Metra DP-5859 Double DIN Dashboard Panel Instruction Manual

: June 4, 2024
: Metra

Table of Contents

KIT FEATURES
KIT COMPONENTS
TOOLS REQUIRED
APPLICATIONS
DASH DISASSEMBLY
KIT PREPARATION
KIT ASSEMBLY
Documents / Resources

Metra DP-5859 Double DIN Dashboard Panel Instruction Manual

Visit MetraOnline.com for more detailed information about the product and up-lo-date vehicle specific applications

KIT FEATURES

ODIN radio provisions. (sub-dash modifications are required)
Custom textured replacement dash panel to accommodate ODIN
radios. Metra suggests painting factory vents black to match the replacement dash panel.
Multiple trim panels and brackets to cover multiple trim levels and vehicle options.

KIT COMPONENTS

A) Dash panel ,
B) Manual climate panel
C) Manual climate brackets
D) Auto climate panel
E) Auto climate brackets
F) 3-position 4WD switch panel
G) 4-position 4WD
switch panel
H) Drive position switch back covers , I) Airbag switch panel
J) Blank panels (2)
K) Panel clips (5)
L) #4 x 3/8″ Phillips screws (4)
M) #8 x 3/8″ Phillips screws 06)

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: Please visit metraonline.com for wiring harness options.
Antenna Adapter: Not required

TOOLS REQUIRED

Panel removal tool
Phillips screwdriver
Socket wrench
Cutting tool

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

APPLICATIONS

Ford

Expedition ………………………………………….. .1997-2002
F-150 …………………………….. …………………….. 1997-2003
F-150 Heritage ………………………………………………. 2004
F-250 ……………………………………………………………. 1998

Lincoln

Blackwood …………………………………………………… 2002
Navigator …………………………………………….. 1997-2002

DASH DISASSEMBLY

Unsnap and remove the dash panel. (Figure A)
Remove the factory radio using Metra’s 86-5618 radio removal tools.
Remove the climate controls (recommended for sub-dash cutting). (Figure B)
Remove (2) 7/32″ screws and unsnap the factory vents from the dash panel. (Figure C)

If equipped, there Is a 3-position or a 4-positlon drive position switch. Remove switches from factory dash panel:
Remove 4wd knob from front. (Figure D)
(2) 5.5mm screws from the switch. (Figure D)
Grind down 3 tabs to remove the light pipe cover and drive position graphic with icons. Note: Be careful not to cut into the factory drive position graphic, it will be re-used along with the factory light pipe. (clear plastic) (Figure E)
Carefully remove the drive position graphic. (Figure E)
If equipped, remove the factory passenger airbag indicator and switch. (Figure F)

KIT PREPARATION

If equipped with the factory drive position switch:

Snap the drive position switch panel into place and secure with (2) factory screws (extra hardware is provided if needed). (Figure A)
Place the graphic into the drive position switch panel (either 3 position or 4 position). (Figure B)
Place the factory light pipe (clear plastic) into position and then the back cover. (Figure()
Secure the switch with the remaining factory screws ( extra hardware is provided if needed) Install the knob from the front. (Figure D)

If equipped with the factory passenger airbag switch:

Snap the airbag switch panel into place and secure with the factory hardware ( extra hardware is provided if needed). (Figure E)
Secure the factory switch into place using the factory hardware. (extra hardware is provided if needed). (Figure F)

Select either the manual climate or auto climate trim panel and brackets.

Secure the appropriate climate panel to the dash panel using the (4) supplied #4 x 3/8″ screws. (Figure G)
Attach the (5) supplied panel clips to the radio housing. (factory panel clips can be used) (Figure H)
Metra recommends painting the vents matte black to better match the replacement dash panel.
Attach the vents to the radio housing using the factory hardware (Figure I)
Cut sub dash area. Top and sides Remove rear support. Might need to trim the sub dash bracket (radio opening) (Figure J)
Install the climate controls back into the sub dash.

KIT ASSEMBLY

Attach the appropriate radio brackets to the radio using screws supplied with the radio, and then secure into the dash opening. (figure A)
Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
Snap the radio trim panel over the radio and reassemble the dash in reverse order of disassembly.

Having difficulties? We’re here to help.

Contact our Tech Support line at:
386-257-1187

Or via email at:
techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)

Monday -Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM -7:00 PM
Sunday: 10:00 AM -4:00 PM

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow.

Metra recommends MO certified technicians

Documents / Resources

| Metra DP-5859 Double DIN Dashboard Panel [pdf] Instruction Manual
DP-5859, Double DIN Dashboard Panel, DP-5859 Double DIN Dashboard Panel, DIN Dashboard Panel, Dashboard Panel, Panel
---|---