Schneider S51-DG Smart Door Lock Instruction Manual

Schneider S51-DG Smart Door Lock

Important Information

Safety instruction

• Read and understand all instructions before using this smart lock. Damages caused by failure to follow instructions is not covered by the warranty.
• It is recommended to use the enclosures/accessories specified by the company.
• Use only alkaline batteries configured with this product.
• Do not forcibly disassemble this product to avoid alarm sound or damage to the product.
• Do not scratch the fingerprint reader with sharp objects, otherwise, ii may cause permanent long-term damage.
• Do not expose the product to corrosive substances, so as not to damage the outer protective layer.
• Do not hang objects on the handle, so as not to affect the normal use of the door lock.
• Cleaning the product, please wipe ii with a soft cloth.
• Do not disassemble the battery while the device is operating.
• Please choose a professional engineer to install the door lock and follow the company’s standard installation instructions, and do not install ii by yourself.
• After the door lock is installed, please modify the default master PIN code immediately and keep the mechanical key in a safe place. Don’t disclose PIN code to the unknown person.
• When low battery alarm is triggered, please replace all the batteries in time

Warning

• Do not place the battery close to the fire in case of explosion.
• Do not short-circuit the two poles of the battery lead with metal objects to avoid explosion.
• Do not let ii happened connection of two terminals of battery lead shorted with metal objects in case of an explosion.
• Make sure replacement or maintenance are done by a professional person authorized by Schneider.
• Your warranty may be invalidated if you used accessories produced by another manufacturer or not recommended by Schneider.

Disposal of used battery and lock

• Please understand the local electronic product classification and collection system.
• Please follow the local regulations and do not discard used batteries into ordinary household garbage.
• Properly disposing of used products helps to avoid potential negative impacts on the environment and human health.
• The battery can not be disposed of with ordinary household garbage

Install your smart lock

Package list
This Package list is for reference only, and all contents are subject to the actual packaging contents.

Explosive view

1. Battery cover
2. M6 mounting screws (3)
3. Back panel assembly
4. Spring (2)
5. Mounting plate
6. Square shaft (2)
7. mortise
8. M6 connecting screw bolt
9. Front panel assembly
10. Bottom cover
11. Screws (4)

Before installation
Check the door open direction before installation

Change cylinder direction

Remark: change the directional screw per door opening way (the screw must be installed on the inner side of the door).

Change handle direction
Change the handle direction of the front panel.

• Unscrewing and taking out the screws. positional component and shieldsleeve in order, then move the cable to the middle hole.
• Rotate handle 180° to the other side.
• Put the cable on the right side, then put the positional component and shield sleeve back and tighten the screws in order properly.

Change the handle of the back panel direction

• Take out positional components.
• Rotate handle 180° to the other side.
• Tighten the screws.

Installation steps

• Note: The mortise connecting cable needs to pass through the hole position shown in the above picture into the door.
  Drill bores following the installation template and then put the mortise into the door and lighten the four mounting screws.

• Note: According to the thickness of the door, select the appropriate length square shaft and connecting screw.
  Install the connecting screw bolt on the front panel, and put the pressure spring and square shaft in the hole.

• Pass the connecting cables and screw bolts through the bore on the door, and then insert the square shaft into the mortise hole of the front panel.

• Install mounting plate to tighten front panel.

• Insert the pressure spring and the square shaft into the hole of the back panel. Then insert the front panel cable and mortise cable into the corresponding interfaces on the back panel. The excess cable plugs back the cable holes and then tighten the screws to fix the back panel.
• Install the battery(4 AA batteries)in the battery compartment and cover it with a battery cover. Check if the front and back panels and other components are connected properly.

Overview

Note: This illustration is for reference, please be subject to the actual product.

Set up your smart door lock

Before you set up
The system mode of the smart lock is divided into security mode and common mode, and the default system mode is common.

User Number
Under security mode, when you enrol in PIN code, fingerprint and card**, you should enter the user number. You can fill in the user information in this table for easy management :

Only applicable in series with key card function.

Enter administrator mode

Before changing the default administrator PIN code(default is 12345678 ), all other settings menu will be disabled. You have to change the administrator PIN code first, then do other lock settings.
For the first time, you need to choose the language, 1 is Chinese, 2 in English;

1. Touch the keypad area to light up the keypad.
2. Press• twice and enter the administrator PIN code with the # key to confirm.
3. Voice prompt: administrator mode.

Modify the administrator PIN code
Under administrator mode:

• Press 1 for a user setting, then press 9 to modify the administrator PIN code.

• Enter the new administrator PIN code and press the # key to confirm, then repeat the above operation. Voice prompt: settings succeeded.

Enroll user PIN code
Under administrator mode:

• Press 1 for a user setting, then press 1 to enroll the user PIN code. Enter 2 digital user numbers and press# to confirm.

• Enter 6-12 digitals user PIN code and press the #key to confirm, then repeat the above operation. Voice prompt: setting succeeded.

• 00-04 is a normal user; 05-08 is a temporary user, which will be invalid after one-time use or under security mode; 09 is a duress user, which works with wireless modules when a duress event occurs.

Enrol User fingerprint
Under administrator mode:

• Press 1 for the user setting, then press 2 to enroll the user fingerprint. Enter 2 digital user numbers and press the # key to confirm.

• Place your finger on the fingerprint sensor and then take away your finger after the voice prompt ” remove your finger and scan again “. Repeat the above steps until the voice prompts “setting succeeded”.

• 00-99 is a normal user, and 95-99 is a duress user who works with a wireless module and triggers the alarm when a duress event occurs.

Enroll user card**
Under administrator mode

• Press 1 for the user setting, then press 3 to enroll the card. Enter 2 digital user numbers with# to confirm.

• Put the card close to the card sensor area until one beep sounds Voice prompt: Settings succeeded.

Delete user PIN code
Under administrator mode:

• Press 1 for the user setting, then press 4 to delete the user PIN code. Press 1 to delete the single-user PIN code and enter 2 digital user numbers with # to confirm. Voice prompt: deletion succeeded.

• Press 1 for the user setting, then press 4 to delete the user PIN code. Press 2 to delete all user PIN codes. Voice prompt: deletion succeeded.

Delete user fingerprint Under administrator mode:

• Press 1 for the user setting, then press 5 to delete the user’s fingerprint. Press 1 to delete a single user fingerprint and then enter 2 digital user numbers with # to confirm or place your finger on the fingerprint sensor until one beep sounds. Voice prompt: deletion succeeded.

• Press 1 for the user setting, then press 5 to delete the user’s fingerprint. Then press 2 to delete all user fingerprints. Voice prompt : deletion succeeded.

Delete user card ** Under administrator mode:

• Press 1 for the user setting, then press 6 to delete the user card. Press 1 to delete a single user fingerprint and then enter 2 digital user numbers with # to confirm or put card deleting close to the card sensor until one beep sounds. Voice prompt : deletion succeeded.

• Press 1 to enter the user settings, then press 6 to enter the user card, and then press 2 to enter all the deletions, the voice prompt is deleted successfully.

Opening mode setting
Under Administrator mode:

• Press 1 for a user setting, then press 7 to set opening mode. Press 1 for a common mode which means it can be unlocked by a single verification PIN code or fingerprint).

• Press 1 for a user setting, then press 7 to set opening mode. Press 2 for security mode which means it is unlocked by dual verification ( PIN code and fingerprint).

System settings
Voice settings
Under Administrator mode:

• Press 2 for system settings, then press 1 to set voice: Press 1 to enter voice mode where all voice is enabled; Press 2 to enter mute mode where voice is disabled except alarm sound and voice guide under master mode.

language settings
Under Administrator mode:

• Press 2 for the language setting then press 2 to enter the system setting: press 1 for Chinese voice; press 2 for English voice.

Record query
System query
Under Administrator mode:

• Press 3 to query record then press 1 to enter system query. The voice reads the serial number.

Extended function (optional)
Join the network Under Administrator mode:

• Press 4 to enter the extended function: press 1 to join the network; press 2 to exit the network.

Use your smart lock

How to open the door from outside

• Touch the pad screen to lighten keypad; then enter the enrolled PIN code. After the voice prompt “Verification succeeded, welcome home”, pressing down the handle to open the door.

• Place the enrolled finger properly on the fingerprint sensor area. After the voice prompt”Verification succeeded, welcome home”, pressing down the handle to open the door.

• Place the enrolled card properly on the card icon area. After the voice prompt “Verification succeeded, welcome home”, pressing down the handle to open the door.

• Under security mode, PIN code + fingerprint (PIN code + card or card + fingerprint) is required to unlock by dual verification.

Unlock with Mechanical Key

If an emergency occurs such as a password loss, running out of battery, or system not working, you can use the spare mechanical key to unlock it.

1. Open the box, take out the key holder and push the button to release the key.
2. Insert the key to the keyhole, make sure the key holder is perpendicular to the key, and rotate the key holder towards the door holder until it is next to the door;
3. Turn the key holder 180 degrees downwards and in the horizontal position, rotate the key holder towards the door holder and open the door.

Lock from Outdoor/ Lock from Indoor/Double-lock from indoor

Anti-Lockpicking from peephole
Anti-lockpicking by fastening the door handle from the inside.

Operation

1. Switch button to red position and turn on peephole security function.
2. Switch button to green position and turn off peephole security function.

Emergency power supply
When the battery voltage is too low to open the lock from outside, you can use 5V power bank to charge the door lock via Micro USB port. After the door is unlocked, please replace all batteries immediately. When the lock system crash down, you can restart system by pressing the reboot button.

• When battery voltage is lower than 4.8V, voice prompts “Low battery, please replace all batteries” at each unlocking. Please replace all batteries immediately, and do not mix old batteries and new batteries together in replacement.

Other functions

Restore to factory setting

• If you forgot your administrator PIN code, long press the [RES] button for 5 seconds to restore factory setting.
• After voice prompted “Restored to factory setting, please change Administrator PIN code”, that means restore to factory setting succeed, and all user data and settings will be deleted.

Reboot button

• Press the reboot button to restart the lock, when the system is unresponsive. No user data is deleted.

Replace battery

• The smart door lock comes with 4 1.5V AA Alkaline batteries.
• It can support 3000 times door openings. ( battery service life may be varied due to use habbit, working environment and working function).

Extended function(optionall)
Extended network module is reserved for smart home system, please contact Schneider for more details.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>