GE Current LEDL095 LED 4 Pin Plug In Lamps Instruction Manual

LEDL095 LED 4 Pin Plug In Lamps
Instruction Manual

LEDL095 LED 4 Pin Plug In Lamps

BEFORE YOU BEGIN
To install the LED 4-pin plug-in lamps, please read the entire installation guide carefully.

The LED 4-pin plug-in lamp is not intended to be used with dimmers and emergency fixtures.
The lamp can only be used with approved ballasts. See ballast compatibility list at: www.LED.com/LED4pin-compatibility. Use of unapproved ballasts or bypassing the  original ballast will result in safety and regulation issues.

WARNING: Risk of Fire or Electric Shock. Suitable for Dry and Damp Locations. The installation must be done by qualified electricians and all safety instructions must be followed to avoid a risk of injury or property damage.

Installation Instructions

1. Switch off power to the fixture.| 2) Remove the existing fluorescent lamps from the fixture and dispose of  them properly based on local regulations.

2. For Selectable lamps only: Adjust color  temperature switch on lamp to desired setting.| 4) Check the socket condition in the fixture. If damaged or corroded, replace it with a new one. Insert Current LED 4-pin lamps. For horizontal application, rotate the lamp so the diffuser is facing towards the fixture opening. Warning: Sockets in poor condition may result in bad electrical contact, base arcing or other safety issues. Note: In two lamps condition, be sure to use Current LED 4-pin lamps in both sockets. Do not use one CFL and one LED lamp together on the same ballast as the ballast may shut down.| 5) Restore power to fixture and check for proper operation.

Note: If the lamp flickers, flashes or fails on installation, the ballast is not compatible with the lamp. Remove the lamp and check the ballast compatibility list again or contact Current for technical support at 1-800-327-0097.

CAUTION

WARNING: RISK OF FIRE OR ELECTRIC SHOCK – SUITABLE FOR DAMP LOCATIONS. Direct replacement for 13W/6T4/Q/G24q-1, 18W/7T4/Q/G24q-2,  26W/8T4/Q/G24q-3, 13W/4T4/M/GX24q-1, 18W/4.5ST4/M/ GX24q-2, 26W/5T4/M/GX24q-3 CFL lamps only. Not for use with dimmers. For use only with Compatible ballasts. See list at: www.LED.com/LED4pin-compatibility. If the lamp does not light when the luminaire is energized, or exhibits undesirable operation such as  buzzing or flickering, immediately turn off power, remove lamp from luminaire and contact lamp manufacturer or qualified electrician.
Not evaluated for use with emergency exit fixtures or emergency exit lights. Not for use with dimmers. Suitable for damp locations. For use only with compatible ballasts. See list at: www.LED.com/LED4pin- compatibility.
This device complies with Part 18 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this  device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the  manufacturer could void the user’s authority to operate the equipment. NOTE: This product complies with Part 18 of the FCC Rules but may cause interference to radios,  televisions, wireless telephones, and remote controls. Avoid placing this product near these devices. If interference occurs, move the product away from the device or plug  either into a different outlet. Do not install this product near maritime safety equipment or other critical navigation or communication equipment operating between 0.45-30 MHz. This device complies with CAN ICES- 005B.

www.LED.com
© 2022 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license.  Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 2
(Rev 11/28/22)
LEDL095

Documents / Resources

| GE Current LEDL095 LED 4 Pin Plug In Lamps [pdf] Instruction Manual
LEDL095 LED 4 Pin Plug In Lamps, LEDL095, LED 4 Pin Plug In Lamps, Plug In Lamps, Lamps
---|---

References

• LED.com/LED4pin-compatibility
• LED Commercial Lighting and Lighting Controls | Current - GLI Brands
• Commercial Lighting and Lighting Controls | Current - GLI Brands
• LED.com/LED4pin-compatibility

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>