Gorilla Gadgets WMT7 Wall Mount Thermometer with Bluetooth Instruction Manual

Gorilla Gadgets WMT7 Wall Mount Thermometer with Bluetooth Instruction Manual

Statement

1. Please read this manual carefully before use.
2. The ambient temperature of this product is to temperature is °
3. Please do not use this product in an environment above , and the optimal or below
4. Please do not place this product too close to a charged object to avoid electric shock.
5. Do not use this product in an environment with relative humidity greater than 85%.
6. Please do not place this product too close to the electromagnetic range (such as radio, mobile phone, etc.).
7. Please do not expose this product to the sun or near the stove, let alone contact with water.
8. Please do not bump or drop the product, and do not use it if it is damaged.
9. Hair on the forehead, sweat, hat or scarf will affect the accuracy of the measurement data.
10. Please make sure that the measurement distance is not larger than 5cm.
11. In order to obtain accurate and stable measurement data, when the room temperature varies greatly This product should be used indoors for 15-20 minutes.
12. When cleaning is required, please gently wipe the surface of the instrument with alcohol.
13. If there is a problem with the product, please contact Gorilla Gadgets and do not attempt to repair it yourself.
14. The product may have different functions due to production batches or upgrades.

Scope of application

The body temperature of the measured object is displayed by measuring the heat radiation from the forehead.

Structural composition

This product consists of infrared temperature sensor signal receiving processor, buttons, PCB board, beep Device and digital display, battery cover, body.

Part Name

Technical Indicators

Relative humidity : 580%
Transportation storage environment| Temperature: 0 °C- 50 °C ( 32 °F-122 `F ) Relative humidity :
93%
power supply| DC 5V ( 3AA batteries ) /18650/U5B
Display unit| Celsius (°      C) Fahrenheit (°       F)
Size| 100•117*150mm
Weight| 215g
Installation| Wall hanging, double-sided adhesive tape, bracket fixed

How to use

Preventive inspection:

1. The thermometer should be calibrated before measurement to check the function of each component and maintain the good performance of the thermometer
2. Keep the power supply sufficient.
3. After the product is packaged. it is allowed to be transported by common transportation, but it should avoid rain, moisture, and mechanical collision of squeeze boxes.

Operating steps

1. Measurement operation
   Anthropometric

   • Press the measurement key to turn on the thermometer. At this time, the full screen is displayed, as shown in Figure 7-1

   • Switch the thermometer to human body temperature mode, and measure the human body as shown in Figure 17-2].

   • Align the thermometer probe in the middle of the forehead and keep it vertical, the distance is about 1- WU , as shown in the figure Start the measurement. When “di” is issued, the measured value is displayed and the measurement is completed. If the body temperature exceeds the temperature alarm point, a short tone “di, di, di” will be issued to remind the alarm.
     

2. Description of measurement results
   
   
   Body pattern:

3. “Lo’ is displayed on the screen, when the temperature is less than

4. temperature < :the horn play sound ‘Normal temperature’.

5. temperature < :The horn rings twice and play sound ‘High temperature’.

6. temperature *.C, :The horn rings three times and play sound ‘Super High. temperature ,

7. “Hi’ is displayed on the screen, when the temperature is more than
   Note: According to the person’s skin color, thickness and body parts, and when the ambient temperature changes greatly, The measured temperature values will vary, which is normal. The more exposed the human body The bit is more affected by the ambient temperature.

Display icon definition

Memory key: Short press to enter into memory mode, long press to enter into count mode.

Set Key: Short press to change unit between °C and °F Long press to switch language.

Measure key: Short press to measure temperature in Object mode. Long press to adjust volume.

Hold Set and measure key to change object mode.

Contraindications, precautions, Warnings

Contraindications

1. There is no standard value for body temperature, please consult your doctor if you have a fever.
2. Patients in coma and terminal stage.

Cautions

1. This product is a medical infrared thermometer that professionally measures the temperature of the human body. According to the difference of human skin, the measured temperature will be different.
2. When the room temperature changes greatly, the medical infrared thermometer should be placed in the room for 20 minutes before use.
3. When the person to be measured comes from a place that is significantly different from the measured ambient temperature, Stay in the environment for more than 5 minutes. and wait for the ambient temperature before measuring.
4. The surrounding environment of the person under test should be stable. 4 big places to test.
5. Do not use the instrument outdoors or in a place with strong sunlight.
6. Do not hold the front end of the thermometer during measurement.
7. The measurement site must not be covered by hair. If you have sweat, wipe it off with a dry towel Measuring later will affect the measurement result.
8. Fever patients’ cold forehead, sweating and other cooling measures will make the measurement results Low, avoid measuring in this case.
9. After replacement of components (such as batteries) and the host computer that has reached the end of the equipment’s life may cause measurement For measurement errors and accuracy, please handle according to local laws and regulations.

Warning

1. Make sure to remove the hair and sweat from the forehead before measuring.
2. The use of this product cannot replace a doctor’s diagnosis.
3. Please contact the distributor if there is a problem with the product, and do not attempt to repair it by yourself.
4. The protective glass outside the LCD frame is very important, it is also the fragile part of the meter. please use it with care.
5. Do not charge non-rechargeable batteries. and do not throw them into fire.
6. Please do not expose this product to the sun, and do not touch the water.

Battery Installation and replacement

Battery installation or replacement

1. Open the battery cover and replace the battery. Pay attention to the correct position of the positive and negative electrodes.
2. Please do not use rechargeable batteries, use disposable batteries, try to use alkaline batteries.
3. When the instrument is not working, the static current is extremely small, but it is recommended to remove the battery when it is not used for a long time. To prevent battery leakage from damaging the product.

Battery replacement:

The instrument uses 5V manganese or alkaline dry batteries (3 AA batteries). Screen display port, indicating that the battery is already in a low-battery state. the battery must be replaced as soon as possible To ensure the accuracy of the measurement.

Precautions

1. When opening the battery cover and replacing the battery, pay attention to the positive and negative poles of the battery. Improper removal immediately may cause damage to the product.
2. When not used for a long time 1 Please remove the battery to prevent damage due to battery leakage thermometer.
3. Do not use when the battery is leaking or moldy.
4. Do not place the battery close to a fire source or throw it into a fire: To prevent the battery from exploding.
5. Do not store the battery in high temperature or humid environment.
6. In order to avoid short circuit, please do not put batteries and metal objects such as coins or keys in the same place. Pockets or other containers that may short the battery.
7. In case-the electrolyte in the battery accidentally gets into your eyes, please immediately rinse with plenty of water. If there is danger of causing blindness and other injuries: go to the nearest hospital for treatment immediately.
8. In case the electrolyte in the battery accidentally gets on your skin or clothes. please use a large amount immediately. Rinse with water, otherwise skin may be damaged.
9. Replacement of components (battery) and the host computer that has reached the end of the equipment life may cause measurement For measurement errors and accuracy, please handle according to local laws and regulations.

Routine maintenance

During the use of the product. please follow the prompts when you find the following conditions.

1. External dirt: Wipe the dirt with a clean soft cloth. or wipe with a cotton swab and medical alcohol.
   Wiping with medical alcohol can also have sterilization. Watch out for water or alcohol.
   Too much to prevent damage to the inside of the product.

2. Internal dirt: The lens of the internal probe is an important device. Do not use fingers or other objects.
   Touch or press the product, otherwise it will affect the preparation of the measured value. When the lens surface is found.
   When dirty, please wipe the lens surface with a cotton swab moistened with absolute alcohol of 95% or higher purity.
   Tips: Do not use 75% sterile alcohol. (There will be residual water marks on the lens.) Do not use other chemical wipes to clean the lens will Cause damage to the lens).

3. Storage: Keep in a dry and dark place out of direct sunlight.

Troubleshooting

1. Check the measurement object. Forehead blowing, dripping. sweating. Measurement cannot be guaranteed when applying cosmetics.

2. 2.Check the operating environment. Impact of environmental changes on measurement screen display Big. If the ambient temperature changes too much or the instrument has just measurec11.0* Measure ultra-high temperature objects directly to measure low-temperature objects, Tost differences will occur and should be in a relatively stable environment Next. get a new test after about 10 minutes
   Use after thermal equilibration.

3. Check the measurement distance

Buttons do not respond| Re install the battery
No display or display abnormality| Re install the battery
No beep| Check if the beep setting is off
Immediately after shutdown| Check the battery level and reinstall the battery

Warranty

Warranty / Warranty Card Product Quality Assurance

1. Within one year from the date of purchase of this product. the company will provide free warranty service, and the user shall bear the relevant Postage.
2. Our company does not provide free warranty service for the following failures caused by personal reasons of users, details as follows:
3. Failure caused by unauthorized disassembly and modification of the product:
4. Internal failure of the fuselage caused by accidentally falling during handling or use:
5. Failure caused by improper use or lack of reasonable maintenance:
6. Failure caused by not operating according to the correct knowledge in the instruction manual;
7. Failures caused by natural disasters, such as flooding, fire, etc .:
8. Malfunctions caused by improper repairs at repair shops not authorized by the company.
9. Free on request You must present a valid warranty card and proof of purchase when servicing..
10. When requesting warranty service, please bring this product to the point of sale for repair.
11. Repair services outside the warranty will be charged according to regulations.
12. Duration of use: 5 years.
13. When the machine and battery are scrapped, please follow the relevant local regulations.

Warranty Card

Product number:____ machine.  Body number:
Date of purchase: purchase.  Buy a store:____
Customer Name:____ Link Phone:
Customer address:
Dealer’s stamp:__
Maintenance records:____

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>