Bestier H1023145AUS Electrical Desk Instruction Manual

H1023145AUS Electrical Desk

V001-110823-01
Electrical Desk
H1023145AUS 

ASSEMBLY INSTRUCTION

HELPFUL HINTS

BEFORE YOU START

• Inspect product packaging to ensure the appearance is good.
• Read the assembly instruction carefully and follow it step by step.
• To avoid any scratching, putting a soft blanket on the floor is suggested.
• Identify, sort and count all the parts with tags.
• Find out installation position according to the drawing and install it in correct steps.

OTHER
People needed for assembly: 1-2.
Estimated assembly time: 0.5-1h.
CAUTION
Be cautious when using a power drill or power screwdriver.
Please be aware to slow down and stop when screw is nearly tight.
Do Not use any harsh chemicals or abrasive cleaners for this item.
Push, pull or drag this item carefully.

USER MANUAL Power Input 100V-240V
Speed 20 mm/s
Motion Noise＜55dB
Load Capability 154 lbs / 70 kg

• 3 Height Position Memory
• Vertical Range: 72-118cm
• Desk top Dimensions: 95-135cm

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY.SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

DETAILS

UNIT:INCH/CM

PART LIST

Part #1~Part #10 are positioned in the packing box of the base.
※Please follow the instruction for installation and ignore the instruction in the packing box of the base.

ACCESSORY LIST

The above hardware accessories are positioned in the packing box of the base. Loosen the knob Insert the transmission rod into the hex hole and turn thetransmission rod clockwise until the left leg goes to the lowest position. Insert the other end of transmission rod to the slot on the leg (You may rotate the rod slightly for better installation).Secure the transmission rod to the slot by tightening the pre-assembled set screw using the small Allen key. Tighten the knob

USING THE CONTOLLAR

| Short-press the button, and the display will flash. Press the , , or button to save the current height setting to that button.
---|---
| Press the Boutton, and the desk will move to the height that was previously set for that button.
| Press the button, and the desk will move to the height that was previously set for that button.
| Press the button, and the desk will move to the height that was previously set for that button.
| Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.
| Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings

Change Display Height Units| Press and hold the button until a flashing’S-‘is displayed. Press again, and’Un’is displayed. Press to select it, press or to switch between’IN'(imperial) and ‘S1’ (metric), and press to save your choice.
---|---
 Change Collision Detection Sensitivity| Press and hold the button until a flashing’S-‘is displayed. Press again, and’Un’is displayed. Press or to switch to’CF’and press to select it. Press or to switch between off, low, normal, and high sensitivity. Press to save your choice.
Reset|  Press and hold the button for 5 seconds, and the screen will show’RES.’Continue holding until the desk goes down to I its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 5 minutes,
it will stop operating to prevent damage from overheating. Wait for at least 15 minutes before making any further height adjustment.
---|---
EIO| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

CUSTOMER SUPPORT

North American
888-666-1086
Service.US@bestier.net
Global
Service@bestier.net
Europe
Service.UK@bestier.net
Service.FR@bestier.net
Service.ES@bestier.net
Service.DE@bestier.net
Service.IT@bestier.net
0755-26917626
Asia
04-8888-0283
Service.JP@bestier.net
sskj@bestier.net

Love coming home.
Comfort Zone Co.,Limited
RM1903 19F BeiYou technology Building, Yuehai Street
No.42 Gaoxin South Ring Road,Nanshan,Shenzhen

Documents / Resources

| Bestier H1023145AUS Electrical Desk [pdf] Instruction Manual
V001-110823-01, H1023145AUS, H1023145AUS Electrical Desk, Electrical Desk, Desk
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>