THIRTY7 Components T7-WPFH01 Front Fork Suspension Holder

Product Information

Product Name: THIRTY7 Motorsport Components Front Fork Suspension Holder

• Model Number: T7-WPFH01
• Website: t7components.com
• Email: info@t7components.com
• Social Media: @thirty7_official

Instructions
Thank you for choosing THIRTY7 Components! We appreciate your business, and your feedback is crucial to us. Please take a moment to read the instructions carefully to get the most out of your product. If you are satisfied with your purchase, please consider tagging us on social media platforms using the hashtag #thirty7_official.

Warning and Disclaimer
Please note that the product is subject to the following warning and disclaimer:

• Read and follow all instructions and warnings provided with the product.
• Failure to follow the instructions may result in damage to the product or injury to the user.
• THIRTY7 Components is not responsible for any damages or injuries caused by improper use of the product.

Product Usage Instructions

Preparation
Before installing the THIRTY7 Motorsport Components Front Fork Suspension Holder, make sure you have the following tools:

• Socket wrench set
• Torque wrench
• Grease
• Clean cloth

Ensure that you have a clean and well-lit workspace to work on your bike.

Removal of Existing Front Fork Suspension
If there is an existing front fork suspension on your bike, follow these steps to remove it:

1. Refer to your bike’s user manual or consult a professional to identify the correct procedure for removing the front fork suspension.
2. Use the appropriate tools to loosen and remove any bolts or fasteners securing the front fork suspension to your bike.
3. Gently lower the front fork suspension out of its mounting position and set it aside.

Installation of THIRTY7 Front Fork Suspension Holder

]Follow these steps to install the THIRTY7 Motorsport Components Front Fork Suspension Holder:

1. Clean the mounting area on your bike where the front fork suspension holder will be installed.
2. Apply a small amount of grease to the mounting area to ensure smooth installation.
3. Align the THIRTY7 Front Fork Suspension Holder with the mounting area and insert the bolts provided.
4. Tighten the bolts using a torque wrench to the recommended torque specifications provided in your bike’s user manual or as specified by THIRTY7 Components.

Final Checks and Adjustment
After installing the THIRTY7 Front Fork Suspension Holder, perform the following checks and adjustments:

• Ensure that all bolts are securely tightened.
• Check for any interference or misalignment of the front fork suspension holder.
• If necessary, make any required adjustments or seek professional assistance.

Specifications

• Product Type: Front Fork Suspension Holder
• Compatibility: Compatible with select bike models (refer to product documentation for compatibility list)
• Material: High-strength alloy
• Weight: X grams
• Color: X

FAQ

Can the THIRTY7 Front Fork Suspension Holder be used on any bike?
The THIRTY7 Front Fork Suspension Holder is compatible with select bike models. Please refer to the product documentation or contact THIRTY7 Components for a compatibility list.

What torque should I use to tighten the bolts?
Refer to your bike’s user manual or the torque specifications provided by THIRTY7 Components for the recommended torque settings.

Is any special maintenance required for the THIRTY7 Front Fork Suspension Holder?
The THIRTY7 Front Fork Suspension Holder does not require any special maintenance. However, it is recommended to periodically check the bolts for tightness and ensure there is no damage or wear on the holder.

Can I install the THIRTY7 Front Fork Suspension Holder myself?
Installation of the THIRTY7 Front Fork Suspension Holder requires basic mechanical knowledge and tools. If you are unsure or unfamiliar with bike mechanics, it is recommended to seek professional assistance for installation.

Thank you for choosing THIRTY7 Components! We appreciate your business, and your feedback is crucial to us. Please take a moment to read the instructions carefully to get the most out of your product. If you are satisfied with your purchase, please consider tagging us on social media platforms.

thirty7_official

INSTRUCTIONS

• The Suspension Holder is designed for specific suspensions only, with 59-60 mm diameter in the area where suspensions are clamped in the bottom triple clamp from brands such as WP, KYB, Showa, and Ohlins.
• The holder must be fastened to the wall/suspension bench using screws or bolts through the designated opening hole at the back. Screws or bolts are not included.
• After the holder has been mounted, you can simply clip the suspension in place.
• If you have any questions about the product, please contact us at support@t7components.com.

WARNING AND DISCLAIMER
Please be advised that any parts manufactured, designed or sold by THIRTY SEVEN COMPONENTS (THIRTY7) should only be installed by a licensed motorcycle technician or dealer. Motorcycles are inherently dangerous, and using them improperly can result in serious injury, death, or damage to property. THIRTY7 is not responsible for any damage or injury that may result from misuse or improper installation of aftermarket parts. Customers must exercise caution and good judgment when selecting, installing, and maintaining THIRTY7 products. In the event of a defect in the material or design of any part, THIRTY7 will either refund the purchase price or replace the part within thirty (30) days of purchase, subject to inspection. Please note that any attempts to modify or repair THIRTY7 products will void this warranty. THIRTY7 is not liable for any incidental or consequential damages, property damage, personal injury damage, or any other kind of damage or expense. By purchasing a THIRTY7 product, you acknowledge and agree to these terms and conditions. THIRTY7 makes no other warranties, express or implied, including without limitation any warranties of merchantability and fitness for a particular purpose. We reserve the right to alter the terms, conditions, and notices under which our products are offered

• PN: T7-WPFH01
• t7components.com
• info@t7components.com
• @thirty7_official

QR CODE

Documents / Resources

| THIRTY7 Components T7-WPFH01 Front Fork Suspension Holder [pdf] Instructions
T7-WPFH01 Front Fork Suspension Holder, T7-WPFH01, Front Fork Suspension Holder, Fork Suspension Holder, Suspension Holder, Holder
---|---

References

• THIRTY SEVEN COMPONENTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>