperature and the MINUS BUTTON to lower the temperature.

SLEEP TIMER

This allows you to set the fireplace to automatically shut OFF after the amount of time displayed on the screen. Press the TIMER BUTTON on the remote control to set and cycle through the timer setting from 1-9 hours and off. Select the desired amount of hours and the firebox will automatically shut OFF after that selected amount of time.

RELAX
Not everything in life has a clear purpose. Press the RELAX BUTTON on the remote control to… sit back and relax. You can press this button as many times as you want and nothing bad will happen. It acts like a stress relief button 🙂
CELSIUS TO FAHRENHEIT
To change between °C and °F, while the heater is ON, press and hold the FLAME BUTTON on the control panel for 3 seconds.
OPEN WINDOW DETECTION
Should a window or door be accidentally left open for over 30 minutes, the heater will detect the sudden change in temperature and turn OFF automatically, displaying OP on the screen. To return to normal operation, press and hold the HEATER BUTTON for 3 seconds or turn the unit OFF and back ON.

AUTOMATIC HEATING SCHEDULE (AHS)

INTRODUCTION
You can set the heater to turn on/off at a specific temperature for specific times. You can set up to 7 different heating presets and individually assign to each one of them multiple days of the week.
A heating preset defines the start time, end time, room temperature and working days.
EXAMPLE:

• Preset 1 starts at 18:00 and stops at 22:00, temperature of 22°C, Monday to Friday
• Preset 2 starts at 10:00 and stops at 22:00, temperature of 22°C, Saturday and Sunday

SETTING THE PRESETS

There are 7 different presets that you can individually set. To begin setup for the first preset, during normal operation, press the OK BUTTON to activate the display and after that press the S

ETTING BUTTON :

• SET THE START TIME : The STATUS INDICATOR should show ON. Press the PLUS BUTTON to set the hour and the MINUS BUTTON to set the minutes.
• SELECT THE DAYS : Press the DAY BUTTON to navigate to a certain day and use the PLUS BUTTON to select it and the MINUS BUTTON to deselect it.
• SET THE TEMPERATURE: Press the HEATER BUTTON to set the temperature. Press the PLUS BUTTON to raise the temperature and the MINUS BUTTON to lower it.
• SET THE END TIME: Press the SETTING BUTTON to navigate to the end time. The
• STATUS INDICATOR should show OFF. Press the PLUS BUTTON to set the hour and the MINUS BUTTON to set the minutes.
• NAVIGATE TO NEXT PRESET: Use the SETTING BUTTON to navigate through the preset start time, preset end time and next preset.

ACTIVATING A PRESET

During normal operation, repeatedly press the DAY BUTTON on the remote to select the desired preset and press the OK BUTTON to activate it and the heating schedule will be set.

AUTO MODE

8 is the AUTO MODE. By selecting the 8 mode, all your presets will activate at the same time, one after the other. This mode is useful if you need multiple presets to run during the same day. NOTE: When using this mode, make sure the presets don’t have overlapping hours.

DEACTIVATING A PRESET

Press the CANCEL BUTTON to deactivate a preset and turn off the automatic heating schedule.

• NOTE : When using the automatic heating schedule manual heating and sleep timer will be disabled and will not work anymore until all presets have been deactivated.
• NOTE: The Automatic Heating Schedule (AHS) will work only if the clock has been set.
• NOTE: If there is a power outage or you unplug the firebox the system resets and you will have to set AHS all over again.

CONNECTING TO POWER

NOTE: A 13 amp, 240-volt circuit is required. A dedicated circuit is preferred but not essential. A dedicated circuit will be required if the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.
WARNING: Don’t use the firebox with regular extension cords. If the cord is not long enough you may use only special extension cords rated for a minimum of 13 Amps.

CARE AND MAINTENANCE

Make sure the unit is turned OFF and unplugged before cleaning the heater or fireplace. We recommend periodic vacuuming of the fan/heater. Remove dust with clean dry cloth. Remove fingerprints and other marks from glass screen by using a clean damp cloth. Do not use abrasive cleaners or spray liquids on the glass window surface.

REPLACING THE BATTERY

The remote control works with 2 x AAA 1.5 V standard batteries.

NOTE: Please always dispose of batteries at a suitable recycling point.

CAUTION:
Always purchase the right size and grade of battery most suitable for the intended use. Replace all batteries of a set at the same time. Clean the battery contacts and also those of the device before battery installation. Ensure the batteries are installed correctly with regard to polarity (+ and -). Remove batteries from equipment that is not to be used for an extended period. Remove used batteries promptly. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nicd, nimh, etc.) batteries. Do not ingest batteries.

MOUNTING THE FIREBOX

IN FURNITURE OR FIREPLACE MANTELS

NOTE: The exact furniture or mantel opening dimensions are: width 584 x height 495 (mm). When designing the opening, it is recommended to add a tolerance of + 3mm to the width and height.

CAUTION: For proper ventilation, leave 30mm minimum air space clearance between the back of the firebox and any other materials.

1. Insert the firebox from the back
2. Mount the securing plates on both sides of the firebox
3. Fix the plates using the included screws

IN WALL OR MASONRY FIREPLACES
NOTE : For all in-wall installations, we recommend using our TAGU 23RK1 Recessed Installation Kit (not included). The special frame provides proper airflow to the air intake vent and allows for easy fixing in walls or other constructions and removal of the firebox if the product should need to be sent back for warranty repairs.

A new outlet can be installed inside the framing construction. Plug the fireplace into a 13 Amp/240 Volt outlet. If the cord is not long enough you may use an extension cord rated for a minimum of 13 Amps. For detailed instructions on how to mount the firebox in wall, see the TAGU 23RK1 Recessed Installa-tion Kit’s instruction manual.

TECHNICAL DETAILS

Model identifier(s): 23PF1A, 23PF1B, 23PF1C, 23PF1D

Item| Symbol| Value Unit
Heat output
Nominal heat output| Pnom| 1,49 kW
Minimum heat output| Pmin| 6.042 x 10-3
Maximum continuous heat output| Pmax, c| 1,49 kW
Auxiliary electricity consumption
At nominal heat output| max| n/a kW
At minimum heat output| Amin| n/a kW
In standby mode| else| 10,245 x 10-3
Electronic room temperature control plus week timer| yes
Room temperature control, with open window detection| yes

• Rated Voltage: 220-240V
• Rated Frequency: 50 Hz
• Rated Power: 1260-1500W
• Protection against moisture: IP X0
• Protection Class: Class I
• Supply cord: 1.8 meters, non-detachable plug

DISPOSAL INFORMATION

For electrical products sold within the European Community. At the end of the electrical product’s useful life, it should not be disposed of with household waste. Please recycle where facilities exist. Check with a Local Authority or retailer for

recycling advice in your country.

FINAL INFORMATION

THIS PRODUCT COMPLIES WITH THE EUROPEAN SAFETY STANDARDS EN60335-2-30 AND THE EUROPEAN STANDARD ELECTROMAGNETIC COMPATIBILITY (EMC) EN 55014-1:2017, EN 55014-2:2015, EN 61000-3-2:2014 AND EN 61000-3-3:2013 THESE COVER THE ESSENTIAL REQUIREMENTS OF EEC DIRECTIVES 2014/30/EU

©PEFOC.RO SRL. ALL RIGHTS RESERVED. MATERIAL CONTAINED IN THIS PUBLICATION MAY NOT BE REPRODUCED IN WHOLE OR IN PART, WITHOUT PRIOR PERMISSION IN WRITING OF PEFOC.RO SRL.

MANUFACTURER & IMPORTER
PEFOC.RO SRL | PRINCIPALA 320, MOHU, SIBIU, ROMANIA, 557262

www.tagu.eu

References

• Support : Help Center
• Semineu pe lemne la preturi mici, seminee PeFoc rustice, moderne
• Europe's favourite fireplaces – TAGU
• Europe's favourite fireplaces – TAGU
• Product documents – TAGU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>