i-team i-mop XL plus Industrial Floor Scrubber Instruction Manual

**i-team i-mop XL plus Industrial Floor Scrubber Instruction Manual

**

Introduction

The i-mop® XL plus is a safe, user-friendly machine. This manual helps you to get started and explains the operation and maintenance procedure. You will be pleasantly surprised by the
fast and effective use of the battery operated i-mop XL plus. The batteries used in the i-mop XL plus are the same as the ones in a variety of battery powered i-team products. The batteries must be fully charged before use. Please see the user manual of the class I battery charger for correct procedure.

This manual is intended for those who work with the i-mop XL plus and / or perform daily maintenance. The manual must be read fully before the first actions. This manual describes the correct method of use, safety measures, maintenance and transport.

The manufacturer continuously improves all their products based on user experience and feedback. Any deviations between the texts and / or images from the manual and you  i-mop XL plus can therefore arise from the difference in model or from possible changes due to continuous development and innovation

Intended use of the product
The i-mop XL plus is a specialized machine for scrubbing floor surfaces. You can use any type of water-based scrubbing detergent.

The fluid tank, brushes and squeegee come in HACCP color coded versions (blue, green, red, yellow and orange). All three items can be easily replaced. This allows you to use different cleaning solutions, — for instance, when you move from the food preparing area to the restaurant. Make sure that the color code for the fluid tank, brush and squeegee ALWAYS match each other

Non-intended use of the product

WARNING
Non-intended use can have consequences for the safety of operators and bystanders and will void the warranty on the product.

• NEVER operate the i-mop® XL plus near flammable dusts, liquids or vapors.

• NEVER operate the i-mop XL plus when flammable or poisonous liquids like gasoline, oil, acids, or other volatile substances are on the floor.

• DO NOT fill the i-mop XL plus with any flammable detergent. ONLY use the water based cleaning solutions.

• DO NOT use water that exceeds 113°F / 45°C. Using water warmer than this temperature will void the tank warranty.

• DO NOT use cleaning solutions with a pH level below 3 or above 11 in order to prevent
  damage to sensitive components.

• DO NOT use the i-mop XL plus outdoors or on uneven surfaces.

• DO NOT operate this i-mop XL plus over electrical floor outlets in order to avoid electrical shock.

• NO RIDERS! Do not carry passengers on top of the i-mop XL plus.

• DO NOT use the i-mop XL plus as stepladder or platform.

• DO NOT store the i-mop XL plus outside in order to avoid damage to electronic components.

• ONLY use manufacturer-supplied parts for maintenance.

• KEEP AWAY from children! The i-mop XL plus is a professional cleaning machine to be used by trained adults only.

Lifespan
Each i-mop XL plus is guaranteed to operate for at least 2000 hours. The wear on brushes
and squeegee heavily depends on the roughness of the surface. They need to be checked regularly.

CAUTION
To ensure proper and safe operation throughout the life of the i-mop XL plus, the machine must be checked by an authorized i-team partner every 500 hours.

Modifications
It is not permitted to make modifications to the design of the i-mop XL plus without consultation and permission from the manufacturer. This affects the warranty, see section 1.6 of this manual.

Specifications

0.943
Noise level (1m):| 64.9 Db
Theoretical performance:| Up to 1800 m2 per hour
Practical performance:| 1000 – 1300 m2 per hour
Castor wheels:| YES
Power cut off at store position:| YES
Angle power cut off:| YES < 32°
Floating ball for recovery tank:| YES
Hour counter:| YES

Warranty
The i-mop® XL plus should be used as intended and described in this manual. Using
the i-mop XL plus outside will void the warranty on the product

Identification
The serial number can be found on the deck of the i-mop XL Plus.

Description

The compact i-mop® XL plus consists of two main parts:

• The body that contains the motor, cleaning solution tank, recovery tanks, handle with triggers and control panel.
• The scrub deck that contains the brushes and squeegee.

The i-mop XL plus can be folded into a store position; this is recommended for storage.

The i-mop XL plus consists of:

Legend

1. Trigger
2. Control panel
3. Batteries
4. Scrub deck
5. Splash guard
6. Recovery tank
7. Vacuum hose
8. Rotating brushes
9. Squeegee
10. Solution tank
11. i-dose
12. Waste bin

Safety

Safety comes first. Therefore, please take your time to read and understand these safety instructions. Improper use can cause harm or void the manufacturer’s warranty

General safety instructions
Sweep before scrub
Remove objects from the floor that can be propelled by the rotating brushes.

Brush condition
Make sure to check the condition of the brush before use. Change the brush only when the
machine is turned off and in a store position.

Machine orientation
Always keep the body of the i-mop® XL plus in an upright position when inserting cleaning
fluid or batteries.

Antibacterial tanks
Always keep the antibacterial tanks of the i-mop out of direct sunlight. This can cause discoloration.

Strong magnets

CAUTION
Please be aware of the integrated magnets that hold the fluid tanks in place.

WARNING
Operators and maintenance crew wearing pacemakers should keep a minimal distance of 6 in/15 cm.

Batteries
Always use the automatic battery charger provided by the manufacturer.

CAUTION
During normal operation, the 24V batteries cause no safety hazard on their own. Please adhere to the following safety instructions regarding the batteries:

• Do not crush, pierce or damage in any way.
• Do not heat or incinerate.
• Do not short-circuit.
• Do not dismantle.
• Keep dry.
• Only charge between 5 °C~40 °C / 41 °F~104 °F.
• Only use between 5 °C~45 °C / 41 °F~113 °F.

Risks during operation
Dress safely
Do not wear a necktie, scarf, or any loose or dangling clothing or jewelry while operating the imp® XL plus. These can tangle in rotating parts, causing serious injury or death.

Mark the job site
The i-mop XL plus is designed to leave a dry floor without slippery patches, no additional drying is required. When running the i-mop XL plus with the vacuum function OFF please mark the job site with a wet floor marker.

CAUTION
Marking the jobsite with a wet floor marker is not required when using the vacuum function of the i-mop XL plus, unless this is a mandatory work safety requirement by local law. When unsure mark the job site to warn passersby.

Careful when parking
Do not park the i-mop XL plus on ramps or slopes. Always park the i-mop XL plus on a level,
hard surface. Do not park the i-mop XL plus using the drive support ONLY, the device may fall
sideways. The i-mop XL plus should only be parked either with the park support or by lifting the deck into store position

Careful using drive support
Do not park the i-mop XL plus using the drive support, the device may fall sideways

Risks after operation
Remove battery packs
It is best practice to remove the batteries before executing any cleaning or maintenance task,
or before storage.

Machine orientation
Always keep the body of the i-mop XL plus in an upright (store) position when replacing
brushes or squeegee.

Careful when storing
Do not store the i-mop XL plus on ramps or slopes. Always store the i-mop XL plus on a level,
hard surface. Do not store the i-mop XL plus in park position.

Transport and storage

General
CAUTION
Always keep the body of the i-mop® XL plus in an upright position when filling the cleaning solution tank or inserting the batteries

Before storage or transport, drain the machine and remove the batteries after each use.

Store position
CAUTION
Do not put the i-mop XL plus in store position while the drive support and the park support are active. First deactivate the drive support and the park support.

The store position is the upright vertical position for storage and maintenance tasks.

1. Make sure the vacuum hose (Figure 4, pops 2) is pushed back into the machine so it cannot get squeezed.
2. Crouch down and hold the handle (Figure 4, pops 1) with one hand while holding the scrub deck (Figure 4, pops 3) with your other hand.
3. Lift the scrub deck slowly until it stands upright on the front wheels (Figure 4, pops 4). Guide the body towards the scrub deck until it snaps into a resting position.

Transport outside

When outside:

1. Put the i-mop® XL plus in store position, see section 4.2.
2. Carry the i-mop XL plus with one hand while holding the handle (Figure 5, pos 1) with your other hand.

CAUTION
The transport wheels are not designed to roll over dirty surfaces, sand can cause the wheels to block. Lift the i-mop XL plus while moving from one building to another.

Transport in a vehicle
The preferred way to transport your

1. mop® XL plus is in an upright position and safely secured.
2. Make sure both tanks are empty.
3. Put the i-mop XL plus in store position, see section 4.2.
4. Remove the batteries.
5. Lift the i-mop XL plus into the vehicle.
6. Secure the i-mop using a tension belt or another appropriate restraint (Figure 6, pos 1).

TIP
The i-stand wall mount accessory can be installed in the back of a truck. It allows you to secure the i-mop and transport the i-mop in an upright position. Please contact our sales department for more information.

The i-mop XL plus is a compact machine and fits in the trunk of your car. Before loading the i-mop XL plus into your vehicle, make sure both tanks and battery packs are removed.

1. Put the i-mop XL plus in store position, see section 4.2.
2. Remove the batteries and both tanks and pack them separately for transport.
3. Lift the i-mop XL plus into your vehicle. Don’t forget the tanks and batteries.
4. Prevent the i-mop XL plus from moving around during transport by using a tension belt or another appropriate restraint.

CAUTION
The seal of the solution and recovery tank can be damaged during transport in horizontal position. Make sure you remove the tanks before loading the machine into your car. Improper use will void the warranty.

Assembly and installation

The i-mop® XL plus does not require much assembly. Most importantly, you will have to attach the brushes and squeegee.

Unboxing
The i-mop XL plus body is packed in a single box. The battery and charger are delivered in a
separate box and can be ordered separately

1. 1x i-mop XL plus main body
2. 2x batteries (when ordered)
3. 1x battery charger (when ordered)
4. 1x battery charger manual (when ordered)
5. 1x power cord (when ordered)
6. 1x squeegee assembly
7. 2x brushes
8. 1x cleaning solution tank
9. 1x recovery tank
10. 1x this manual
11. 1x waste bin

Assembly
Charging the batteries
Charge the batteries according to the instructions in the battery charger manual. Make sure
the battery packs are charged regularly

Attaching the brushes

To attach the brushes:

1. Put the i-mop® XL plus in store position, see section 4.2.
2. Hold the scrub deck firmly with one hand.
3. Align the left brush (Figure 8, pos 1) with the left motor disk (Figure 8, pos 2). Align the latches and cut-outs in the brush and motor disk.
4. Push the brush on the motor disk.
5. Turn the left brush clockwise until you see the motor disk turning. The brush is now in place.
6. Align the right brush with the right motor disk. Align the latches and cut-outs in the brush and motor disk.
7. Push the brush on the motor disk.
8. Turn the right brush anticlockwise until you see the motor disk turning. The brush is now in place.

Attaching the squeegee

To attach the squeegee:

1. Take the vacuum hose (Figure 9, pos 1).

2. Insert the hose connector (, pos 2) in the squeegee (Figure 9, pos 3).

3. Twist the hose connector 1/4 turn for a firm fit (Figure 9, pos 2).

4. Carefully pull the vacuum hose back into the machine.

5. Hold the scrub deck firmly with one hand.

6. Align the pins on the scrub deck (Figure 9, pos 4) with the holes on the squeegee
   (Figure 9, pos 5).

7. Push the left side of the squeegee in place.

8. Push the right side of the squeegee in place

Installing the recovery tank

1. Put the i-mop® XL plus in store position, see section 4.2.
2. Put the bottom of the recovery tank (Figure 10, pops 1 and pops 3) on the front of the imp XL plus.
3. Push the top of the tank into place until you hear a ‘click’ sound, the magnet (Figure 10, pops 2) will lock the recovery tank into place

Installing the cleaning solution tank

1. Put the i-mop® XL plus in store position, see section 4.2.
2. Put the tank (Figure 11, pos 1) on the i-mop XL plus with the valve first.
3. Press the tank downward on the nipple to open the valve seal.
4. Push the tank forward into place until you hear a ‘click’.

Installing the recycle bin

1. Slide the rear of the recycle bin (Figure 12, pos 1) into the recycle bin slot.

To remove the recycle bin reverse the movement.

Removing and installing the drive support (optional)

1. Place the i-mop® XL Plus in the active position with the front of the main body leaning against a stable wall.
2. If present, remove the batteries.
3. Remove the nuts (Figure 13, pos. 1) from the bolts (Figure 13, pos. 2).
4. Remove the bolts.
5. The bracket can now be removed and replaced. The preassembled blue bracket is 100 mm and the grey bracket is 90 mm. The blue and grey bracket are interchangeable.
6. Replace the bolts and tighten the nuts.

Operation

Before you start
Check the brushes and squeegee for wear and tear, see section 7 for maintenance instructions

Inserting the batteries

CAUTION
Only use i-power® batteries specifically designed for use in i-mop® devices.

The battery clips (Figure 14, pos 1) are color-coded; blue or grey. The clips correspond with
the color-coded battery slots.

1. Push the blue coded battery (Figure 14, pos 2) in the blue battery slot. A click indicates
   that the battery is locked in place.

2. Push the grey coded battery (Figure 14, pos 3) in the grey battery slot. A click indicates
   that the battery is locked in place.

3. During operation, the battery indicators (Figure 14, pos 4) on the control panel show the amount of power left.
   Filling the cleaning solution tank
   

4. Remove the yellow cap (Figure 15, pos. 1).

5. Pour in a maximum of 1 gal / 4 L of water (Figure 15, pos. 2).

6. But back the yellow cap (Figure 15, pos. 1) and make sure it seals tightly.

7. If applicable, remove the old i-dose pod and remove the cap (Figure 16, pos. 1).

8. Place the desired i-dose pod (Figure

9. pos. 2) in the i-dose injector.

10. But back the cap (Figure 16, pos. 1).

11. Close the i-dose top (Figure 16, pos. 4).

12. Press the i-dose injector button (Figure

13. pos. 5) to dispense the contents of the i-dose pod.

14. Turn the indicator ring so that the color corresponding to the i-dose pod is facing towards you (Figure 15, pos. 3).

Operation procedure

Walking to the job site

To move the i-mop® XL plus from one location to another one in a building:

1. Put the i-mop XL plus in store position, see section 4.2.
2. Hold the handle with one hand (Figure 17, pos 1).
3. Walk slowly and pay extra attention if you pull the i-mop XL plus over obstacles.
4. To lift the i-mop XL plus over obstacles, always use two hands.
   • Hold the handle with one hand.
   • Lift the scrub deck with the other hand.

At the job site

1. Crouch down while holding the scrub deck firmly with one hand (Figure 18, pos 2).

2. Push the handle forward with your other hand (Figure 18, pos 1).

3. Bring the scrub deck slowly down to the floor.
   WARNING
   Never push down the scrub deck with your foot.
   

4. Stand behind the i-mop® XL plus. Choose your cleaning mode via the main switch
   (Figure 19, pos 7). This will also turn on the i-mop XL plus.

   • MODE 1: Brush + water/cleaning solution (Figure 19, pos 1).
   • MODE 2: Brush only (Figure 19, pos 2).
   • MODE 3: Brush + vacuum (Figure 19, pos 3).
   • MODE 4: Brush + water/cleaning solution + vacuum (Figure 19, pos 4).

5.  Hold the handle with both hands.

6. Squeeze the trigger on the handle (Figure 19, pos 9).

7. Once the trigger is squeezed the i-mop XL plus will move forward.

8. Walk behind the i-mop XL plus.

9. Steer by gently turning the handle left or right to move the scrub deck (Figure 19, pos 10).

10. Releasing the trigger (Figure 19, pos 9) will immediately stop the i-mop XL plus. The
    vacuum motor will stop after 3 seconds

TIP: Learn to swivel
Operating the i-mop XL plus is very intuitive and like steering a bicycle. The i-mop XL plus is
designed to move forward. To turn, stop walking and use your inside hand (the hand in the
direction you want to go to) to turn the handle. The i-mop XL plus can swivel 360 degrees
making it possible to reverse direction.

WARNING
Do not operate the i-mop® XL plus at more than an arm’s length. Operating below a 45-degree angle can cause water to run into the vacuum engine.

Drive support

WARNING
Do not park the i-mop XL plus on the drive support, the device can fall down sideways.

1. Push the bracket of the park support (Figure 21, pos 1) down to bring the drive support up (Figure 21, pos 2).
2. Lean the main body of the i-mop XL plus against the drive support.
3. Use the i-mop XL plus as normal.
4. To deactivate the drive support push the entire bracket down

Park support (optional)

WARNING
Do not store the i-mop® XL plus in park position. To avoid wear on the brushes, an alarm will sound and lights will start blinking when the i-mop is in park position for over 10 minutes

1. Push the park support up to activate.
2. Let the main body of the i-mop XL plus  rest against the park support.
3. Park the i-mop XL plus for less than 10 minutes.
4. After 10 minutes the device will automatically be disabled. An alarm will sound and lights will start blinking. Lift the deck to stop the alarm and restart the imop.
5. To deactivate the park support push the entire park support down.

ECO mode
The ECO mode will use 40% less cleaning solution

1. Turn on the ECO mode by pushing the ECO button (Figure 23, pos 1).
2. Turn off ECO mode by pushing the ECO mode again.

Turning off the i-mop® XL plus

1. Use the i-mop XL plus main switch (Figure 24, pos 1) and choose MODE 3 Brush + Dry vacuum (Figure 24, pos 2).
2. Operate it about 15-20 feet / 4-6 meter farther to vacuum remaining cleaning solution up.
3. Then set the main switch to the OFF position.

Note that the vacuum motor will continue to run for approximately 3 more seconds.

Emptying tanks
Dispose of water or cleaning solution from both tanks in an appropriate drain. Even though the recovery tank is bigger, empty it each time the cleaning solution tank is filled.

WARNING
Please observe the local provisions regarding solution disposal related to wastewater treatment.

Cleaning and storage

Flushing the system
Be sure to flush the tanks out completely to discard any remaining solution in the lines and valves:

1. Refill the solution tank with 2 to 4 cups / 0.5 to 1 liter of clean water.
2. Use the i-mop® XL plus main switch (Figure 25, pos 1) and choose MODE 4 Brush + Water/Cleaning solution + Dry vacuum (Figure 25, pos 2)

Cleaning the tanks

1. Dispose of water or cleaning solution from both tanks in an appropriate drain.
2. To clean the recovery tank thoroughly:
   • Partially fill the tank with fresh water and hold it horizontally with the holes facing up.
   • Tilt the tank repeatedly, thoroughly rinsing all the dirt and debris out from the tank.
3. To clean the solution tank, follow the same procedure.

TIP: Dry the tanks
Slightly open both tank caps before storage to allow the tanks to dry

Removing battery packs

1. Put the i-mop XL plus in store position, see section 4.2.
2. Hold the i-mop XL plus by the scrub deck to stabilize.
3. While pressing both plastic pins inwards (Figure 26, pos 1), pull each battery pack away (Figure 26, pos 2).
4. When the i-mop XL plus isn’t used regularly, store the charged battery packs in a dry, clean place.
5. Make sure the battery packs are charged monthly.

Checking the brushes and squeegee

1. Check to see if both brushes are clean and intact, see section 7.1 for removal instructions.
   • Clean them under fresh water or replace them if necessary.
   • Replace brushes if the yellow wear indicator is the same height as other bristles.
2.  Check to see if the squeegee is clean and intact, see section 7.2.1 for removal instructions.
   • Clean it with fresh water and wipe it with a clean, damp cloth.
   • Replace the squeegee blades when necessary

Store in an upright position

1. Please ensure that the i-mop® XL plus is stored in a place where nobody can bump into it.
2. Put the i-mop XL plus in store position, see section 4.2.
3. Store the i-mop XL plus close to a wall (Figure 27, pos 1) with the handle pointing facing away from the wall and the brushes towards the wall

Maintenance

CAUTION
Remove the battery before executing any cleaning or maintenance task.

CAUTION
Always keep the body of the i-mop® XL plus in an upright position when replacing the brushes or the squeegee.

Brush replacement

The brushes are attached to the scrub deck with a bayonet fitting.

1. Put the i-mop XL plus in store position, see section 4.2.

2. Hold the scrub deck firmly with one hand.

3. Using your other hand to turn the left brush (Figure 28, pos 1) anticlockwise until you feel resistance or see the motor disk turning as well.

4. Pull the brush towards you, off the motor disk.

5. Turn the right brush clockwise until you feel resistance or see the motor disk turning as
   well.

6. Pull the brush towards you, off the motor disk.

7. Visually inspect the motor disks.

8. Clean the i-mop XL plus scrub deck with a clean, dry cloth before you install the brushes.

Squeegee replacement
The squeegee blades come in pairs and wear out over time. When you notice the floor is no
longer being dried properly, replace the squeegee blades

Detaching the squeegee

1. Put the i-mop® XL plus in store position, see section 4.2.
2. Hold the scrub deck firmly with one hand.
3. Pull on the left side of the squeegee to remove it (Figure 29, pos 1).
4. Pull on the right side of the squeegee to remove it (Figure 29, pos 2).
5. Remove the vacuum hose from the squeegee by twisting the hose.

Flipping/replacing the squeegee blade

1. Unscrew the 8 plastic nuts on the back.

2. Take off the squeegee rear plate.

3. Once the plastic part is removed, you can easily take off the rear rubber blade.

4. Push the 8 screws through the front blade in order to remove the squeegee front plate.

5. Take off the rear rubber blade.

6. Inspect the front and rear rubber blades:

   • The first time: flip the blades so the top of the blade is now facing the floor. Push the front plate screws through the holes.
   • The second time: attach a new set of blades. Push the front plate screws through the holes
     CAUTION
     The special squeegee blades that contain small arrow-like shapes cannot be switched. These need to be replaced every time.

7. Put back the plastic rear plate.

8. Screw the 8 plastic nuts on the back.

Attaching the squeegee

To attach the squeegee:

1. Take the vacuum hose (Figure 30, pos 1).

2. Insert the hose connector (Figure 30, pos 2) in the squeegee (Figure 30, pos 3).

3. Twist the hose connector 1/4 turn for a firm fit (Figure 30, pos 2).

4. Carefully pull the vacuum hose back into the machine.

5. Hold the scrub deck firmly with one hand.

6. Align the pins on the scrub deck (Figure 30, pos 4) with the holes on the squeegee
   (Figure 30, pos 5).

7. Push the left side of the squeegee in place.

8. Push the right side of the squeegee in place.

Replacing the vacuum hose

1. Detach the squeegee as described in 7.2.1.

2. Remove the solution tank. You can see where the vacuum hose is connected at the
   i-mop® XL plus handle.

3. Hold the scrub deck firmly with one hand.

4. Detach the vacuum hose by twisting the connector 1/4 turn anticlockwise.

5. Now you can carefully pull the vacuum hose from the top of the machine.

6. Guide the new vacuum hose via the opening to the hose connector located at the
   i-mop XL plus handle.

7. Connect the top to the hose connector by twisting it clockwise 1/4 turn until they have
   lined up.

8. Reinstall the squeegee.

Recommended additional cleaning
Clean the exterior of the i-mop® XL plus weekly with a non-abrasive, non- solvent cleaner or a
clean, damp cloth. To clean the scrub deck, remove the brushes.

Recommended service time
Service must be done by one of our service partners. The first service is recommended after
200 hours. It is recommended to schedule a full service every 500 hours.

Check the timer on the control panel on a regular basis. Each decimal step on the timer
registers 6 minutes of operation.

Accessories
The i-mop XL plus can be equipped with different brushes and polishing pads. The use of
these accessories is only allowed by experienced and trained operators as some polishing
pads can be abrasive and can cause damage to the floor surface when applied incorrectly. For
more information please contact our sales department, or the partner who provided the
i-mop XL plus.

Troubleshooting

control panel
Eco mode on| Check the ECO mode lighton the control panel
Empty tank| Fill the tank
Tank incorrectly placed| The tank valve must be clicked on the nipple to openthe seal, replace the tank
Filter blocked| Ensure the solution tank has no dirt particles and the filteris clean
Blocked water pipe| Request for service
Poor water recovery| Squeegee opening blocked| Remove the pipe and cleanthe squeegee opening
Tears in squeegee blades| Replace squeegee blades
Filter blocked| Check the yellow filter andclean if necessary
Vacuum hose blocked| Check and remove blockage
Vacuum pump not running| Request for service
Leakage| Tanks incorrectly placed| Check and reattach fluidtanks
Tear in vacuum hose| Replace vacuum hose or request for service
Battery not charging| Battery is at end of life| Replace battery

Decommissioning and disposal

ATTENTION
It is the responsibility of the i-mop® XL plus owner to dispose of the product responsibly.

After decommissioning, the i-mop XL plus still contains valuable resources and needs to be
disposed of according to your local laws and regulations regarding recycling of electrical equipment

Before disposal please:

1. Flush the machine, see section 6.3.1.

2. Remove the batteries for separate disposal, see section 0.
   TIP :
   Alternatively, keep the batteries for use in another piece of i-team equipment.

3. Remove all loose components like brushes, tanks and squeegee.

4. Dispose all items according to your local laws and regulations.

Attachments

CE Certificate

CERTIFICATE of Conformity EC Council Directive 2014/30/EU Electromagnetic Compatibility
TÜV Rhineland
Registration No.: ΑΕ 50408406 0001
Report No.:
50127657 001
Holder:
Future Cleaning Technologies (FCT) B.V Hoppenkuil 27A 5626 DD Netherlands
Product:
Floor Cleaning Machine
-mop!
Identification:
XL XXL
Becalm 80 ва
Tested acc. to:
Refax to that report 1012747 001 for details
This certificate of conformity based on an evaluation of a sample of the above mentioned product. Technical Report and documentation are at the License Holder’s disposal. This is to certify that the tested sample is is conformity with all provisions of Annex I of Council Directive 2014/30/ This certificate does not imply assessment of the production of the product and does not permit the use of a TÜV Rhineland mark of continuity. The holder of the serrate is authorized to this certificates in somnatction with the EC declaration of confinity ensuring to the a
Date 20.06.2018
Certification
Done Zhou
TÜV Rhineland LGA Products GmbH – Tillystraße 290431 Nurnberg
CE The CE martin may unlay be used if at levant and affective EC Octaves are morphed with CE

Specifications

0.943
Noise level (1m):| 64.9 Db
Theoretical performance:| Up to 1800 m2 per hour
Practical performance:| 1000 – 1300 m2 per hour
Castor wheels:| YES
Power cut off at store position:| YES
Angle power cut off:| YES < 32°
Floating ball for recovery tank:| YES
Hour counter:| YES

The i-Story

It’s not just about cleaning machines.
It’s about the well-being of people and the planet

We are stoked about cleaning, thrilled about sustainability and wholeheartedly dedicated to keep on innovating.

We believe effective cleaning is more than Just’ the removal of soil. It means ensuring the
health and safety of people, while making the job easier, simpler, more efficient and even fun.
It means consistent results all over the world, while protecting the world. And it means creating partnerships to grow our global force for better cleaning. After all, it takes a team. The i-team.

Made Blue
By operating i-mops, your partners, clients and users lower the water footprint whilst contributing positively to the availability of water in the world. Every day an i-mop is turned on, Made Blue simultaneously ensures someone else on the planet gets access to clean water. For every liter that the i-mop uses in operations, the i-team and Made Blue mirror clean drinking water in a developing country. The planet is a beautiful place with over 7 billion people. Humans need water to live, breathe, and enjoy their lives. Worldwide 2,7 billion people suffer from a shortage of drinking water. For 780 million people this situation is permanent each year 3,5 million people die because of this. That’s why Made Blue invests in projects in developing countries. We are a proud partner of Made Blue. Made Blue mirrors the water used by i-team to create clean water in developing countries. 1 liter for 1 liter.

MADE BLUE

i-team Professional b.v.
Hoppenkuil 27b, 5626 DD Eindhoven, The Netherlands
Telephone: +31402662400
Email: hello@i-teamglobal.com
Internet: www.i-teamglobal.com

References

• TeamGlobal
• i-team Global cleaning products - inquire, innovate, inspire

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>