KENWOOD X302-4 X D C Amplifier Power Channel Four Instruction Manual

KENWOOD X302-4 XDC Amplifier Power Channel Four

Product Information

Specifications

• Model: X302-4 / XM302-4 / KAC-314
• Class: D
• Channels: Four
• Dimensions
  • Length: 213 mm (8-3/8 inches)
  • Width: 149mm (5-7/8 inches)
  • Height: 53mm (2-1/16 inches)

FAQ

• Q: What should I do if the front panel gets dirty?
  • A: Turn off the power and wipe the panel with a dry silicon cloth or soft cloth. Do not use a hard cloth or volatile solvents as they can scratch the surface and peel off indicator letters.
• Q: Why should I start the engine before using the unit?
  • A: Starting the engine prevents battery depletion when using the unit in the ACC ON position.
• Q: How should I connect the speaker wires?
  • A: Connect the negative wire of the speaker or grounding speaker wires to the metal body of the car.

Accessories

• Self-tapping screws / 4
• Speaker level input cable / 1

Dimensions

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.

• Model: X302-4 / XM302-4 / KAC-314
• Serial number: …………….

Safety precautions

WARNING

To prevent injury or fire, take the following precautions:

• Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.
• When extending the ignition, battery, or ground wires, make sure to use automotive-grade wires or other wires with the range of 5 mm2 (AWG 10) or more to prevent wire deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.
• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your KENWOOD dealer.
• Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.

CAUTION

To prevent damage to the machine, take the following precautions:

• Be sure the unit is connected to a 12 V DC power supply with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

NOTE

• If you experience problems during installation, consult your KENWOOD dealer.
• If the unit does not seem to be working right, consult your KENWOOD dealer.

Cleaning the unit

• If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.

CAUTION

• Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol.
• They can scratch the surface of the panel and / or cause the indicator letters to peel off.

To prevent battery rise

• When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.

Protection function

The protection function is activated in the following situations:

This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the power indicator goes off and the amplifier stops operating.

• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent to the speaker output.
• When the internal temperature is high and unit won’t operate.

Wiring

• Take the battery wire for this unit directly from the battery. If it’s connected to the vehicle’s wiring harness, it can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire.
• Do not allow the wire to directly contact the edge of the iron plate by using Grommets.
• Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative ⊖ terminal. Do not turn the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger.
• For the power cord and ground, use a vehicle type (fireproof ) power wring cord. (Use a power wiring cord with the range of 5 mm2 (AWG 10) or more.)
• When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.

Speaker selection

• Using speakers with smaller input ratings than the amplifier’s output power would result in smoke generation or equipment failure.
• The impedance of the speakers that are going to be connected should be 2 Ω or greater (for stereo connections), or 4 Ω or greater (for bridged connections). When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.

< Example>

Installation

XM302-4

NOTE

• After wiring, fix the protective cover securely with screws and washers.

Installation procedure

Since there are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection.

1. Remove the ignition key and disconnect the negative ⊖ terminal of the battery to prevent short circuits.
2. Set the unit according to the intended usage.
3. Remove the Dressing cover.
4. Connect the input and output wires of the units.
5. Connect the speaker wires.
6. Connect the power wire, power control wire and grounding wire following this order.
7. Install the installation fittings in the unit.
8. Attach the unit.
9. Attach the Dressing cover.
10. Connect the negative ⊖ terminal of the battery.

CAUTION

• Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)
• Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.
• Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit.
• The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.
• When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.
• Do not install near the dashboard, rear tray, or air bag safety parts.
• The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.
• After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.

Connections

WARNING

• Remove the ignition key and disconnect the negative ⊖ terminal of the battery to prevent short circuits.

In a computer-equipped vehicle, when you remove the ⊖ terminal of the battery, the memory may disappear, or a defect may occur in the electrical system of the vehicle. Consult your dealer for further details.

WARNING

• Particular attention must be given to making good electrical contact at the amplifier-output and speaker terminals.
• Poor or loose connections can cause sparking or burning at the terminals because of the very high power that the amplifier can deliver.

CAUTION

• If sound is not output normally, immediately turn power off and check connections.
• Be sure to turn the power off before changing the setting of any switch.
• If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.
• Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits.
• Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.
• After installation, check that the brake lamps, turn signal lamps and windshield wipers work properly.

Power wire and speaker wire connection

RCA INPUT connection

Speaker level input connections

NOTE

• Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage.

Cable color of the connector

System examples

4-channel system

2-channel + Subwoofer system

FCC STATEMENT

For U.S.A.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Supplier’s Declaration of Conformity

• Trade Name: KENWOOD
• Products: CLASS D FOUR CHANNEL POWER AMPLIFIER
• Model Name: X302-4 / XM302-4 / KAC-314
• Responsible Party: JVCKENWOOD USA CORPORATION 4001 Worsham Avenue, Long Beach, CA 90808, U.S.A. PHONE: 1-800-252-5722

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

For Europe

X302-4 only

Declaration of Conformity with regard to the EMC Directive 2014/30/EU
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU

Manufacturer:

• JVCKENWOOD Corporation
• 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
• Kanagawa, 221-0022, JAPAN

EU Representative

• JVCKENWOOD Europe B.V.
• Rendementsweg 20 B-9, 3641 SL Mijdrecht, THE NETHERLANDS

X302-4 only

Declaration of Conformity with regard to the Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091)
Declaration of Conformity with regard to the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (S.I. 2012/3032)

Manufacturer:

• JVCKENWOOD Corporation
• 3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, JAPAN

UK Importer:

• JVCKENWOOD U.K. Limited
• First Floor, Gleneagles, the Belfry, Colonial Way, Watford, Hertfordshire WD24 4WH, UNITED KINGDOM

Information on Disposal of Old Electrical and Electronic Equipment (applicable for countries that have adopted separate waste collection systems)

Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.

Controls

This is a 4 channel amplifier including 2 stereo amplifiers in a body. One amplifier is referred to as amplifier A and the other is amplifier B. This unit is compatible with a large variety of systems by combining the switches and functions described in the following.

1. Fuse (20 A × 2)

   • NOTE: If you can’t find the specified capacity fuse at your store etc., consult your KENWOOD dealer.

2. Battery terminal (POWER IN BATT.)

3. Power control terminal (P.CON)

   • Controls the unit ON / OFF.

4. Ground terminal (GND)

5. SPEAKER OUTPUT terminals (A.ch / B.ch)

   • Stereo connections: When you wish to use the unit as a stereo amplifier, stereo connections are used. The speakers to be connected should have an impedance of 2 Ω or greater. When multiple speakers are to be connected, ensure that the combined impedance is 2 Ω or greater for each channel.
   • Bridged connections: When you wish to use the unit as a high-output amplifier, bridged connections are used. (Make connections to the LEFT channel ⊕ and the RIGHT channel ⊖ SPEAKER OUTPUT terminals.) The speakers to be connected should have an impedance of 4 Ω or greater. When multiple speakers are to be connected, ensure that the combined impedance is 4 Ω or greater.

6. SP LEVEL INPUT terminal

   • The output from the FACTORY INSTALLED HEAD UNIT up to 50 W can be input. The power is turned on and off as the unit detects input signal (SIGNAL SENSING TURN-ON). Therefore it is not necessary to connect the power control wire.

7. LINE IN terminal (A.ch / B.ch)

8. INPUT SENSITIVITY control (A.ch / B.ch)

   • Set this control according to the pre-output level of the HEAD UNIT connected with this unit.
   • NOTE: For the pre-output level, refer to the “Specifications” in the instruction manual of the HEAD UNIT.

9. BASS BOOST LEVEL control (B.ch)

   • Sets the low frequency level to be compensated.

10. FILTER switch (A.ch / B.ch)
    This switch allows to apply high-pass or low-pass filtering to the speaker outputs.

    • HPF (High-Pass Filter) position: The filter outputs the band of higher frequencies than the frequency set with the “FILTER FREQUENCY” control.
    • OFF position: The entire bandwidth is output without filtering.
    • LPF (Low-Pass Filter) position: The filter outputs the band of lower frequencies than the frequency set with the “FILTER FREQUENCY” control.

11. FILTER FREQUENCY control (A.ch / B.ch)

    • Sets the cutoff frequency when the “FILTER” switch is set to “HPF” or “LPF”.

12. Power indicator

    • When the power is turned on, the Power indicator lights.

The product with this logo is conformed to Hi-Resolution Audio standard defined by Japan Audio Society. This logo is used under license from Japan Audio Society.

It is recommended that a car audio system should be configured with all High- Resolution Audio compatible products from player to speaker to enjoy its high- quality sound.

Specifications

Specifications subject to change without notice.

Audio section

• Rated power output: (+B = 14.4 V)
• Stereo (4 Ω) ………………. 50 W × 4 (20 Hz–20 kHz, ≤ 1.0% THD)
• Stereo (2 Ω) ………………………………..75 W × 4 (1 kHz, ≤ 1.0% THD)
• Bridged (4 Ω) …………………………..150 W × 2 (1 kHz, ≤ 1.0% THD)
• Speaker impedance …………………………4 Ω (2 Ω to 8 Ω allowable)
  • (Bridged connection: 4 Ω to 8 Ω allowable)
• Frequency response (+0, −3 dB) ………………………….20 Hz–50 kHz
• Input sensitivity (RCA) ……………………………………………………0.2 V–5.0 V
• Signal to noise ratio ……………………………………………………………….100 dB
• Input impedance ……………………………………………………………………… 10 kΩ
• Low pass filter frequency (−12 dB / oct.) ……………………………………………………………50 Hz–200 Hz (variable)
• High pass filter frequency (−12 dB / oct.) ……………………………………………………………50 Hz–200 Hz (variable)
• Bass boost control (40 Hz / B channel) ………………………………………………………….0 – +18 dB (variable)

General

• Operating voltage ………………………………………….12 V DC car battery

• Current consumption ……………………………………………………………….. 20 A

• Dimensions (W × H × D) ………………………………..213 × 53 × 149 mm

  • 8-3/8 × 2-1/16 × 5-7/8 inch

• Weight …………………………………………………………………………..1.4 kg (3.1 lbs)

• Maximum Dynamic Power: 65 Watts × 4 at 1 kHz, 4 Ohms and ≤10% THD+N

• Continuous Power Output: 50 Watts RMS × 4 at 1 kHz, 4 Ohms and ≤1% THD+N 84 dBA Reference 1 Watt RMS

US Residence Only

Register Online

• Register your Kenwood product at www.kenwood.com/usa

© 2021 JVCKENWOOD Corporation

References

• KENWOOD USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>