Bywulanda BH600 Wireless Headset Noise Cancelling Microphone User Manual

Bywulanda BH600 Wireless Headset Noise Cancelling Microphone

Product Overview

Basic Operation

(When powered on, it will automatically reconnect to the last paired device if there is pairing record.)
Power Off| In ‘ON’ status, Long press for 5 seconds to power off
Enter Into Pairing Mode| Power on for 2 seconds (direct earphone alternately flashes red/blue, and the headphone indicator lights up a blue light 30 seconds after pairing successfully
Play/Pause| Short press when play music
Redial a Call| Long press for 2 seconds
Reconnect| Power on to automatically reconnect when there is pairing record.
Voice Dialing| Double press
Audio Switch| Short press 3 times to switch between phone and headset during a calling.
Answer a Call| Short press
Hang up a Call| Short press
Reject a Call| Long press for 2 seconds
Volume +| Volume Up| Short press
Next Song| Long press for 2 seconds
Volume –| Volume Down| Short press
Previous Song| Long press for 2 seconds
MIC Mute Off| Mute Off| The lever Angle is greater than 60 degrees
MIC Mute On| Mute On| The Angle of the lever is less than 60 degrees

Bluetooth Pairing and Connection

A. In ‘OFF’ status, long press 3 seconds to enter pairing mode with Blue & Red indicator light flashing alternately.
B. Search and click to connect ‘BH369A’on your phone Bluetooth list, and blue indicator flashes after successfully connected. That means that you can play music from the headset at this time.
C. Press MFB/ volume+/ volume on the Bluetooth headset to control the answer/hang up a call and play/pause of the music, next/ previous song, volume up/down.

Dongle Connection

Note: If the headset without dongle, please ignore this connection method

A. In ‘OFF’ status, long press 3 seconds to enter pairing mode with Blue & Red indicator light flashing alternately.
B. For the first time, after plugging in and powering on (pairing directly with Bluetooth headset), the red/blue light will cross latent flash when pairing, and the blue light will keep on after pairing successfully. If pairing fails, continue pairing. (When pairing, the red and blue lights flash alternately; Matching success blue light long on)
C. Second use, Headset startup – Connect back to transmitter (blue light flashes 10 times within 24 seconds) failed to connect back (red/blue light flashes alternately) Enter red/blue pairing mode — pairing (600 seconds)– Failed to connect after powering off headset, connect back to transmitter pairing mode

LED Indicator

Charging

Please charge the BH369A at once when the Red LED flashes. Charging time takes about 2 hours. There will be solid and continuous LED Blue when full charged.

1. Charging with Charger

2. Charge with a charging stand

Notes:

1. Pls charge the BH369A at least one time every 3 months when not in use.
2. Charging when the item powered on, the headset will be automatically reset and powered off.

Product Specification

Notes: “Actual use time will differ from environment and music

After-service Email: Bywulanda@outlook.com

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>