EHRGEIZ FUSION LED Fusion Bar User Manual

USER MANUAL

Introduction

Thank you for your purchase and usage of the Ehrgeiz Fusion 2.
You have chosen a reliable product with outstanding features. The device is easy to use and is made of high quality components.
Every Ehrgeiz Product is checked before shipping to secure you are able to receive a great product without compromise. This is not a toy. Our ambitious aim is to get you a reliable working tool.

Safety Instructions
In General
In order to maintain the condition and to ensure a safe operation, it is important for all users to follow the safety instructions and warning notes written in this manual.
Do not operate the fixture with missing or damaged covers, shields or any optical component.
Please consider that unauthorized modifications to the device are forbidden due to safety reasons.
If the device is operated in any way that’s not described in this manual, the product may suffer damage and the guarantee will become void. Furthermore, misuse may lead to dangers like short-circuit, burns, electric shock, burns due to ultraviolet radiation, lamp explosion, crash, etc.
IP65 protection rating
The fixture is dust tight (first digit 6) and protected against water jets by a nozzle against enclosure from any direction (second digit 5).
Prevention from electrical shock
Make sure to ground (earth) the fixture electrically. (It’s essential to connect the yellow/green conductor to earth)
Main Connection
Do not apply any AC mains power to the fixture at any other voltage than that specified.
Rigging
Check that all external covers and rigging hardware are securely fastened.
When choosing the installation-location, please make sure that the fixture is not exposed to extreme heat. There should not be any cables lying around. You endanger your own and the safety of others.
Make sure that the area below the installation place is cordoned off when rigging, de-rigging or servicing the fixture.
If suspending from a rigging structure, fasten the fixture to a rigging clamp with M10 bolts screwed into the threaded hole in the center of the brackets of the fixture.
Make sure all fixtures are operated and installed by qualified personnel with the relevant national certifications.
Install, as described in this manual, a secondary attachment such as a safety wire that is approved by an official body.
Positioning:
The fixture must be positioned at least 0.2m minimum distance to illuminate objects.
Keep all inflammable materials at least 0.2m from this fixture.
Allow to place the fixture on an inflammable surface.
The maximum ambient temperature of 40°C may not be exceeded.
The exterior of this fixture can reach a very high temperature during operation. Avoid contact by persons and materials.
Maintenance:
This fixture is for professional use only. It is not for household use.
Always unplug the mains for any maintenance.
Risk of eye injury:
Do not stare directly into the light when it is switched on. Do not look at LEDs with magnifying glasses, telescopes, binoculars, or similar optical instruments that may concentrate the light output.

Delivery Contents
You received your Fusion 2 with the following content 

Fixture Dimensions

Installations

Your Fusion 2 can be installed in every kind of following positions. Please see the explanations and rely to the instructions for a safe operation and secure handling.
Structural Connection
The Fusion 2 can be connected using the included quick-release pins. Place the devices next to each other.

Insert both Pins to connect the devices.

For the first uses this may be a little hard. Move the devices a little until the Bolts can be inserted completely.
For vertical installation do not exceed the amount of 3 pieces. (caution, provisional specification) In case of hanging installation, each device needs to be saved individually!
Using the quick-release pins for horizontal installation is not recommended. Each device should individually be installed with the given installation options below.
Horizontal Installation on the floor
You could place the Fusion 2 on the floor. Please make sure the surface is plane and the reliability of the floor is sufficient.

Horizontal hanging with tilt bracket
You can attach the Fusion 2 to a Truss or Pipe. Notice that the tilt bracket should face down from the hanging structure.
Use the centered holes in the Tilt Bracket

Horizontal hanging with Omega Bracket
You can use the additional fix Omega Brackets (optional accessory) to hang the device horizontal

Safety attachment
In any case of rigging the device attach the Safety rope to any of the dedicated eyelets integrated into the sliding brackets.

Hanging vertically “dropped”
Use the vertical Adapter set (including Omega Bracket, optional accessory) to “drop” the Fusion from a rigging structureNotice that we will release a detailed rigging manual for the different options shortly.
Vertical Installation on the floor
Use the vertical Adapter (optional accessory) in combination with a base plate (optional accessory).
Use the Small standing plate (optional accessory) if you only wish to install one Fusion 2.
If you want to install more than one device, screw the Small standing plate to a normal truss base plate.
Notice that we will release a detailed rigging manual for the different options shortly.

Connections

Mains & DMX
Fusion 2 offers standard powerCON TRUE1 as well as fully IP65 rated 5 pin XLR connectors for the Mains and DMX connection.
Please only use high quality cables fitting the local regulations and connection standards.
We only recommend the usage of H07 RN-F 3G2.5 on Original Neutrik powerCON TRUE1 for mains connection and digital 110 Ohm DMX cable with original Neutrik 5 pin XLR HD.

The internal power wiring is done with a cable cross section of 2.5mm².

DMX
We recommend the use of High quality XLR connectors like original NEUTRIK HD. Please use professional digital DMX cable with a surge impedance of 110 Ω.
Please notice that the USITT DMX Standard does allow to use a max of 32 DMX fixtures in one line. You should terminate the signal by a 120 Ω resistor.
In the Standard mode the Fusion 2 uses 12 DMX channels.
Connect the devices and increase the value of the DMX channel by 12 from one device to another
Wireless DMX
The device can be equipped with a Wireless DMX Receiver from Wireless Solution Made in Sweden (W-DMX ™).
Please contact your Ehrgeiz distributor for detailed information of the necessary hardware & software update.
When the W-DMX receiver is installed, enable it with the option in the service Menu (only needs to be done once and does not set back when you set the device to “factory default”
To establish a connection, enable the W-DMX Option and simply use the “Link” Option in the Fusion 2 Menu. After that, set your transmitter to Link Mode.
After both devices are linked you will be able to control the device via Wireless DMX, as long as the W-DMX Mode is turned on in the Menu.

Operations

Menu control
Your Fusion 2 has an easy to read and setup OLED display and Menu. It is programmed with a lot of built in functions as well as DMX Modes for different applications. Please notice that the display will flip automatically while you turn the fixture (Can be disabled in the menu).

The Menu of the Fusion 2 is mainly intuitive. You will find a menu map on the following pages. The four buttons are used to scroll the values, select a setting or hop back in the menu structure:

Menu map

Advanced -17
Pattern -27
RGBW – 4
compressed – 6
Pixel — 92
Pixel RGBW – 80
Pixel Dim -32| Set the desired DMX Mode.
For detailed information see DMX Modes on page 13.
RDM| On / Off| Enable / disable the RDM function
Reset via DMX| On / Off| Choose whether a device reset can be done via DMX signal
No DMX| Shutter Closed
Hold
Play Programl
Play Program2
Play Program3| Choose the behavior in case of DMX loss
W-dmx| Off
Receive
Transmit| Choose the usage of the W-DMX receiver (optional accessory)
Link
Unlink| Link or unlink the transmitter / receiver;
For detailed information see Wireless DMX on page 7
DMX Live| Refresh rate| xxx Hi| Show the DMX values received.
Color Wheel| 0 — 255
Red| 0 — 255
Green| 0 — 255
Blue| 0 — 255
White| 0 — 255
Shutter| 0 — 255
Dimmer| 0 — 255
CTO| 0 — 255
Pattern| 0 — 255
Pattern Speed| 0 — 255
Pattern Fade| 0 — 255
Control| 0 — 255
Personality| Dimmer Curve| Linear
Theatrical
Square Law
Inverse Square| Choose the Dimmer Curve.
For detailed information see Dimmer Curves Appendix page X
---|---|---|---
Dimmer Speed| Fast
Smooth| Select the behavior of the Dimmer
Display Setting| Shut-off time| Off
1 minute
5 minute
60 minute| Choose after which time the display backlight will turn off.
No signal flash| On
Off| Choose if the Display should blink if there is no DMX signal received.
| Flip Display| Auto
Off
On| Choose if the display should be turned around
Temperature
Unit| Celsius
Fahrenheit| Choose the unit the temperature is displayed
Lock| *Off
On| Enable the Lock Function of the device
Set password| | | I Set a password for the device
Boot mode| Select Mode| Auto
DMX
Static
Program| Select what the device should do when starting up.
Auto means device does the last thing beforecutting power off.
DMX
High Priority| On/ Off| If enabled, the DMX signal always takes priority, no matter which boot up mode is chosen
IR Priority| Off / On| Enable if you want to use the IR remote, even if a DMX signal is received
Stand Alone| Test Sequence| Run / Cancel| Runs a test program with all colours and all single LEDs
---|---|---|---
Master/ Slave| Alone| Choose Master to send out all 3 internal programs to the DMX line if you run any program
Master
Slave| Slave 1|

Choose Slave 1 to replay the first program sent by a Master device. Slave 2 plays Program 2, Slave 3 plays Program 3

Slave 2
Slave 3
Static
Mode| Color Wheel
Red
Green
Blue
White
Shutter
Dimmer
CTO
Pattern
Pattern Speed
Pattern Fade| 0 – 255| Set a static color & Pattern.
Dimmer & Shutter are @255 as standard, all other values @0
Reset All| Yes
No| Set all values in static to default values (Dimmer & Shutter @255, all other values @000
Program Edit| Program 1| Prog1
Steps| Select Step| 01-30| For detailed information see
chapter Program Mode on page 13
Capture DMX| Yes /Cancel
Color Wheel
Red
Green
Blue
White
Shutter
Dimmer
CTO| 0-255
Reset All| No / Yes
Hold Time| 000-99
Fade Time| 000-99
Program 2 / 3| (See above)| For detailed information see chapter Program Mode on page 13
Program Play| Program 1 / 2 / 3
Program All| No / Yes
Program Reset| Program 1 / 2 / 3
Program All| No /Yes
Service| Reset| Fixture Reset| Reset / Cancel| Reset fixture like you do while rebooting
---|---|---|---|---
Calibration| Disabled| Choose if you would like the most power out of the device
Enabled| Choose if you use different Ehrgeiz devices, so all are the same color
Customt| Red| 0-255| Set the maximum level for each
Green| 0-255
Blue| 0-255
White| 0-255
W-DMX installed| No /Yes| Choose whether a W-DMX Receiver / Transciever is installed or not (optional accessory)
Factory Default| Load| No /Yes| Set all settings back to factory default values except the “W-DMX installed” Option
Information| Fixture time| Resettable| xxx Hours| Take a look at the working hours of the device or clear the resettable working hours.
Total| xxx Hours
Clear Resettable| Clear / Cancel
Fixture Temp.| Actual| xxx C/ F| Take a look at the actual and maximum
Temperature or clear the maximum value.
Notice that device does not go back to default display view if temperature is shown.
Max| xxx C/ F
Reset Max| Cancel/Confirm
Firmware version| x.x.x.x| Shows the installed firmware version
Serial Number| xxxxxxxxxx| Shows the Serial Number of this device
Product ID| 200161
Fusion 2| Shows the Product ID

Software updates
Your Fusion 2 can be updated via the DMX connection, so no need to open it.
If you experience an issue which could probably be solved by a Firmware Update, please contact your Ehrgeiz Dealer for further instructions.

IR Control
The IR remote provides these functions:

Increase colour intensity
Colour 0% / Colour 100 %
Decrease colour intensity
Choose a color
Increase speed / intensity
Decrease speed / intensity
Choose an internal program
Choose if program does a chase or fade; Pause program; blackout

Program Mode
You can choose AND Edit the 3 internal Programs.
A description will follow soon…

DMX Modes
You can set up your Fusion 2 in 8 different DMX Modes:
Standard
Page 15; Uses 12 DMX channels
Advanced
Page 15; Uses 17 DMX channels
Pattern
Page 16; Uses 27 DMX channels
RGBW
Page 16; Uses 4 DMX channels
Compressed
Page 17 Uses 6 DMX channels
Pixel
Page 17 Uses 92 DMX channels
Pixel RGBW
Page 18 Uses 80 DMX channels
Pixel Dim
Page 18 Uses 32 DMX channels

Standard

Advanced

Pattern

RGBW

Compressed

Pixel

Pixel RGBW

Pixel Dim

Services

Trouble Shooting

like in the specification
Power Cable defective| Exchange the Power Cable
Display defective| Contact your distributor for repair
Main PCB defective
PSU defective
Fixture does not respond to DMX signal| DMX Cable defective| Exchange the DMX Cable
DMX Cable too long / bad quality| Exchange the DMX Cable to a cable in specification
Wrong DMX Address| Change the DMX Address
Wrong DMX Mode| Change the DMX Mode
Fault on Data Link| Check which device causes the fault
DMX Signal not in Specification| Only use a DMX Controller which sends a Signal which is compatible to DMX512-A like specified in USITT 1990 or DIN 56930-2
W-DMX turned on| Turn off the W-DMX so the device can receive the wired DMX signal
No light output| Device does not receive a DMX signal| See “Fixture does not respond to DMX signal”
Device is too hot| Wait until the light is cooled down
Do not use the light in conditions with an ambient temperature above 40° Celsius
Device is defective| Contact your Ehrgeiz distributor for repair

Maintenance
There are no user-serviceable parts inside your Fusion 2. If problems occur, contact your Ehrgeiz dealer or a qualified Ehrgeiz Service technician.
Use a slightly moist and smooth cloth to clean the device. Do not use any aggressive detergents.
We are sure you will have a sophisticated experience with your Fusion 2.

Appendix

Specifications
Light Source

• 20 x 15W Osram® RGBW LEDs
• LED Life Expectancy: approx. 20.000 hours

Optical System

• ConsistentColor™ Optics
• Beam angle 6°

Functions

• RGBW, 8 bit or 16 bit color mixing
• SteadyColor™ Dimming
• Seamless CTO
• Virtual color wheel with 39 colours including whites (2.700 K, 3.200 K, 4.200 K, 5.600 K, 7.200 K and 8.000 K)
• all 20 LEDs controllable individually
• Pattern effects with variable speed and fade time
• High resolution dimmer 0–100%
• Selectable dimming curves
• Strobe with variable speed (max. 20 Hz)
• Pre-programmed random strobe & pulse effects

Thermal

• Maximum ambient temperature: 40 ° C (113 ° F)
• Convection cooled

Control and programming

• Setup and addressing via OLED display with 4 buttons
• Protocol: USITT DMX-512
• Control channels: 4, 6, 12, 17, 27, 32, 80, 92
• 8 DMX protocol modes
• Stand-alone mode
• Wireless DMX optional
• RDM
• DMX In/Out: XLR 5 pin (IP65)
• Power In/Out: Neutrik powerCON TRUE1

Electrical Specification

• Electronic auto-sensing switching power supply
• Input voltage: 100–240V AC, 50-60 Hz
• Max. power consumption: 330 W

Rigging

• 2 x Hole for M10 bolt
• 2 x Omega Bracket (optional accessory)
• Mount for safety wires
• 2 x stand with manual horizontal tilt
• Vertical Stand foot Adapter (optional accessory)
• Vertical hanging Adapter (optional accessory)
• Vertical Connection via quick-release pin
• Mechanical Specification

IP65 rating

• Height including bracket: 231 mm (9.09″)
• Height without bracket: 181 mm (7.12″)
• Width: 90 mm (3.54″)
• Depth: 1006 mm (39.60″)
• Weight: 12.5 kg (27.55 lbs)

Included accessories

• powerCON TRUE1® / Schuko Input cable
• Glare Shield
• Tilt Brackets with fast locks
• Quick Release Pins

Optional accessories

• Vertical Installation Adapter (hanging or standing) incl. Omega Bracket
• Omega bracket (set of 2)
• Diffusion Filter (20° / 40° / 60° / asymmetric 10×60° / Wall wash filter)

Exploded drawing

Exploded drawing accessory

Spareparts

#| article code| description| amount| | #| article code| description| amount
---|---|---|---|---|---|---|---|---
1| 200187| front plate| 1| | 31| 200335| Display mounting plate| 1
2| 200188| lens plate| 20| | 32| 200206| button mounting plate| 1
3| 200189| lens holder front| 2| | 33| 200204| silicone gasket for display| 1
4| 200191| lens holder back| 2| | 34| 200205| display cover| 1
5| 200190| lens 6°| 20| | 35| 200333| button silicone cover| 1
6| 200192| distance bolt front plate| 8| | 36| 200207| display pcb| 1
7| 200193| distance bolt lens holder| 20| | 37| 200213| mounting plate PSU & W-DMX| 1
8| 200327| IR PCB| 1| | 38| 200208| membrane| 1
9| 200328| distance bolt IR PCB| 2| | 39| 200210| powerCON TRUE1 Power-Out| 1
10| 200216| LED PCB| 10| | 40| 200209| chassis connector 5pin XLR female IP65| 1
11| 200217| housing / heatsink| 1| | 41| 200263| W-DMX Nano Transceiver| 1
12| 200194| sealing for side plate| 2| | 42| 200334| distant bolt W-DMX mount| 2
13| 200195| side plate| 2| | 43| 200264| W-DMX Support Bracket| 1
14| 200196| distance bolt back plate| 4| | 44| 200265| W-DMX bracket for Antenna mounting| 1
15| 200329| bracket for driver PCB mount| 2| | 45| 114200| Antenna Cable| 1
16| 200214| bracket for driver PCB| 10| | 46| 114465| Antenna Cone IP65| 1
17| 200212| driver PCB| 10| | | | |
18| 200215| main PCB| 1| | A1| 200220| Glare Shield| 1
19| 200211| Mounting Plate for Main PCB| 1| | A2| 200260| ball lock pin| 2
20| 200197| cable guide PSU| 4| | A3| 200252| Powercable TRUE1 – Schuko| 1
21| 200198| PSU| 2| | A4| 20336| Standfoot with Tilt Function (Set of 2)| 1
22| 200199| terminal block| 1| | A5| 200161| LED Fusion 2 RGBW 20x15W| 1
23| 200201| back plate| 1| | A6| 200251| Diffusor filter Black Tube| 1
24| 200203| chassis connector 5pin XLR male IP65| 1| | A7| 200271| Vertical Adapter Plate (w/o Omega Bracket)| 1
25| 200202| powerCON TRUE1 Power-In| 1| | A8| 200272| Omega Bracket for Vertical Adapter| 1
26| 200330| plastic cover 1/4 Turn fast lock mount| 4| | A9| 106599| Omega bracket| 2
27| 200331| 1/4 Turn fast lock mount| 4| | A10| 200174| Diffusion filter 40° for Fusion2| 1
28| 200332| sliding bracket mount| 4| | A10| 200175| Diffusion filter 20° for Fusion2| 1
29| 200267| sliding bracket (set of 2)| 2| | A10| 200176| Diffusion filter 60° for Fusion2| 1
30| 200200| mounting plate psu & terminal block| 1| | A10| 200177| Diffusion filter 60×10° asym. for Fusion2| 1

*only for W-DMX Upgrade!

Colourwheel channel chart

(fast – slow)
11 – 15| LEE 157-Pink| | 186 – 190| Coulourwheel rotation stop
16 – 20| LEE 332-Special Rose Pink| | 191 – 205| Coulourwheel rotation backward (fast – slow)
21 – 25| LEE 328-Follies Pink
26 – 30| LEE 345-Fuchsia Pink| | 206 – 210| Coulourwheel rotation stop
31 – 35| LEE 194-Surprise Pink| | Random colours
36 – 40| LEE 181-Congo Blue| | 211 – 225| Fast – slow
41 – 45| LEE 071-Tokyo Blue| | White hue
46 – 50| LEE 120-Deep Blue| | 226 – 230| Tungsten Simulation
51 – 55| LEE 079-Just Blue| | 231 – 235| Warmwhite – 3200K
56 – 60| LEE 132-Medium Blue| | 236 – 240| Neutralwhite – 4200K
61 – 65| LEE 200-Double CT Blue| | 241 – 245| Coldwhite – 5600K
66 – 70| LEE 161-Slate Blue| | 246 – 250| Coldwhite – 7200K
71 – 75| LEE 201-Full CT Blue| | 251 – 255| Coldwhite – 8000K
76 – 80| LEE 202-Half CT Blue| | |
81 – 85| LEE 117-Steel Blue| | |
86 – 90| LEE 353-Lighter Blue| | |
91 – 95| LEE 118-Light Blue| | |
96 – 100| LEE 116-Medium Blue Green| | |
101 – 105| LEE 124-Dark Green| | |
106 – 110| LEE 139-Primary Green| | |
111 – 115| LEE 089-Moss Green| | |
116 – 120| LEE 122-Fern Green| | |
121 – 125| LEE 738-JAS Green| | |
126 – 130| LEE 088-Lime Green| | |
131 – 135| LEE 100-Spring Yellow| | |
136 – 140| LEE 104-Deep Amber| | |
141 – 145| LEE 179-Chrome Orange| | |
146 – 150| LEE 105-Orange| | |
151 – 155| LEE 021-Gold Amber| | |
156 – 160| LEE 778-Mellennium Gold| | |
161 – 165| LEE 135-Deep Golden Amber| | |
166 – 170| LEE 164-Flame Red| | |

Shutter channel chart

Pattern channel chart
Your Fusion 2 has static as well as animated patterns.
Static Patterns

Animated Patterns
All Animations are available in 4 different Settings:

Standard
080| Reversed
081| Inverted
082| Inverted reversed
083
---|---|---|---
| | |

The values provide these 4 alignments.

Random Animations:
(Second Value means inverted)

Dimmer Curves

http://www.ehrgeiz.com
Ehrgeiz Lichttechnik GmbH
Im Stöckmädle 27
D- 76307 Karlsbad – Germany
Tel.: +49 7248 947 90 10
Fax: +49 7248 947 90 12
Web:www.ehrgeiz.com

References

• Manual-Hub.com - Free PDF manuals!
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>