COSTWAY JV11315 Rolling Storage Cabinet Installation Guide
- June 17, 2024
- COSTWAY
Table of Contents
COSTWAY JV11315 Rolling Storage Cabinet
Product Information
| Office Locations | Email Contacts | Model Number | Language |
|---|
USA: Fontana
AUS: Truganina
GBR: Ipswich
FRA: Saint Vigor d’Ymonville| USA: cs.us@costway.com
AUS: cs.au@costway.com
GBR: cs.uk@costway.com
FRA: cs.fr@costway.com| JV11315| EN (English)
Specifications
- Main frame / Cadre principal x1
- Left and right front doors / Porte avant gauche et droite x1
- Fixed shelf / Tablette fixe x2
- 2pcs with brake / 2 avec frein x2
- 2pcs without brake / 2 sans frein x2
- Caster / Roulettes x4
- Anticollision Corner / Coin anticollision x4
- Cable tie / Collier de serrage x1
- L bracket / Crochet en L x1
- Anchor / Ancre x1
- Self-tapping screw / Vis autotaraudeuse x1
- Washer / Rondelles x13
Product Usage Instructions
Assembly
- Install the Fixed shelf (Part) on the frame by lining up the groove to the bottom wire of frame and pressing firmly.
- Repeat Step 1 for the Lower support rod (Part). Please note that the Lower support rod has 2 convex pins, the convex pins should face upward when installing.
- Install Adjustable bucket (Part) into the hanging hole of the Main frame and press it down. Four hanging pieces need to be hung at the same height.
- Install Adjustable shelf (Part). The hole at the bottom of the shelf should be aligned with the hanging piece and inserted.
- Insert the backplane into the U-channel at the back.
- Distinguish the left and right front doors, the top side should have a spring tab pin.
- Insert the Convex pin of Lower support rod (Part) into the hole at the bottom of the Front door (Part), and then press and hold the tab pin at the top of the front door to insert it into the hole of Upper support rod (Part).
- Tear off the adhesive film of Anticollision Corner and stick it on the four corners at the top of the cabinet.
- Description of gap adjustment at the top of the door frame: the casters need to be adjusted according to the actual situation. When the left door is lower, the left casters should be adjusted higher, and so on.
Return / Damage Claim Instructions
If you need to make a return or file a damage claim, please follow these
instructions:
- Contact our friendly customer team at the respective email address for your region:
- USA: cs.us@costway.com
- AUS: cs.au@costway.com
- GBR: cs.uk@costway.com
- FRA: cs.fr@costway.com
- Provide them with your model number (JV11315) and explain your issue.
FAQ (Frequently Asked Questions)
-
Q: How many fixed shelves are included?
A: Two fixed shelves are included. -
Q: How many casters are included?
A: Four casters are included, two with brakes and two without brakes. -
Q: How can I adjust the gap at the top of the door frame?
A: The casters need to be adjusted according to the actual situation. When the left door is lower, the left casters should be adjusted higher, and vice versa.
If you’re having difficulty, our friendly customer team is always here to help
Before You Start
- Please read all instructions carefully.
- Retain instructions for future reference.
- Separate and count all parts and hardware.
- Read through each step carefully and follow the proper order.
- We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
- Always place the product on a flat, steady and stable surface.
- Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.
PARTS
OVERVIEW
INSTALLATION
-
Lay the Mainframe (Part①) on the floor so that you have access to the base of the rack.
-
Take the Caster(Part ⑨) and screw it into the Mainframe feet in a clockwise direction by using the wrench. Be sure to screw it until it is tight.
-
Push the pin on the left and right sides of the Upper support rod(Part ④) into the round hole on the top of the main frame at the same time, and then press down.
-
Repeat Step 3 for the Lower support rod(Part③). Please note that the Lower support rod has 2 convex pins, the convex pin should face upward when installing
-
Install the Fixed shelf (Part ⑤) on the frame by lining up the groove to the bottom wire of the frame and pressing firmly.
-
Install the Adjustable bucket (Part ⑩) into the hanging hole of the Mainframe and press it down. Four hanging pieces need to be hung at the same height
-
Install Adjustable shelf V(Part⑥). The hole at the bottom of the shelf should be aligned with the hanging piece and inserted.
-
Insert the backplane into the U-channel at the back.
-
Install the Top shelf(Part ⑦) on the frame by lining up the groove to the bottom wire of the frame and pressing firmly.
-
Left front door
Screw through the corresponding hole position of the front door and use Philip key to install the handle in front of the front door. -
Distinguish the left and right front doors, the top side should have a spring tab pin
Insert the Convex pin of Lower support rod(Part③) into the hole at the bottom of the Front door(Part②), and then press and hold the tab pin at the top of the front door to insert it into the hole of the Upper support rod(Part④). -
Tear off the adhesive film of the Anticollision Corner and stick it on the four corners at the top of the cabinet.
Description of gap adjustment at the top of the door frame: the casters need to be adjusted according to the actual situation. When the left door is lower, the left casters should be adjusted higher, and so on. -
Use an anchor and screw to install the L bracket into the wall. Then attach the cabinet to L bracket using the cable tie.
Return / Damage Claim Instructions
-
DO NOT discard the box / original packaging.
In case a return is required, the item must be returned in the original box. Without this your return will not be accepted. -
Take a photo of the box markings.
A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts. -
Take a photo of the damaged part (if applicable).
A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged. -
Send us an email with the images requested.
Email us directly from the marketplace where your item was purchased with the attached images and a description of your claim.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE
USA office: Fontana AUS
office: Truganina
GBR office : Ipswich FRA
office: Saint Vigor d’Ymonville
USA : cs.us@costway.com
AUS : cs.au@costway.com
GBR : cs.uk@costway.com
FRA : cs.fr@costway.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>