DoubleSight DS-224STB Dual Monitor Free Standing Installation Guide
- June 17, 2024
- DoubleSight
Table of Contents
Model: DS-224STB
Dual Monitor Flex Stand
Quick Installation Guide
DS-224STB Dual Monitor Free Standing
Please Review the entire Quick Installation Guide prior to installation.
If you have any questions regarding the compatibility of this Mount with your
Monitor please contact DoubleSight Customer Service prior to beginning the
installation. It may also be helpful to check your Monitor’s Manual for any
special mounting requirements outlined by the Monitor manufacturer.
Getting Started
Model: DS-224STB
Dual Monitor Flex Stand
Model: DS-224STB
Instruction Manual
Images may differ from actual product.
Disclaimer
DoubleSight intended to make this manual completely all right. However,
DoubleSight makes no claim that the information comprised herein covers all
conditions or details in connection with installation or use of this product.
The information comprised here is subject to change without notice or
obligation of any kind. DoubleSight assumes no responsibility for accuracy or
adequacy of information comprised in this document.
A warning alerts you to the possibilities of personal injury or damage to equipment if you do not follow the corresponding instructions. It is installer’s responsibility to make sure all components are properly assembled and installed using the instructions manual provided.
Using of improper screws size may damage your display. If spacers are required, be sure to use correct size of screws. Proper screws used will easily and completely thread into the display mounting holes. Inadequate thread engagement in the display may cause display falling.
It is installer’s responsibility to make sure the combined weight of all components does not exceed weight capacity. Exceeding weight capacities can result in severe personal injury or damage to equipment. It is installer’s responsibility to make sure the combined weight of all components does not exceed stated weight capacity.
Allowing any part of your component cables to be caught between movable parts can result in serious personal injury or damage to equipment.
The table installed must be strong and stable enough for supporting this monitor mount and monitor (s).
Please contact DoubleSight Displays Service and Support if you are missing any
of the package contents or need assistance.
DoubleSight Customer Support: 888.897.8869 or
Support@DoubleSight.com
Read the following warning before installing
- Verify all parts are included. Do not install if the product if hardware is damaged.
- Please contact a qualified installer
- This product contain moving parts, Use with caution
- This product contains small item, keep these items away from children
- Do not exceed the maximum weight capacity for this product. Exceeding the weight capacity can result in serious personal injury or damage to equipment!
- The table installed must be strong and stable enough for supporting this LCD Arm and LCD.
Specifications
| Weight Capacity | 18 lbs. per monitor |
|---|---|
| LCD Flat Panel Displays | Up to 24″ |
| Pole Height | 15.75″ |
| Base Dimension | 17.75″W x 9″D |
| VESA Bracket Tilt | +/-90 degree |
| VESA Bracket Swivel | +/- 90 degree |
| VESA Bracket Pivot | 180° ± 90° |
| VESA Compatibility | 75mm x 75mm and 100mm x 100mm |
Parts List
ASSEMBLY and INSTALLATION
INSPECT THE MOUNT BEFORE ASSEMBLY
Carefully inspect the mount components to ensure all components are
present.
Note: Read all assembly instructions before staring the installation
process.
Base & Pole Assembly
-
Set Base on flat level surface and screw Pole into position as shown in Figure 1.
-
Adjust Pole Collar to desired Height as shown in Figure 2.
Note: Height can be easily adjusted as needed once monitors are installed.
-
Fasten the Pole into the Base by tightening the screw bolt as shown in Figure 2.5.
Install Monitor Arms
- Install Monitor Arm onto Pole as shown in Figure 3.
- Tighten Arms in place using Bolt as shown in Figure 4.
Install Monitors
- Remove any factory installed stand or base from your monitors.
- Attach and place Vesa Brackets to Monitor Arm with Vesa Knob as shown in Figure 5.
- Install Monitor onto VESA Bracket with Bolt Screws as shown in Figure 6.
- Repeat with second Monitor.
Note: During installation your stand will be unsteady with only one monitor. Care should be taken not to tip the Monitor and Stand.
Adjusting Monitor Height
- Loosen Collar Ring on the Stand Pole and two screws of Monitor Arm and adjust the height of the Monitor Arm.
- Raise Collar Ring to sit firmly under Monitor Arm and fasten both Monitor Arm and Collar Ring into place.
Cable Management
- To organize your Cables, feed cables through the cable opening on each arm as shown in Figure 8.
- Pull cables to center pole and secure in place by snapping them into provided Cable Clips.
CONTACT
DoubleSight Displays
Sales: Tel: 877.896.5237
Email: sales@doublesight.com
Support: Tel: 888.897.8869
Email: support@doublesight.com
Website: www.doublesight.com