Max Pro Fade 2.0 Cordless Hair Clipper User Manual
- June 17, 2024
- MAX PRO
Table of Contents
Max Pro Fade 2.0 Cordless Hair Clipper
Specifications:
- Max Pro stainless steel blades
- Blade adjustment lever
- On/Off switch
- LED display
- Clipper adjustments (3mm, 6mm, 9mm, 12mm)
- Blade Lubricant
- Cleaning Brush
- Charging Base + Cord
Product Usage Instructions
Applying Lubricant to the Blade:
Before use, drop a bit of lubricant between the edge of the blade and the
blade itself. Open the switch to let the electric trimmer run for a few
seconds before using it.
Checking and Adjusting Cutting Blade:
Ensure the upper and lower teeth of the cutting blade fit properly. If broken
or misplaced, remove and reinstall the cutting blade before use.
Cord/Cordless Operation:
For reliable power throughout the day, the clipper can be used corded or
cordless. If the clipper powers off during use, attach the adapter cord for
continuous corded operation.
Using Attachment Combs:
Simply slip the cutter blade teeth into the comb and snap it down. The length
of the trim is indicated on the attachment comb. To remove, snap off.
Adjusting Blade Set:
To ensure correct alignment:
- Push the blade adjustment lever forward.
- Ensure proper clearance distance between moving and fixed blades.
- Check alignment points as described in Figure A.
- If alignment is incorrect, adjust the bottom blade screws as described.
- Tighten screws once blades are correctly aligned.
Care and Servicing Blades:
Oil the blades before, during, and after each use. Apply a few drops of
Clipper Oil on the front and side of the cutter blades if streaking or slowing
down occurs.
Replacing Shaving Blades:
- Unscrew to remove both blades.
- Replace with new blades by angling the cutting blade into position and pushing it down to click into place.
- Hold the top blade in place and secure by screwing it back.
Charging:
The clipper uses a lithium-ion battery with an input voltage of 5V 1A.
- Charge for 2 hours before first use for maximum performance.
- Fully charged clipper provides up to 200 minutes of run time.
- The red light indicates charging status – ON when charging, OFF when fully charged.
FAQ:
-
Q: How often should I oil the blades?
A: The blades should be oiled before, during, and after each use. If streaking or slowing down occurs, it’s time to oil them. -
Q: What should I do if the clipper powers off during use?
A: You can attach the adapter cord for corded operation to continue using the clipper. Remember, it will not charge while in use with the cord attached.
INSTRUCTIONS
- Apply lubricant to the blade: Before use, drop a bit of lubricant between the edge of the blade and the blade itself, then open the switch to let the electric trimmer run for a few seconds before using.
- Before you start, check if the upper and lower teeth of the cutting blade fit properly. If the upper and lower teeth are broken or misplaced, remove the cutting blade and reinstall it before use.
OVERVIEW
- Max Pro stainless steel blades
- Blade adjustment lever
- On/Off switch
- LED display
- A. Clipper adjustments. (3mm, 6mm, 9mm, 12mm)
- B. Blade Lubricant.
- C. Cleaning Brush
- D. Charging Base + Cord
HOW TO USE
- Cord/Cordless operation for reliable power to last you all day long.
- Corded operation: If the clipper powers OFF in the middle of a clipping job, the adapter cord can be attached to continue use in corded operation. The clipper will not charge while in use with the cord attached.
- Using the attachment combs: simply slip the cutter blade teeth into comb and snap the comb down. To remove simply snap off. The length of trim is indicated on the attachment comb
ADJUSTING BLADE SET
To ensure the blades are still correctly aligned
- Push the blade adjustment lever forward. The top moving blade tips should be 0.5mm to 1.0mm behind the tips of the fixed bottom blade. This clearance distance is important to prevent cuts during use. (Point in Figure A)
- The extreme left-hand tooth of the top moving blade must be covered or be to the left of the first small tooth of the fixed bottom blade. (Point 2 in Figure A)
- The extreme right-hand tooth of top moving blade must be touching the big tooth on the fixed bottom blade. (Point 3 in Figure A)
- If the blade alignment is incorrect, turn the clipper off and unplug from the electrical outlet. 5. Slightly loosen the two screws on the bottom blade and adjust to the setting described in step 1.
- Once the blades are correctly aligned, tighten the screws.
Taper Lever
The adjustable clipper blade set is easy to adjust. From coarse to fine cuts,
all that is needed is a flick of the adjustment lever with your thumb. In the
upright position, the blades are set for the finest, or shortest cuts (Figure
D).
Care and Servicing Blades
The blades should be oiled before, during, and after each use. If your clipper
blades leave streaks or slow down, it’s a sure sign the blades need oil. Place
a few drops of Clipper Oil on the front and side of the cutter blades( Figure
E).
REPLACING THE SHAVING BLADES
- Firstly, unscrew to remove both blades.
- Replace the clipper with new blades, angle the new cutting blade into position, and push down to click it into place.
- Hold the top blade in place and screw it until secure
CHARGING
The clipper is intended for use with a lithium-ion battery with an input voltage of 5V 1A.
-
Please charge the clipper for 2 hours before FIRST use for maximum performance.
When the battery is fully charged, the clipper can be used for up to 200 minutes of run time. -
The red light on the clipper will turn ON when the clipper is charging. When the clipper is fully charged, the red light becomes to green.
-
Charged over time, the battery life may be reduced.
-
It can be charged when battery power shortage or long time no use. It will affect battery performance when enough power to charge.
ENVIRONMENT
Correct disposal of this product: This mark indicates that this product should
not be disposed of with other household wastes throughout the EU. To prevent
possible harm to the environment or human health,
please recycle it responsibly to promote the sustainable reuse of material
resources
IMPORTANT
- Regularly apply lubricant between the blade and the cutting blade to keep the blade sharp, reduce operational noise, and extend the lifespan of the blade.
- The device should not be exposed to moisture.
- The device should be operated by hand. Turn off the switch when not in use to prevent accidents.
- Before storing, clean the hair from the blade, then drop a bit of lubricant and install the cutting blade with the protective cap.
- The safe factory current of the device is approximately 70% and can be used after it is fully charged.
To reduce the risk of electric shock and fatal injuries:
- Do not reach for an appliance that has fallen into the water. Unplug immediately.
- Do not use it while bathing or in a shower.
- Do not place or store appliances where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- Except when charging, always unplug this appliance from the electrical outlet immediately after use.
- Unplug this appliance before cleaning, putting on or taking off parts.
WARNING
To reduce the risk of burns, electric shock, fire, or injury to persons:
- An appliance should never be left unattended when it is plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or invalids.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Always switch off this appliance after using it.
- Never drop or insert any object into the opening.
- Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered.
- Do not use this appliance with a damaged or broken comb or blade, as cut or scratched skin may occur.
- Do not wrap the cord around the unit when storing Continuous stress on the cord can damage cord insulation and result in a shock hazard.
- Avoid contact with moving blades.
- This appliance is for cutting purpose use only Keep this appliance dry.
- Keep this appliance dry.
- This appliance is not intended for use by persons (including children )with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
WARRANTY
- The warranty on this product is valid for two years from the date of purchase.
- Please keep your proof of purchase (receipt, order confirmation email) and the original box of your styling tool as proof of purchase. This warranty is only valid for tools purchased from an authorized Max Pro retailer.
- If your product fails to function properly due to a manufacturer’s defect and the warranty conditions are met, your Max Pro styling tool will be repaired or replaced; this is determined by the manufacturer.
- This warranty does not apply to problems resulting from misuse, damage or normal wear and tear; the warranty is void if the product is used for commercial purposes. In addition, the warranty does not apply to styling tools that have been modified or repaired by an unauthorized Max Pro retailer or manufacturer.
- For warranty questions, please contact our Customer Service or visit us at www.maxprohair.com. If the product does not function properly, we will require digital photos of the product, as well as a copy of your original proof of purchase. In case of replacement or repair, a payment is required to cover the shipping and handling costs (depending on where you live). Feel free to contact us if you have any questions or comments.
- We are happy to help you!
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>