TITAN TIPR8812 Galvanized Steel Wood Post Anchor Kit Instruction Manual
- June 17, 2024
- Titan
Table of Contents
TITAN TIPR8812 Galvanized Steel Wood Post Anchor Kit
8×8 Wood Post Anchor Installation Guide
Softwood Installation
IMPORTANT: Do not use on surfaces 30″ or higher (USA) or 600mm (CAN) or higher UNLESS you build according to our Engineering Report’s specs (See QR link below) AND obtain approval by your local authority. Use only Stainless Steel Screws with Aluminum Decking. Sold Separately.
- Step 1
- No knots in the lower 4″-6″ (10-15 cm) of the post. Place the post anchor on the post as illustrated.
- Step 2
- Position the post anchor correctly and use the recommended tools and screw sizes to secure it.
- Step 3
- Drill with a 5/16″ bit and pre-drill at least 4″ deep before installing 3/8″ lag screws. For hardwood posts, use the appropriate larger bit sizes.
- Drill with a 5/16″ bit and pre-drill at least 4″ deep before installing 3/8″ lag screws. For hardwood posts, use the appropriate larger bit sizes.
Specifications
Titan Wood Post Anchor Kit| Recommended Tools| Recommended Accessory| Post
Brace Detail
---|---|---|---
(8) Wood Screw #14 x 2″ T-30 Drive
(4) Lag Screw 1/2″ x 5″
*Concrete screws are sold separately.| Socket 9/16″ (14mm)
3 lbs. Hammer
Ratchet or Drill
T-30 Driver Bit
Hole Saw 1-3/4″ 45 mm dia.
Forstner Bit
Hardwood Installations Only| Use wherever extra strength is desired.| 2×12
2×12
11-1/2″
Concrete Installation
- Step 1
- Drill (1) corner hole & install, (1) screw in anchor. Drill (3) corner holes. *Concrete screws sold separately. 1/4″ x 2-3/4″ min. screw size.
- Step 2
- Remove anchor. Install remaining screws. (With Wood Post)
Engineering Reports for Application Suitability and Attention
- Do not use this product for residential code guard rails UNLESS you have a local engineer or inspector approve your application in your area. Do not use this product as a stand-alone post. It has not been tested for use with vinyl rail systems.
- InterTek engineering reports are for guidance only and complying with them does not necessarily mean your structure will be code compliant. Any variation from the assemblies tested in our engineering reports is outside of the scope of the report.
- This product is not for industrial, commercial or apartment building applications. It is for private residential use only.
Hardwood Installation
IMPORTANT: Use only Stainless Steel Screws with Aluminum Decking. Sold Separately.
- Step 1
- Use a 1-3/4″ Forstner Bit and a 1-1/4″ dia. Hole Saw as depicted to prepare the post.
- Step 2
- Drive the anchor into the post as illustrated to a depth of 4-3/4″ (120 mm).
- Drive the anchor into the post as illustrated to a depth of 4-3/4″ (120 mm).
RECOMMENDED TOOLS
Attention and Disclaime
- This product is not for industrial, commercial or apartment building applications. It is for private residential use only.
- If you wish to use this product for any residential code application including a railing, engage local professionals before beginning work. Always comply with applicable building codes. Building codes may vary.
In no event shall Titan Building Products be liable for any loss or damage, direct or otherwise, which results from the improper use of this product. If for any reason Titan Building Products becomes liable for loss or damage, direct or otherwise the aggregate liability of Titan Building Products shall be limited to the retail purchase price of the products.
FAQ
- Can I use this anchor for surfaces higher than 30″?
- No, unless you build according to the Engineering Report’s specs and have local authority approval.
- What screws should I use with Aluminum Decking?
- Use only Stainless Steel Screws which are sold separately.
- Can this product be used for industrial or commercial applications?
- No, it is designed for private residential use only.
- What should I do before using this product for a railing?
- Engage local professionals and ensure compliance with local building codes.
ATTENTION
- Do not use this product for residential code guard rails UNLESS you have a local engineer or inspector approve your application in your area. Do not use this product as a stand alone post. It has not been tested for use with vinyl rail systems.
- Intertek engineering reports are for guidance only and complying with them does not necessarily mean your structure will be code compliant. Any variation from the assemblies tested in our engineering reports is outside of the scope of the report.
- This product is not for industrial, commercial or apartment building applications. It is for private residential use only.
ENGINEERING REPORTS FOR APPLICATION SUITABILITY
ATTENTION
- This product is not for industrial, commercial or apartment building applications. It is for private residential use only. If you wish to use this product for any residential code application including a railing, engage local professionals before beginning work: (i) to ensure that this product is appropriate for your intended use and that the structural components which this product is to be used in conjunction with are sound and that the work area is safe and free from all potential hazards including utilities and other services, (ii) to provide clarification if these warnings are unclear or you do not understand any of the information in the installation instructions for this product. Always comply with applicable building codes. Be aware that building codes may vary.
- In no event shall Titan Building Products be liable for any loss or damage, direct or otherwise, which results from the improper use of this product. If for any reason Titan Building Products becomes liable for loss or damage, direct or otherwise the aggregate liability of Titan Building Products shall be limited to the retail purchase price of the products.
т 1-866-577-8868