FIRECORE F94T-XG Green Line Laser User Manual

June 17, 2024
Firecore

FIRECORE F94T-XG Green Line Laser

FIRECORE F94T-XG Green Line Laser 

Please read these instructions before operating the product

Symbol Safety Instructions

Working safely with the measuring tool is possible when the operating and safety information are read completely and the instructions contained therein are strictly followed. Never make warning labels on the measuring tool unrecognizable. Save these instructions for reference.

WARNING

LASER RADIATION. Do not stare into beam. Class II laser product. Turn the laser beam on only when using this tool.
Symbol

  • Do not operate the laser in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
  • Use the laser only with the specifically designated batteries. Use of any other batteries may create a risk of fire.
  • Store idle laser out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained users.
  • Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Do not use optical tools such as a telescope or transit to view the laser beam. Serious eye injury could result.
  • Do not place the laser in a position which may cause anyone to intentionally or unintentionally stare into the laser beam. Serious eye injury could result.
  • Do not position the laser near a reflective surface which may reflect the laser beam toward anyone’s eyes. Serious eye injury could result.
  • Turn the laser off when it is not in use. Leaving the laser on increases the risk of staring into the laser beam.
  • Do not modify the laser in any way. Modifying the tool may result in hazardous laser radiation exposure.
  • Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.
  • Do not remove or deface warning labels. If labels are removed user or others may inadvertently expose themselves to radiation.
  • Position the laser securely on a level surface. Damage to the laser or serious injury could result if the laser falls.

Safety Instructions

Product Overview

Product Overview

Control Panel

V/Anti-shock—- Control the vertical lines/anti-shake mode
H/Manual—Control the horizontal lines/manual mode
Receiver—Pulse mode

Product Overview

Battery Charging / Installation

Product Overview

Warning

  • The battery may explode or leak, and as a result, it may cause personal injury and fire.
  • To reduce such risks, please strictly follow all instructions and warnings on the battery label and plug.
  • Do not mix battery compounds while assembling the battery.
  • Do not put the battery into the fire.
  • Always keep the battery away from children
  • Do not dispose of this product as household waste.
  • Batteries should be disposed of in accordance with local waste disposal regulations
  • Please follow the local WEEE directive for collecting and processing electrical and electronic waste.

Operating Modes

Self-leveling Mode

Press or slide locking switch to turn the laser tool ON. Self-leveling is enabled when the laser tool is switched to unlocked position. This laser tool projects one horizontal beam and two vertical beams with automatic leveling range of ±4º. Once the leveling is finished, the laser beams won’t flash anymore. Short press operation button to switch the laser line combinations in turn.

Manual Mode

When the pendulum lock is in its locked position, short press and hold the “Manual” key for about 3 seconds until the laser beam appears, the laser line flashes every 5 seconds. In manual mode, the laser tool won’t be self- leveling. It could be held by hand or placed on an inclined surface to project a bright laser beam in any direction.

Anti-shake Mode

Slide locking switch to turn the laser tool ON, press and hold the “Anti- shake” key for about 3 seconds, the indicator flashes 3-5 times until stop flashing and then enter the anti-shock mode. At this time, if the laser tool is tilted, then no matter press any button, the laser line will not light up, this mode can be turned off by slide locking switch to OFF position, or press and hold the “Anti-shake” button for more than 3 seconds.

Pulse Mode

How to use the Firecore laser receiver with F94T-XG laser level? First, turn on laser level’s pulse mode——Press the “Receiver” button, the straight laser line stops flashing and then enters the pulse mode. Secondly, turn on the receiver and detect the laser lines. When the receiver detects the laser lines, it will make “Beep” sounds.

Specifications

Model F94T-XG
Laser Line 12 Green Lines
Leveling Type Gravity Pendulum
IP Rating IP65
Laser Class Class 2 (IEC/EN 60825-1:2014), <1mW power output
Overall Accuracy ±3mm/10m (±1/9 inch/33Ft)
Leveling Range ±4°
Working Distance 25m
Used with Receiver 2-60m
Laser Wavelength 510nm-520nm
Battery Capacity 2600mAh
Reference Operation Time Approximately 10 Hours
Mount Size 1/4”
Operation Temperature Range -10℃ to 50℃
Storage Temperature Range -20℃ to 60℃

Maintenance

This 3×360° Self-leveling Line Laser has been designed to be a low maintenance tool.However, in order to maintain its performance, you must always follow these simple directions:

  • Avoid exposing the tool to shock, continuous vibration or extreme hot or cold temperature.
  • Always store the tool indoors.
  • Always keep the tool free of dust and liquids. Use only a clean, soft cloth for cleaning. If necessary, slightly moisten the cloths with pure alcohol or a little water.
  • Do not disassemble the self-leveling 360-degree cross line laser; this will expose the user to hazardous radiation exposure.
  • Do not attempt to change any part of the laser lens.
  • Remove the battery from the tool and store it in a cool dry location.
  • After you have finished using the tool, always make sure that the switch is in the OFF position.

Troubleshooting

PROBLEM CAUSE SOLUTION
The laser line is hard to see. The laser tool is too far from the target.

Move the tool closer to the target.
The surrounding is too bright.| Switch to receiver(pulse) mode and find the laser line with FD30 laser receiver (sold separately).
Laser line is not projected.| No battery installed or battery is depleted.| Install battery or charge the battery.
The power switch is not pushed to the “ON” position.| Slide the power switch to the “ON” position.
Laser line flickers for alert.| The surface where the tool has been placed is uneven or the tool is out of its automatic self- leveling range.| Place the tool on a more level surface (within ±4°).

Warranty

for professional users. This statement is in addition to and in no way prejudices your contractual rights as a professional user to your statutory rights as a private non-professional user. We warrant our laser level(s) against faults in materials and/or workmanship for one year from the date of purchase, provided that:

  • Proof of purchase is produced;
  • Service/repairs have not been attempted by unauthorized persons;
  • The product has been subject to fair wear and tear;
  • The product has not been misused;
    Defective products will be repaired or replaced, free of charge or at our discretion, if sent together with proof of purchase to our authorized distributor(s.)

This Warranty does not cover faults caused by accidental damage, unfair wear and tear, and use other than in accordance with the manufacturers’ instructions or repair or alteration of this product not authorized by us. Repair or replacement under this Warranty does not affect the expiry date of the Warranty.

  • Customer is responsible for the correct use and care of the tool. Moreover customer is completely responsible for periodically checking the accuracy of the laser, and therefore for the calibration of the tool.
    You can enjoy 12 months limited warranty but up to 24 months longer warranty if you sign up as a member through the product registration. Please scan the QR code above to activate your priority.
    QR Code

Customer Support

 Questions, problems, missing parts? Before returning to your retailer, contact us by email: support@Firecoretools.com.

Symbols

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals