GSD WKXT08M2501 WIFI+BT Module User Manual

GSD WKXT08M2501 WIFI+BT Module

Specifications

• Model : WIFI+BT Module
• Product Name : WKXT08M2501(L)
• Standard Interface : USB
• Data Transfer Rate: 1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120 and maximum of 1201Mbps
• Modulation Method: GFSK, /4-DQPSK, 8DPSK (Bluetooth); DQPSK, DBPSK, CCK (802.11b); QPSK, BPSK, 16QAM, 64QAM with OFDM (802.11g); QPSK, BPSK, 16QAM, 64QAM with OFDM (802.11n); QPSK, BPSK, 16QAM, 64QAM with OFDM (802.11a); QPSK, BPSK, 16QAM, 64QAM, 256QAM with OFDM (802.11ac); QPSK, BPSK, 16QAM, 64QAM, 256QAM, 1024QAM with OFDM (802.11ax); BLUETOOTH
• Frequency Band: 2402~2480 MHz
• Operation Mode : Security
• Operating Voltage: Not specified
• Current Consumption: Not specified
• Antenna Type: Not specified
• Operating Temperature: Not specified
• Storage Temperature: Not specified
• Humidity: 5 to 95% maximum (non-condensing)

Product Description

The WKXT08M2501(L) WIFI+BT Module is a wireless module that complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax for 5GHz Wireless LAN. It also features Bluetooth v5.2 technology. With two transmit and two receive paths (2T2R), it provides a high-speed transfer rate of up to 1201 Mbps in 802.11ax mode. The module works with all existing network infrastructure and supports up to 128-bit WEP Encryption for secure connections. It is compatible with operating systems such as Linux, Win7, Win8, Win10, and XP. The module is designed for easy installation and configuration, featuring a high-speed USB 2.0 interface.

Product Features

• Complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax for 5GHz Wireless LAN.
• Bluetooth v5.2 technology.
• Two transmit and two receive paths (2T2R).
• Works with all existing network infrastructure.
• Capable of up to 128-bit WEP Encryption.
• Freedom to roam while staying connected.
• Up to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
• Operating Systems: Linux, Win7, Win8, Win10, XP.
• Low power consumption.
• Easy to install and configure.
• High-speed USB 2.0 interface.

Hui Zhou Gaoshengda Technology Co., LTD

• WIFI+BT Module
• IEEE 802.11 a/b/g/n/ac/ax 2T/2R
• Model Number: WKXT08M2501(L)

Product Description

The WKXT08R2501 is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11ax MAC/baseband/radio and Bluetooth
The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE 802.11 a/b/g/n/ac/ax feature-rich wireless connectivity at high standards, and delivers reliable, cost- effective, throughput from an extended distance.

Product Features

• Complies with IEEE 802.11b/g/n/ax for 2.4GHz and IEEE 802.11a/n/ac/ax 5GHz Wireless LAN.
• Bluetooth v5.2
• Two transmit and Two receive path(2T2R)
• Works with all existing network infrastructure.
• Capable of up to 128-Bit WEP Encryption.
• Freedom to roam while staying connected.
• UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
• Operating Systems：Linux,Win7, Win8, Win10,XP
• Low power consumption.
• Easy to install and configure.
• High speed USB 2.0 interface

Product Specification

of 1201Mbps
Modulation Method| GFSK,π/4-DQPSK,8DPSK(bluetooth) DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)

QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac) QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDM (802.11ax)

Frequency Band| BLUETOOTH 2402~2480 MHz

WIFI

2.4G: 2412~2462 MHz

5G: 5180~5320MHz, 5500~5825MHz

Operation Mode| Infrastructure
Security| WEP, TKIP, AES, WPA, WPA2
Operating Voltage| 3.3V±10%
Current Consumption| ＜1000mA
Antenna Type| PCB Antenna
Operating Temperature| 0 ~ 70°C ambient temperature
Storage Temperature| -40 ~ 80°C ambient temperature
Humidity| 5 to 95 % maximum (non-condensing)

NOTICE

• please keep this product and accessories attached to the places which children can’t touch;
• do not splash water or other liquid onto this product, otherwise it may cause damage;
• do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
• please keep this product away from flammable or naked flame;
• please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
• This radio transmitter FCC ID: 2AC23-WKXT08 has been approved by the Federal Communications Commission to operate with the integrated PCB antenna. Use of any other antenna is strictly prohibited without filing an application for a new system-specific FCC ID.
• The module complies with FCC Part 15.247 / Part 15.407 and applies for Single module approval.
• Trace antenna designs: Not applicable – the antenna is integrated into the module and cannot be modified. See section 2.3.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antenna type and antenna gain

• The radio transmitter has been approved to operate with the antenna integrated into the module. Use of any other antenna, or modifying the antenna design on the module, is strictly prohibited and voids the FCC / ISED Canada modular certification.
• Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2AC23-WKXT08L” Any similar wording that expresses the same meaning may be used.
• Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually.
• If the modular transmitter has been fully tested by the module grantee on the required number of channels, modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions).
• The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important
• when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration.
• Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
• The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
• The host manufacturer is recommended to use D04 Module Integration Guide recommended as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.
• This module is stand-alone modular. If the end product will involve Multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Canada Statement

This device complies with Industry Canada’s license-exempt RSSs.

Operation is subject to the following two conditions

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

BT Antenna

Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as
show in this manual(FCC/ICanada statement).

• Host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15 B, ICES 003.
• Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.
• The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
• This module is stand-alone modular. If the end product will involve the Multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult
• with module manufacturer for the installation method in end system.

Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.

Must have on the host device a label showing Contains FCC ID:2AC23-WKXT08L or IC: 12290A-WKXT08L.
Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.

The installer should put it in the manual

Documents / Resources

| GSD WKXT08M2501 WIFI+BT Module [pdf] User Manual
WKXT08M2501 WIFI BT Module, WKXT08M2501, WIFI BT Module, BT Module, Module
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>