AVERTX DP15IR Indoor Outdoor Bullet Camera User Manual

: June 17, 2024
: AVERTX

Table of Contents

REGULATORY COMPLIANCE
GENERAL SPECIFICATIONS
BOX CONTENTS
INSTALLATION
CAMERA OSD MENU
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AVERTX DP15IR Indoor Outdoor Bullet Camera

Please carefully read these instructions before using this product. Save this document for future use. 31543AA

REGULATORY COMPLIANCE

Emissions FCC part 15, subpart B, Class A CE: EN61000-6-4:2007
Immunity CE: EN60130-4:1995 + A1:1998 + A2:2003

FCC COMPLIANCE

This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipments operated in a commercial environment. The product generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference in a non-residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with the radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the antenna of the radio/television receiver.
Increase the separation between this equipment and the radio/television receiver.
Plug the equipment into a different outlet so that the equipment and the radio/television receiver are on different power mains branch circuits.
Consult the dealer or an experienced radio/television technician for additional suggestions.

GENERAL SPECIFICATIONS

Model No.	DP15IR	DP15IRV
Image Sensor	1/3” Sony CCD
IP Rating	IP66
Type / Format	NTSC
Wide Dynamic Range	Digital Wide Dynamic Range
Minimum Illumination	0.1 Lux @ F1.2, 0 Lux with LEDs engaged
Day / Night	Digital Day / Night
Resolution	650 TVL
Focal Length	4mm Fixed	4mm ~ 9mm Varifocal Lens
Iris Control	Auto
Auto White Balance Range	2500K ~ 9500K
Backlight Compensation	Yes
Auto Gain Control	Auto
Operating Temperature	14˚ ~ 122˚ F (-10˚ ~ 50˚C)
Heater	No
Power Consumption	6.6W Max
Input Voltage	12vDC
Weight	1.9 lbs (0.9 kg)
Dimensions	W: 4.1” (105mm) x H: 4.1” (105mm) X L: 8.9” (226mm)*
Housing	Gray

Width, Height, and Length measurements include mount and sunshield.

Precaution

Please study the user manual before installation and keep the manual for future reference.
Avoid shining the LED lights directly in eyes.
Do not install the camera on an unstable surface.
To avoid fire or electric shock, use a proper power source.
Do not disassemble the camera.
Stop using the camera if you see smoke or feel unusual heat.
Do not cut or peel the covering away from the cable. This will eliminate weather protection and void the warranty.

Features

650 TV-Line Resolution
Digital Wide Dynamic Range
IR LEDs
IP66-rated

BOX CONTENTS

Screws (x4)
Anchors (x4)
Hex-head wrench
Sun visor screw
Extra video output cable

DIMENSIONS

INSTALLATION

Wall or Ceiling

Drill a 1” hole in the wall or ceiling for the cable.
Drill four 1/4” holes and insert the included anchors.
Attach the cables and tighten the included screws to mount the camera to the wall or ceiling.
Attach the sun visor using the included sun visor bolt.
Use the included 3mm hex-head wrench to loosen the adjustment bolt.
Aim the camera and tighten the bolt to complete the installation.

FUNCTION SETTING

Push the lever to access the menu and confirm selection. Push the lever for one second to open or close the menu. Use the lever to return to the previous menu from motion detection or privacy mask setting sections.
Use a screwdriver to adjust the focus.
Use a screwdriver to adjust the zoom.
Plug a test monitor into the optional VIDEO terminal to view menu screens during installation.
The debug port is used for product upgrades. This should only be accessed by a trained technician.