phocos AB-PLC Monitoring and Control Gateway User Manual

: June 4, 2024
: phocos

Table of Contents

phocos AB-PLC Monitoring and Control Gateway
Introduction
Important Safety Information
About the Any-Bridge AB-PLC
Installation
LED Indicators
Troubleshooting
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

phocos AB-PLC Monitoring and Control Gateway

phocos-AB-PLC-Monitoring-and-Control-Gateway-product

Introduction

Dear customer, thank you for choosing this quality Phocos product. The Any- Bridge™ AB-PLC Monitoring & Control Gateway (referred to as “gateway” in this manual) allows you to connect your Phocos AnyGrid™ PSW-H Series inverter/charger with MPPT solar charge controller (referred to as “power device” in this manual) to the internet for access to the PhocosLink Cloud portal (referred to as “portal” in this manual). This portal enables viewing and control (functionality enabled by a future over-the-air automatic update, no user intervention required) of your power device through any internet- connected device with an internet browser such as a personal computer, tablet or smartphone. The purchase of this device enables free introductory access to the PhocosLink Cloud with up to three Any-Grid PSW-H devices for a limited time, see www.phocos.com for details regarding access plans. This manual describes the installation and operation of this unit. Read this entire document before proceeding with the installation.

Important Safety Information

SAVE THESE INSTRUCTIONS : This manual contains important instructions for the model AB-PLC in the Any-Bridge Series. Read and save this manual for future reference. The following words are used to mark important sections for your safety:
WARNING Failure to follow instructions could cause physical harm. It is not necessary to open any covers or access any high voltage components in the power device for installation.
The power device may only be opened by trained electricians.

About the Any-Bridge AB-PLC

A working internet connection is required for the gateway to be able to communicate with the PhocosLink Cloud portal and upload data regularly. However, in case of internet access interruption, data is stored in the gateway until the internet connection is re-established, then this data is seamlessly sent to the portal to fill any data gaps caused by the internet interruption (functionality enabled by a future over-the-air automatic update, no user intervention required).

MXI interface (unused at this time)
RS-485 interface (unused at this time)
RS-232 interface for Any-Grid PSW-H
Power indicator
Portal connectivity indicator
Reset button for factory reset
Ethernet LAN interface
Wi-Fi / BLE antenna

WARNING : The gateway is designed to be powered by the connected power device. No external power supply is required. Attempting to power the gateway with an external power supply may cause physical harm or damage/destroy the gateway.

Installation

Requirements
- Phocos Any-Bridge AB-PLC monitoring & control gateway
- One to three powered Any-Grid PSW-H power devices with U2 firmware version ≥ 06.16
- Working internet infrastructure (modem/router with active DHCP for automatic IP address issuing) with Ethernet and/or 2.4 GHz 802.11b/g/n Wi-Fi access
- Android™ or iOS device with BLE V4.2 or higher

Package Contents
Before installation, please inspect the unit. If something inside the package is missing or damaged, please contact your dealer. Package contents:

Any-Bridge AB-PLC monitoring & control gateway
External antenna
Cable with 8P8C modular connectors at each end
User and installation manual

Physical Installation
Lightly screw the included antenna into the antenna connector at position ⑧, ensuring it is less than hand-tight to avoid damage. Either place the gateway on a flat surface as pictured in the title image of this manual. Alternatively, mount the gateway on a vertical wall by using the 4 pcs. M3-sized (3.5 mm / 0.14 in) screw-holes provided. Once installed, point the antenna so that it runs parallel to your router antenna or, if in doubt, point it straight up vertically.

Setup
For a video to help with the installation visit www.phocos.com/phocoslink- cloud. Choose any of the power devices and connect the included cable with 8P8C connectors (any direction) between the RS-232 port of the power device and the ③ RS-232 port of the gateway. Ensure the power device is not in standby and that its display is on. The power ④ and portal connectivity ⑤ indicators will blink several times while the gateway starts up (see chapter 5 for details). If using wired Ethernet, connect the Ethernet cable from your router to port ⑦ of the gateway. Download the latest “PhocosLink Mobile” App from the Google Play™ store or Apple’s App Store® with an Android™ or iOS device, respectively. Open the app and allow BLE and location permission (location is not recorded or used by the app, but access must be permitted for BLE to function). The QR codes left and right link to the app directly.

In the app, scan for devices with the button at the bottom right and then tap the Any-Bridge™ gateway:

Ensure the connection between the power device and gateway is not greyed out (the power device is shown as connected) and the solid-state relay is shown as “closed” (green). If it is not, go back to the previous screen (arrow at top left) and try again by tapping the Any-Bridge. phocos-AB-PLC-Monitoring-and-
Control-Gateway-fig-5

Then tap “SETUP”. Enter your credentials:

Wi-Fi Access Point (SSID) and W-Fi password (only shown if no Ethernet cable is plugged in)
PV system name as it will be shown on the portal

Once submitted, wait for each of the steps to automatically complete with a (except the “Wi-Fi” steps if using wired Ethernet), this may take a few minutes, then tap “DONE” when completed and the activation e-mail is successfully sent. You will now receive an invitation to the e-mail address you provided with your access link to the PhocosLink Cloud, select “Accept Invitation”. This will lead you to the PhocosLink Cloud website to finalize your initial setup. If you do not receive the e-mail within 5 minutes, check your e-mail spam folder. If you still did not get the email, go to cloud.phocos.com and select “Forgot your password?”.
Then enter the same e-mail address you used previously and select “Send reset email”.
The initial setup is now complete, and the gateway automatically sends data to the PhocosLink Cloud continuously while the internet connection is active as shown by indicator ⑤. While connected to the gateway with the “PhocosLink Mobile” app, the 4 green (connected) or grey (disconnected) toggle icons give you a view of the working state of the gateway at any time while it is running (example shown with Wi-Fi):

LED Indicators

The gateway is equipped with two LED indicators, the power ④ and the portal connectivity ⑤ indicators. During operation, these indicators have the following meanings:

Power

④

| Portal con.

⑤

| ****

Meaning

---|---|---
OFF| n/a| Gateway is not powered. This is normal if the

power device is in stand-by (display off)

ON| n/a| Gateway is powered and power device

communication successful

Slow

blink*

| n/a| Gateway is powered and a BLE device is

connected

n/a| ON| Connected to portal
n/a| OFF| Disconnected from portal
ON| Slow

blink*

| Connected to Wi-Fi or Ethernet, but portal

connection unsuccessful

Slow

blink*

| Slow

blink*

| Gateway starting up or power device

firmware incompatible if blinking for >10s

Troubleshooting

Problem| What to do
Power indicator ④ OFF| Gateway is not powered. Use only the included cable for connection between power device and gateway. Check the cable for correct seating on both ends. Ensure the power device

is running (power device display on).

Power ④ and

Portal con. ⑤

| The firmware on the power device is not

compatible with the gateway. Contact your

indicator| dealer or Phocos for a firmware update. A
blinking| standard USB to RS-232 converter and
slowly > 10s| Windows PC is required for the update.
Power ④| If using Wi-Fi, the entered access point (SSID) or
indicator ON| password is incorrect or the access point is not
and Portal

con. ⑤

| using WPA-PSK2 encryption. To re-enter Wi-Fi

credentials, press the reset button ⑥ until the

Warranty

Conditions
We warranty this product against defects in materials and workmanship for a period of 24 months from the date of purchase and will repair or replace any defective unit when directly returned, postage paid by the customer, to Phocos. This warranty will be considered void if the unit has suffered any obvious physical damage or alteration either internally or externally. This warranty does not cover damage arising from improper use, such as plugging the unit into unsuitable power sources, or attempting to operate products that require excessive power consumption or use in unsuitable environments. This is the only warranty the company makes. No other warranties express or implied including warranties of merchantability and fitness for a particular purpose. Repair and replacement are your sole remedies and the company shall not be liable for damages, whether direct, incidental, special, or consequential, even if caused by negligence. Further details about our warranty conditions can be found at www.phocos.com.

Liability Exclusion
The manufacturer shall not be liable for damages, especially on the battery, caused by use other than as intended or as mentioned in this manual or if the recommendations of the battery manufacturer are neglected. The manufacturer shall not be liable if there has been service or repair carried out by any unauthorized person, unusual use, wrong installation, or incorrect system design. Specifications are subject to change without notice.