Shelly Wave 1 Electrical Switch Smart Switch Blue A User Manual
- June 17, 2024
- Shelly
Table of Contents
Shelly Wave 1 Electrical Switch Smart Switch Blue A
USER AND SAFETY GUIDE
Z-Wave® smart switch with potential-free contacts
READ BEFORE USE
This document contains important technical and safety infor-mation about the
Device, its safe use and installation.
CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents ac-companying the device. Failure to follow the installation proce-dures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or dam-age in case of incorrect installation or improper operation of this Device due to failure of following the user and safety instructions in this guide.
TERMINOLOGY
Gateway – A Z-Wave® gateway, also referred to as a Z-Wave® controller,
Z-Wave® main controller, Z-Wave® primary controller, or Z-Wave® hub, etc., is
a device that serves as a central hub for a Z-Wave® smart home network. The
term “gateway” is used in this document.
S button – The Z-Wave® Service button, which is located on Z-Wave®
devices and is used for various functions such as in-clusion (adding),
exclusion (removing), and resetting the device to its factory default
settings. The term “S button” is used in this document.
Device – In this document, the term “Device” is used to refer to the
Shelly Qubino device that is a subject of this guide.
ABOUT SHELLY QUBINO
Shelly Qubino is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits with a smartphone, tablet, PC, or home automation system. They work on Z-Wave® wireless communication protocol, using a gateway, which is required for a configuration of the Device. When the gateway is connected to the internet, you can control Shelly Qubino devices remotely from anywhere. Shelly Qubino devices can be operated in any Z-Wave® network with other Z-Wave® certified devices from other manufacturers. All mains operat-ed nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Devices are designed to work with older generations of Z-Wave® devices and gateways.
ABOUT THE DEVICE
The Device controls the on/off function for one electrical appliance, e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. The output contact is po-tential-free (dry contact), so different power supply loads (up to 15 A) can be connected to the Device. It is compatible with push-buttons and switches (default).
INSTALLATION INSTRUCTIONS
The Device can control a various type of loads (e.g., bulbs) in one electrical
circuit up to 15 A. It can be retrofitted into stan-dard electrical wall
boxes, behind power sockets and light switches or other places with limited
space.
For the installation instructions, refer to the wiring schemes (Fig. 1-3) in
this user guide.
-
⚠CAUTION! Danger of electrocution. Mounting/installation of the Device to the power grid has to be performed with caution, by a qualified electrician.
-
⚠WARNING! Danger of electrocution. Every change in theconnections has to be done after ensuring there is no voltage present at the Device terminals.
-
⚠CAUTION! Use the Device only with a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.
-
⚠CAUTION! Do not connect the Device to appliances exceeding the given max. load!
-
⚠CAUTION! Do not shorten the antenna.
-
⚠RECOMMENDATION: Place the antenna as far away aspossible from metal elements as they can cause signal interference.
-
⚠CAUTION! Connect the Device only in the way shown inthese instructions. Any other method could cause damageand/or injury.
-
⚠CAUTION! Do not install the Device where it can get wet.
-
⚠CAUTION! Do not use the Device if it has been damaged!
-
⚠CAUTION! Do not attempt to service or repair the Deviceyourself!
-
⚠RECOMMENDATION: Connect the Device using solid single-core wires with increased insulation heat resistance notless than PVC T105°C (221°F).
-
⚠CAUTION! Before starting the mounting/installation of the Device, check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase tester or multimeter.
When you are sure that there is no voltage, you can proceed to connecting the wires. -
⚠RECOMMENDATION: For inductive appliances that causevoltage spikes during switching on/off, such as electrical motors, fans, vacuum cleaners and similar ones, RC snubber (0.1 μF / 100 Ω / 1/2 W / 600 VAC) should be connected parallel to the appliance.
-
⚠CAUTION! Do not allow children to play with the push-buttons/ switches connected to the Device. Keep the devices for remote control of Shelly Qubino (mobile phones, tablets, PCs) away from children.
EXTENDED USER GUIDE
For more detailed installation instructions, use cases, and comprehensive guidance on adding/removing the Device to/from a Z-Wave® network, factory reset, LED signalization, Z-Wave® command classes, parameters, and much more, refer to the extended user guide at: https://shelly.link/Wave1-KB-US
SPECIFICATIONS
Power supply| 110-240 V AC / 24-48 V DC /
12 V DC ± 10%
---|---
Power consumption| < 0.3 W
Max. switching voltage AC| 240 V
Max. switching current AC| 15 A
Max. switching voltage DC| 30 V
Max. switching current DC| 10 A
Overheating protection| Yes
Distance| Up to 40 m indoors (131 ft.) (depends on local condition)
Z-Wave® repeater| Yes
CPU| Z-Wave® S800
Z-Wave® frequency bands| 908,4 MHz
Maximum radio frequency power transmitted in frequency band(s)| < 25 mW
Size (H x W x D)| 37x42x16 ±0.5 mm /
1.46×1.65×0.63 ±0.02 in
Weight| 26 g / 0.92 oz.
Mounting| Wall console
Screw terminals max. torque| 0.4 Nm / 3.5 lbin
Conductor cross section| 0.5 to 1.5 mm² / 20 to
16 AWG
Conductor stripped length| 5 to 6 mm / 0.20 to 0.24 in
Shell material| Plastic
Color| Blue
Ambient temperature| -20°C to 40°C / -5°F to 105°F
Humidity| 30% to 70% RH
Max. altitude| 2000 m / 6562 ft.
DISPOSAL & RECYCLING
This refers to the waste of electrical and electronic equipment. It is applicable in the US and other countries to collect waste separately.
This symbol on the product or in the accompanying liter-ature indicates that the product should not be disposed of in the daily waste. Wave 1 must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources. It is your responsibility to dispose of the device separately from general household waste when it is already unusable.
FCC NOTES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must ac-cept any interference received, including interference that may cause undesired operation. The manufacturer is not respon-sible for any radio or TV interference caused by unauthorized modification or change to this equipment. Such modifications or change could void the user’s authority to operate the equip-ment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment andreceiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ORDERING CODE: QNSW-001X16US
MANUFACTURER
Shelly Europe Ltd.
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Web: https://www.shelly.com
Changes in the contact data are published by the Manufacturer at the official
website: https://www.shelly.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>