QSFPTEK S5300-24P4TS 24 Port Gigabit Ethernet L2+ Switch User Guide
- June 17, 2024
- QSFPTEK
Table of Contents
**QSFPTEK S5300-24P4TS 24 Port Gigabit Ethernet L2+ Switch User Guide
**
Introduction
The S5300-24P4TS is a managed Ethernet L2+ access PoE+ switch with 24x
10/100/1000BASE-T RJ45 PoE+ ports and 4x 1G RJ45/SFP combo ports, supporting
OSPF. This 24 port PoE switch, supporting a switching capacity of up to 56
Gbps and a forwardingrateof 42 Mpps for stable transmission, functioning as a
Power Sourcing Equipment (PSE), deliversboth power and data over one Ethernet
cable to Powered Devices (PDs) such as Wireless APs,
IP security cameras, and VoIP phones. Its integrated power and data delivery
simplifies
installation, reduces costs, and provides a cost-effective SMB secure wireless
solution. TheS5300-24P4TS PoE+ switch is an excellent choice for enterprise
network requirements, surveillance systems, and SMBs.
We appreciate your decision to select S5300-24P4TS. This manual is intended to help youbecome acquainted with the switch design and provide instructions for implementing the switches into your network
Accessories
Power Cord x1
Console Cable x1
Mounting Bracket x2
M3 Screw x6
Rubber Pad x4
Hardware Overview
**Front Panel Ports
**
Ports | Description |
---|---|
RJ45 | 1000BASE-T ports for Ethernet connection and supports up to 30WPoE+ |
SFP | Hot-swappable SFP ports for 1G connection |
CON | An RJ45 console port for serial management |
**Front Panel LEDs
**
LEDS | Status | Description |
---|---|---|
1-24 | Green | On |
Off | Off: no signal transmission | |
Orange | On | Always on in orange: 10/100M |
Off | Off: no signal transmission | |
25S-28S | Green | On |
Off | Off: no signal transmission | |
25T-28T | Green | On |
Off | Off: no signal transmission | |
Reset | / | / |
thesystem will return to the default setting.
SYS LED| /| /| If the SYS indicator flickers, thesystem works normally.
PWR LED| /| /| f the PWR indicator is always on, the device is powered on.
---|---|---|---
Back Panel
Installation Requirements
Tools Preparation
- Screwdriver
- Static-proof wristband
- Bolt
- Ethernet cable
- Other Ethernet terminal devices
- Control terminal
Safety Principles
Keep dustless and clean during or after the installation.
- Put the cover in a safe place.
- Put tools in the right place where they are not easily falling down.
- Put on relatively tight clothes, fasten the tie or scarf well and roll up the sleeve, avoidingstumbling the machine box.
- Put on protective glasses if the environment may cause damage to your eyes.
- Avoid incorrect operations that may cause damage to humans or devices
Site Environment
- Make sure that the workshop is well-ventilated, the heat of electrical devices is well- discharged
- Avoid damaging devices by following the electrostatic discharge prevention procedure.
- S5300-24P4TS Hardware Installation Manual
- Put the machine box in a place where cool air can blow off the heat inside the machinebox. ‘
- Make sure the machine box is sealed
Mounting the Switch
**Connecting the Power
**
- Plug the AC power cord to the switch power port on the back rear.
- Connect the other end of the power cord to an AC power source equipment.
**Connecting the RJ45 Ports
**
- Connect one end of the Ethernet cable to the RJ45 port on networking equipment, suchasPC, printer, server, storage, etc.
- Connect the other end of the Ethernet cable to
**Connecting the SFP Port
**
- Insert the SFP module into the SFP port.
- Plug a fiber patch cable into the SFP transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
**Connecting the Console Port
**
- Prepare a console cable.
- Insert the RJ45 connector of the console cable into the console port on the switch.
- Connect the DB9 female connector on the other end of the console cable to the serial port
on the computer host
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and
open a web browser.
Step 2 : Set the IP address of the computer to 192.168.0.x (where “x” is
any number from2to254)
and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address
bar. Enter the default
username and password (admin/admin).
Step 4 : Click sign-in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to directly connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.
Step 4 : Enter the default username and password (admin/admin)
Troubleshooting
Hardware Fault Analysis
- Power and cooling systems—power and fan
- Port, cable and connection—ports on the front panel of the switch and the cables connectingthese ports
Faults Relative to Power and Cooling System
Do the following checkups to help remove the fault:
- When the power on-off is at the “ON” location, check whether the fan works normally. If thefandoes not work well, check the fan.
- If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
- If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative to Port, Cable and Connection
Do the following checkups to help remove the fault:
- If the port of the switch cannot be linked, check whether the cable is correctly disconnectedness the peer connection is normal.
- If the power on-off is at the “ON” location, check the power source and the power cable.
- If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
- Contact us https://www.qsfptek.com/company/contact-us.html
- Customer Succes s https://www.qsfptek.com/resources/customer-success-stories
- Email: support@qsfptek.com
Product Warranty
S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. Youareeligible to apply for a return within 14 days and exchange within 90 days of receiving them
For more details about applying qualifications, please live chat or email sales@qsfptek.comfor support
**5 Year Warranty
14-day Return Window
**
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>