GVM-G175 Alloy 5 Section Monopod User Guide
- June 17, 2024
- GVM
Table of Contents
G175 Alloy 5 Section Monopod
PRODUCT INTRODUCTION
GVM-G175 is a new-released Monopod with Fluid Video Head specially designed
for videographers and filmmakers by GVM.
The 5-section design can meet users’ different demands for height from 645mm /
25.4″ to 1870mm / 73.6″ under various shooting environments. Payload 10 kg /
22Ibs and fast release plate provide compatibility and convenience for fast
mounting and dismounting most cameras and camcorders on the market. The
press-type button on the monopod makes converting vertical and tilted
convenient.
The damping force can be adjusted by rotating the damping and ball locking
knob for a better shooting experience. The included quick-release plate with
1/4″ and 3/8” screws makes camera changes and transport easy.
PRODUCT PARAMETER
- Model: G175
- Weight: 1.8 kg / 4 lbs
- Leg Sections: 5
- Top Attachment: 1/4″ screw, 3/8″ screw
- Maximum Tube Diameter: 32.5mm / 1.28″
- Min Tube Diameter: 18.5mm / 0.73″
- Min Height: 645mm / 25.4″
- Maximum Height: 1870 mm / 73.6″
- Payload Weight: 10 kg / 22Ibs
- Bubble Spirit Level: (No.)1
- Upper Disc Diameter: 60 mm / 2.36″
- Front Tilt: +90°/-75°
- Head Type: Video/Fluid Head
- Leg Type: Single
- Leg Lock Type: Flip Lock
- Material: Aluminum
- Maximum Working Temperature: 60°C / 140°F
- Minimum Working Temperature: -30°C / -22°F
- Pan Bar Included: Yes
- Panoramic Rotation 360°
PRODUCT STRUCTURE ANALYSIS
INSTALLATION METHOD
First insert 1 rocker arm into 2, then pass 3 through 4, insert 5 and pass through the groove of the rocker handle, install it on the left or right of the head according to individual needs, adjust to the appropriate angle and tighten 6, you can lock the rocker handle on the gimbal.
FUNCTION INTRODUCTION & INSTRUCTION
-
QR Plate
An included quick release plate makes camera changes and transport easy. Each QR plate comessite both a 1/4″ & 3/8″ screw for your convenience. The unused screw is stored on the unused screw isstored on the underside of the head. -
QR Plate Mounting and Safety Release
Loosen Quick Release Plate Lock Lever and press the QR Safety Button to allow of Camera using the Mounting Screw then slide back on to Head. Slideand position for best balance and tighten QR Plate Lock Lever. -
Tilt adjustment&Pan adjustment
A side mounted knob adjusts the tension of the drag on front-rear. Tile movements. Rotate to adjust with a camera mounted to find the most appropriate setting.
A pan Drag / Lock Lever provides both Drag and Locking control of horizontal head movement. -
Leg Section Adjustment
Through open or lock the buckle to adjust the height forthis video monopod. -
Support foot vertical and tilt adjustment
The monopod can be vertical and tilted by pressing the button.When the monopod is vertical, you can press the buttonto make it tilted for shooting conveniently. If you want to makethe monopod vertical, press the button again. -
Support foot damping adjustment
When the monopod is vertical or tilted, the damping force canbe adjusted by rotating the damping and ball locking knob for abetter shooting feel. -
Support foot angle adjustment
The support foot has two gear positions, which can be adjusted by pressing the button in order to adjust the supporting angles.
It is convenient for different scenes shooting.
USER NOTICE
Thank you for choosing GVM. Please read this general instruction sheet before using, to avoid any accidental damage.
| Do not exceed the load capacity of this products, (see the specifications).
---|---
| Always ensure the locks and devices are in safety condition to avoid
accidental damage of the camera and other equipement.
| Do not use the product at tempreture less than -20°C or more than +70°C. It
is not recommended to use in seawater.
| Avoid leaving the product in high tempreture, e.g in thesun for long time or
in a car near the car window for hours.
| Ensure keeping the product out of reach of children when working at the
public place in case any accidental hurt. Use it carefully in dangerous place.
| Do not scrub the spirit-level, the precision could be lost temporarily.
| Remove the equipment from the products during transportation.
| It is not necessary to do regular lubrication , but if required, the
standard lubricant oils and grease is ok for the equipment.
| After using in the wet, dusty, sandy, windy days, it isrecommentded to clean
and dry the tripod with soft cloth. The dirt, dust, and sand in all leg locks,
threads, should be removed after use. Clean with mild detergent or alcohol.
| For your own safty, don’t let this products near any electrical power
source and chemical substances.
DISCLAIMERS
- Before using this product, please read the instructions carefully and make sure use the product correctly. If you don’t obey the instructions and warnings. you maybe cause harm to yourself and the people around, or even damage the product and other things around.
- Once you use the product, it means you have already read the disclaimer and the warnings carefully, understanding and agreeing with all the items, and promise to take responsibility of any consequences of using the product.
PACKING LIST
| Name | Quantity | Notes |
|---|
GVM Alluminum
Alloy 5-Section Monopod w/ FluidVideo Head| 1|
Pan Bar| 1|
Hexagon Wrench| |
Carry Bag| 1|
Instructions| 1|
https://www.facebook.com/GVMLED/
Web: www.gvmled.com