Calefactive D2 Space Heater Instruction Manual

Calefactive D2 Space Heater

Read and Save These Instructions
Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by obseeine il inter informations supree col hat. thin seattis ued restine on. is no intender pere damage commercial, industrial or agricultural settings.

WARNING

IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons:
Read all instructions before using this Heater.

WARNING

• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.

• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.

• Make certain that the power source conforms to the electrical requirements of the Heater.

• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended.
  Never leave children unattended when the Heater is on or plugged in.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
  Do not attempt to defeat this safety feature.

• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.

• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
  To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.

• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.

• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the Heater. Always unplug the power cord.

CAUTION

• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.

• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.

• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
  This Heater iS not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined, Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or stan- dards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.”

Parts Included

NOTE: The component is operating at high temperatures and is not allowed to be touched or covered.

Power Switch

Press the |/ O Power Switch on the rear of the heater to connect/disconnect power supply.

Onboard Controls

Power Button

Short press to turn on the machine, continuously short press the gear to cycle through three gears: natural air, warm air, and hot air.
Long press for 3 seconds to turn off the machine.

Touch the timer button once, and the digital tube will display 01. Each time the timer button is touched, the timer setting will increase by 1 hour, with a maximum setting of 12 hours. If the timer is cancelled, the corresponding timer display light will turn off.

This heater provides up to 70°heat sweep.Press the Oscillation Button to tun on/off oscillation.

Long press and hold for 3 seconds to activate the child lock function, but all buttons are ineffective.

Press and hold this button again for 3 seconds to contact the child lock status, and the digital tube light will turn off.

The machine is running in the hot air mode, every time it is touched, the set temperature increases by 1° and the digital tube displays the current set temperature. After 5 seconds of no operation, it switches back to the default display.

The machine is running in the hot air mode, the set temperature decreases by 1° C every time it is touched, and the digital tube displays the current set temperature. After 5 seconds of no operation, it switches back to the default display.

Note:

1. The temperature setting range is 59 °F -99 °F.
2. If the ambient temperature exceeds 0 °F -99 °F, it is displayed as -, not a fault, and the machine can operate normally.
3. The machine has an intelligent energy-saving mode. When the machine detects that the ambient temperature is → the set temperature during operation, the machine will automatically stop heating. When the ambient temperature drops to < the set temperature by 3 °F, the machine will automatically resume heating function. When the machine’s warm air and hot air gears are turned on, the default setting is 86° F. You can manually adjust the energy-saving mode setting temperature you need.

Screen Display

Cool Air Mode
When this mode is on, the LED above the ” LO” will be solid white.

Low Heat Mode
When this mode is on, the LED above the ” H1″ will be solid white.

High Heat Mode
When this mode is on, the LED above the ” H2″ will be solid white.

Timer LEDs (1H-12H)
When a timer is on, the Timer LEDs will be solid white to show the remaining hours. (See chart on page 4 for details.)

NOTE: Default display of digital tube: When the machine is working, the digital tube defaults to alternating display of ambient temperature and gear,and the light remains on for 6 seconds to switch.

SAFETY FEATURE

1. A Tip-Over Switch is built in to prevent operation if the Heater is tipped over.
2. A thermal overload protector is built in to prevent overheating.
3. If an overheat temperature is reached, the Heater will automatically shut off. When it cools down after several minutes, you can hit the power button to turn it on.

TROUBLESHOOTING TIPS

If your Heater shuts off unexpectedly or fails to operate, the previously mentioned safety feature may have been activated to prevent overheating.

1. Be sure the power cord is plugged into a working electrical outlet.
2. If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning. See Maintenance section below.
   SERVICING: For servicing, other than general user maintenance, please contact Customer Service at Calefactive@outlook.com
   STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place
   DISPOSITION: Corrugated packaging materials are recyclable. For environmentally responsible disposal of this product, contact your local waste service provider or visit www.Calefactive.com

MAINTENANCE

WARNING

To reduce the risk of electrical shock and fire please observe the following instructions.
Cleaning the Heater regularly will help to maintain its efficiency.
Always unplug the cord before moving, servicing or cleaning.

• NEVER place the Heater in or near water. DO NOT IMMERSE HEATER IN WATER.
• Clean the Heater only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from the surface of the Heater.
  Vacuum the filter cover every two weeks; this will help to maintain the optimum Heater performance.
  Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.
  NEVER attempt to take apart the Heater.
  Clean the body of the Heater with a soft cloth only.
  NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.

WARRANTY (VALID IN THE USA, ITS TERRITORIES, AND CANADA ONLY)

WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.

HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for two (2) years from the date of original purchase or purchase ip mere utena lasts or two 2) years from the date of original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
WHAT WE WILL DO: We will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model.

WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation,shipping damage, abuse, misuse, unauthorized repairs made or attempted, or the use of the product for commercial or nonresidential service. This warranty does not cover shipping costs for the return of products to Pokitter for repair or replacement. Pokitter will pay return shipping charges from Pokitter following warranty repairs or replacement.

ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST THREE YEARS FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL POKITTER’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (I1) REPLACEMENT OR REPAIR OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES.

NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL POKITTER’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.

CUSTOMER SERVICE:
Plas oe you mont to ali, do as a ho ye and ta o and on heroes an and of you produce)
COMP MENS NO MOST HEATER COM ONE MES ARE NOTE RA ETO MAY MERE ANAGE AUNO AERIA CEMENS, MANY ELECTRONIC
Manual printed in China

SPECIFICATIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>