Tuliyet B0CJY31QYD Exclusive 3 Channels Camera User Manual
- June 17, 2024
- Tuliyet
Table of Contents
Tuliyet B0CJY31QYD Exclusive 3 Channels Camera
Please download WIFI products (No download required for non-WIFI)
Press and hold the key to open the hot spot of the machine
Working Environment
- Key Features (picture for reference only, mainly in kind)
PARTS
- Menu / Camera / Playback
- Power button
- Down
- Confirm button
- Up
- Front Camera
- Microphone
- Reset button
- Holder interface
- Rear camera interface
- Power interface
- TF Card slot
- Display screen
- Inside camera(optional)
- Turn night vision on / off
Product Specification
Features
[ ] Power button, short press to turn on/off screen, long press to switch
on/off the device.
[M] Menu/camera/playback button Press the [OK] key to stop recording,
press [M] to enter photo mode, and press [OK) to take a photo; In the
camera mode, press [M] to enter playback mode, press [OK] key to
playback. Lock function: In the case of video recording, short press [M]
for a key lock function to protect the current video file and this file will
not be covered by the cycle video In video mode Lona press Ma to enter the
video menu setting as follows:
In photo mode, long press [M] to enter photo menu settings as follows
:
[ ] Down key, short press [ ] to select function at the Menu interface, short
press button to turn on off sound record at the shooting interface. [ ]Up key.
1, short press [ ]to select a function at the Menu interface; 2, In case of
video recording, short press the OK button to pause, then short press the [ ]
button to switch front- inside view image (require inside view lens); 3, long
press [ ] button to switch front-rear view image; 4, In case of front-rear
view image, short press OK button to pause, then short press (button to switch
front-rear view image (require rear view lens) [OK] Confirm button, short
press to confirm in the menu interface, short press to video record on or off
in the video mode.
Rearview lens (optional)
In the case of video recording, 4 pin plug of the rear view lens is inserted
AV-in hole of the device, there’s a rear view image in the top-right of the
screen, which means it connected successfully; short press the OK button to
pause, long press [ ] button to switch front-rear view image, When hanging up
“R” gear, it will show the full image of the rear view.
Note: This device can only support dual cameras to video record at the
same time instead of 3 3-channel cameras, that is front-inside camera or a
front-rear camera; if installed a rearview.
will not be an overwritten cycle. (note) Gravity sensor (G-Sensor)sensitivity
adjustment support may need to change the setting in the setup menu according
to their image. camera and choose front-inside view mode, it will
automatically indicate the full image of the car reversing visual when you
hang up the “R” gear, but won’t affect the front-inside video record, also
will automatically switch back to front-inside view after cancelling “R” gear.
As for the system update to support 3 channels of camera to video record at
the same time, please prevail in kind and we’re sorry for no further notice.
Reset key [RE SET)
If the recorder crashes and accidental operation is not a normal fault, press
[ RESET] to shut down the device, then press [OK] to reboot the
device.
Installation Notes
-
Please test the rearview camera first, if it works well then install it (a package without a rearview lens can be ignored).
-
Turn off the car engine.
-
The TF card inserts the recorder slot.
Note Please use the high-speed TF card (Class 10 above), a capacity of not less than 4GB, TF card has maximum support of 128GB. -
The recorder via a bracket fixed to the front windshield of the car.
-
Insert the car charger into the car cigarette lighter.
Note When wiring, extend the charging line along the edge of the car door frame and carpet under the car laying. -
Install the rear camera at the rear of the vehicle, and pay attention to the up and down direction. Wiring can be buried along the edge of the car roof laying. [Note There are two ways to install the rear camera:
A . Adsorbed on the glass above and behind the car, hands-on self- installation
(Reversing visual function can not be achieved, only real-time recording rear video).
B . To find a professional installation staff to install the license plate above the camera at the same time need to connect the power reversing lights (Reversing visual function can be achieved). -
Adjust the lens position to ensure the best viewing angle.
-
Start the engine and check that the machine is operating properly.
FEATURES
-
Use the automatic recording function Start the car engine, the recorder automatically starts to open the recording function. Close the car engine, The recorder automatically saves the contents of the log and shuts down, recorded video segments are stored on the TF card. When the TF card is full, the recorder will overwrite the oldest recorded image preferentially.
Note- The time segment of the record can be set to 1/2/3 minutes in the menu.
- The video is individually saved in the folder named “DCIMA” and “DCIMB” in the TF card (package includes rear view lens).
-
Use motion detection In standby mode, enter the menu screen and open the motion detection mode. When the lens is sensitive to the peripheral area of a moving object, the state machine into the camera, recording 30 seconds after the system stops recording. To exit the motion detection mode, in standby mode enter the menu screen and close motion detection mode.
-
G-sensor The built-in gravity sensor (G-sensor), if serious vehicle collision, the recorder will lock the first 5 seconds and 10 seconds after the image date when the accident occurred while the bottom left of the display screen displays a lock icon; locked images will be saved as a special file, the file.
-
The device has a key lock feature that will need to retain an image without being locked loop overwritten. In the video mode, short press [M] key logger will then lock the entire video image.
-
In shooting mode, Press the [M] key to enter the menu setting, find the date/ time menu, short press the [OK] button to confirm and return to the setup menu settings, and press the [M] key to exit the menu setting. note To effectively record the date and time of traffic safety accident forensics, before using the menu setting.
-
File playback In the playback mode, press the [OK] key to play back. To exit playback mode, press the MODE button again.
-
Reversing visual function First, you must connect the DVR to the car charger, and the rear-view camera connects to the reversing lights. Insert the car charger, and the machine will automatically start recording status, screen switch R position in the recording mode automatically switches to the rear-view camera, and display the reverse image. After reversing the visual machine automatically returns to video mode.
Reminder: Please test the rearview camera is normal before installation. -
Parking monitor(To achieve unattended surveillance video) To achieve this function must be connected to the machine in the case of electricity, in the main menu to open the motion detection and parking monitoring function, in the standby state of the vehicle under vibration or moving objects in front, the recorder according to G-sensor to sense automatically start the machine and automatically locks the video for 30 seconds, and automatically save the video file, the video 30 seconds after 5 seconds without the operation will automatically shut down. note This function is only used when stopping. Please turn off the motion detection and stop monitoring function during normal driving.
FAQ
Install the APP and connect to WiFi
- Press OK at the bottom of the recorder to stop recording
- Long press the M key to display the menu
- Tap the M button to change to the menu, select Wifi Control in the menu and turn it on.
- In the cell phone settings page, connect the car recorder’s wifi
- ACTION CAM60def40f5fbO. WiFi Password: 12345678
- After a successful connection, open the APP to use it.