FISHER PAYKEL DD60DDF Double DishDrawer Dishwasher User Guide
- June 17, 2024
- Fisher & Paykel
Table of Contents
DD60DDF Double DishDrawer Dishwasher
DOUBLE DISHDRAWERTM DISHWASHER
Specifications
- Model: DD60DDF
- Installation Guide: NZ AU GB IE SG 591384C05.19
1. Safety and Warnings
! WARNING!
IMPORTANT SAFETY INSTRUCTIONS
Installation of this dishwasher requires basic mechanical and
electrical skills.
Be sure to leave these Instructions with the Customer. Installation
must comply with your local building and electricity
regulations.
At the completion of the dishwasher installation, the Installer
must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF.
It is the responsibility of the plumber and electrician to ensure
that each installation complies with all Codes and Regulations.
WARNING–Improper connection of the equipment-earthing
conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative if you
are in doubt as to whether the appliance is properly earthed.
The dishwasher MUST be installed to allow for future removal from
the enclosure if service is required.
The switched power outlet must be outside the dishwasher cavity, so
that it is accessible after installation.
Care should be taken when the appliance is installed or removed to
reduce the likelihood of damage to the power supply cord and
hoses.
Do not modify the power supply plug provided with the appliance–if
it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
Do not use an extension cord, adapter plug, or multiple outlet
box.
If the dishwasher is to be relocated from one installation to
another, it must be kept upright to avoid damage from water
spillage.
Failure to follow this advice may result in electrical shock or
death.
Make sure only new hoses are used for connection (supplied with the
dishwasher). Old hoses should not be reused.
! WARNING!
Failure to install the dishwasher correctly could invalidate any
warranty or liability claims.
Cut Hazard: Take care–panel edges are sharp. Failure to use
caution could result in injury or cuts.
If the product is installed in a motor vehicle, boat, or similar
mobile facility, you must bring the vehicle, boat, or mobile
facility containing the product to the service shop at your expense
or pay the service technician’s travel to the location of the
product.
2. Parts Supplied
-
Drain hose support (1)
-
Drain hose joiner (1)
-
Wire clip (2) (for securing Drain hose joiner)
-
Clamp (1) (for securing Drain hose joiner)
-
Side mounting bracket kit (A and B) (2) OPTIONAL
-
Top mounting brackets (2) OPTIONAL
-
Phillips 16 mm screws (9)
-
Rubber washer for inlet hose (1) (comes already fitted)
-
Moisture protection tape (1) (to prevent moisture damage to
cabinetry) -
Hexagonal socket for feet adjustment (2) (long &
short) -
Prefinished toekick (1)
3. DishdrawerTM Installation Overview
This video provides an overview of what is needed to install a
DishDrawerTM. It is intended as an overview only of the
installation process and is not intended to be used as a guide on
how to install a DishDrawerTM yourself.
FAQ
-
1. What are the basic mechanical and electrical skills requiredfor installation?
The basic mechanical skills required for installation include
knowledge of using tools like screwdrivers and wrenches. The basic
electrical skills required include knowledge of wiring and
connections.
-
1. Can I reuse old hoses for connection?
No, it is recommended to use only new hoses supplied with the
dishwasher for connection. Reusing old hoses can lead to potential
leaks or damage.
-
1. How should I handle the dishwasher during installation orremoval?
Take care when handling the dishwasher during installation or
removal to reduce the likelihood of damage to the power supply cord
and hoses.
-
1. Can I modify the power supply plug?
No, it is not recommended to modify the power supply plug
provided with the appliance. If it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
-
1. What should I do if I want to relocate the dishwasher?
If you want to relocate the dishwasher from one installation to
another, make sure to keep it upright to avoid damage from water
spillage.
DOUBLE DISHDRAWERTM DISHWASHER
DD60DDF models
INSTALLATION GUIDE NZ AU GB IE SG 591384C05.19
1SAFETY AND WARNINGS
! WARNING!
IMPORTANT SAFETY INSTRUCTIONS
Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.
Installation of this dishwasher requires basic mechanical and electrical
skills.
Be sure to leave these Instructions with the Customer. Installation must
comply with your local building and
electricity regulations. At the completion of the dishwasher installation,
the Installer must perform the Final Checklist. Remove all packaging materials
supplied with
the dishwasher. This dishwasher is manufactured for indoor use only. Ensure
all water connections are turned OFF.
It is the responsibility of the plumber and electrician to ensure that each
installation complies with all Codes and Regulations.
WARNING–Improper connection of the
The dishwasher MUST be installed to allow for future
equipment-earthing conductor can result in a
removal from the enclosure if service is required.
risk of electric shock. Check with a qualified
The switched power outlet must be outside
electrician or service representative if you
the dishwasher cavity, so that it is accessible
are in doubt as to whether the appliance is
after installation.
properly earthed.
Care should be taken when the appliance is installed
Do not modify the power supply plug
or removed to reduce the likelihood of damage to the
provided with the appliance–if it will not fit
power supply cord and hoses.
the outlet, have a proper outlet installed by a
If the dishwasher is to be relocated from one
qualified electrician. Do not use an extension
installation to another it must be kept upright to
cord, adapter plug or multiple outlet box.
avoid damage from water spillage.
Failure to follow this advice may result in
Make sure only new hoses are used for connection
electrical shock or death.
(supplied with the dishwasher). Old hoses should not
be reused.
! WARNING!
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.
Cut Hazard Take care–panel edges are sharp. Failure to use caution could result in injury or cuts.
If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.
1
2PARTS SUPPLIED
Drain hose support (1)
Drain hose joiner (1)
Wire clip (2) (for securing Drain hose joiner)
Clamp (1) (for securing Drain hose joiner)
Side mounting bracket kit (A and B) (2) OPTIONAL
Top mounting brackets (2) OPTIONAL
Phillips 16 mm screws (9)
Rubber washer for inlet hose (1) (comes already fitted)
Moisture protection tape (1) (to prevent moisture damage to cabinetry)
Hexagonal socket for feet adjustment (2) (long & short)
Prefinished toekick (1)
DishdrawerTM installation overview This video provides an overview of what is
needed to install a DishDrawerTM. It is intended as an overview only of the
installation process and is not intended to be used as a guide on how to
install a DishDrawerTM yourself. https://vimeo.com/325297597
If the Drain hoses supplied are not long enough to reach your services, you
must use a Drain Hose Extension Kit P/N 525798 which will extend the drain
hoses by 3.6 m. The kit is available from the nearest Fisher & Paykel
Authorised Service Centre or our website.
IMPORTANT! SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all
markets and are subject to change at any time. For current details about model
and specification availability in your country, go to our website
fisherpaykel.com or contact your local Fisher & Paykel dealer.
2
H K
I
FRONT
B
J G
D E
O
PLAN 3
3PRODUCT DIMENSIONS
C
A
F
L
PROFILE
M
N
PRODUCT DIMENSIONS A Overall height of product1 B Overall width of product C
Overall depth of product D Depth of chassis (to back of front drawer panel) E
Depth of drawer front panel F Height of chassis1 G Height of drawer front
panels H Height of upper drawer front panel I Height of lower drawer front
panel J Height from top of drawer front panel to top of chassis K Ventilation
gap between drawer front panels L Height of toekick (customisable) M Depth
from front of drawer panel to front of toekick (adjustable)3 N Height of
levelling feet (adjustable) O Maximum extension of drawer
1 includes 2mm high bracket slots2 depending on adjustment of levelling feet 3
adjustable to match toekick recess on adjoining cabinetry
DD60DDF MM
820-8802 599 573 553 20 811 717 398 312 2 8
70-120 38-54 9-692
547
4CABINETRY DIMENSIONS
Q
Bracket slots
PLAN
CABINETRY DIMENSIONS P Inside height of cavity Q Inside width of cavity R
Inside depth of cavity S Recommended height of adjacent cabinet space T Height
of toekick space
- depending on adjustment of levelling feet
R
DD60DDF MM
min. 820 600
min. 560 720
100-160
S P
T
PROFILE
Minimum clearances from adjacent cabinetry
min. 13 mm clearance from a corner cupboard
min. 2 mm clearance to adjacent cupboard door
4
COUNTERTOP
10 mm
Moisture protection tape must be applied.
5 CAVITY PREPARATION
These marks indicate formed bracket screw locations, if securing by drawer
removal.
If there is no side partition, you can construct timber bracing as something
to secure into.
WARNING!
Incorrect placement of the hole will result in damage to hoses.
Ø 57mm
max. 450mm
Max 5mm Max distance between hole edge and rear inner face
Max 10mm Max distance between hole edge and floor
5
Service Holes Can be located either side of dishwasher, close to the rear face and the floor, as illustrated, for access to the water supply and drain. If the hole is through wood, make sure its edges are smooth and rounded. If the hole is through metal, ensure you fit the supplied Edge Protector to prevent damage to the power cord.
min. (200mm
Water Connection
Recommended COLD (Maximum 60°C).
3/4″ BSP (GB20) to suit flat washer.
Water Pressure
Water softener models Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi)
Models without water softener Max. 1 MPa (145 psi) Min. 0.03 MPa (4.3 psi)
Kosher requirements
Drains will need to be separated to satisfy kosher requirements. We suggest
you confirm acceptability with your local rabbi in respect to kosher
installations.
IMPORTANT!
The power outlet must be located in a cabinet adjacent to the dishwasher
cavity. 220-240 VAC min. 9.5 A
6 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE
LEFT HAND SIDE
Drain hoses–2000mm Inlet hose–1650mm
Power cord (excl.plug)–1650mm
RIGHT HAND SIDE
Drain hoses–1800mm Inlet hose–1250mm Power cord (excl.plug)–1650mm
6
NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR
CABINETRY…
7 RECOMMENDED METHOD (A)–SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY
ONLY)
8-AATTACH SIDE MOUNTING BRACKETS
Clip all four side mounting brackets
into their slots using a flat-bladed
screwdriver. Ensure they’re securely
B
fitted before sliding product into cavity.
A
B A
A B
A
B
The mounting slots are in pairs, one on each side diagonally across the product. A bracket must match A slot and B bracket must match B slot.
When fitting brackets, ensure the ends are not pushed down into the chassis.
7
9-APULL THROUGH HOSES & PUSH INTO THE CAVITY
Optionally attach the two top mounting brackets
(x2)
When fitting brackets, ensure the ends are not pushed down into the chassis.
Initially level the product
You can raise or lower the product by twisting the feet. Then take care when pushing the product into the cavity that you do not bend the feet.
As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.
!0-ASECURE TO THE CABINETRY ON THE SIDES
Open the drawer halfway. Using a flat bladed
screwdriver, prise the grey rubber plug out of the trim moulding.
2
Using a small Philips screwdriver, screw through the trim
moulding, securing the side mounting bracket
to the cabinetry. Do not damage the
rubber trimseal.
1
Replace the grey rubber plug back into the trim moulding and ensure the trim
seal is facing forward.
3
Repeat for all four brackets.
!1-AOPTIONALLY SECURE TO THE CABINETRY ABOVE
(x2)
The top mounting brackets will only bend upwards a maximum of 10 mm.
!2-AAFTER SECURING, REFER TO `FIT THE SUPPLIED TOEKICK PANEL’ STEP
8
7 ALTERNATIVE METHOD (B)–SECURE BY DRAWER REMOVAL
8-BPULL THROUGH HOSES & PUSH INTO THE CAVITY
optionally attach the two top mounting brackets
(x2)
When fitting brackets, ensure the ends are not pushed down into the chassis.
Initially level the product
9-BREMOVE THE LOWER DRAWER
To prevent kinked hoses Either sit the drawer down on the left hand side
(recommended) or rotate the drawer clockwise, resting it on its side after
removal.
3
You can raise or lower the product by twisting the feet. Then take care when
pushing the product into the cavity that you do not bend the feet.
9
As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.
1
2
100 mm
Press the release tabs in on either side and push back to release drawer from runners. Lift drawer off runners.
Sit the drawer down
4
Push drawer runners back in on either side.
3
Rotate the drawer clockwise (max. 90o) and rest on side.
4
Push drawer runners back in on either side.
!0-BSECURE TO THE CABINETRY ON THE SIDES
For further adjustment, using the most appropriate length Hexagonal socket
supplied, fully extend levelling feet up to required distance by hand.
!1-BOPTIONALLY SECURE TO THE CABINETRY ABOVE
(x2)
The top mounting brackets will only bend upwards a maximum of 10 mm.
Secure using two pairs of formed brackets. Repeat on the other side of the chassis.
x4
Hexagonal socket
Ensure product is level and aligning with cabinetry.
!2-BREFIT THE DRAWER ONTO THE RUNNERS
2
Lift or rotate anti-clockwise the
4
drawer back onto the drawer runners on either side.
100 mm
Before refitting the
3
drawer, ensure the hoses
are not twisted and the
latches at the rear of each drawer runner are
1
facing forward.
Pull the release tabs forward on both sides 100 mm. Ensure the tabs are fully pulled forward and click into place.
Release tab
10
!3 FIT THE SUPPLIED TOEKICK PANEL
Where the toekick
meets the bottom
3
of the tub is the
cut-off point
1
Lay the toekick face down on a chopping board or similiar
2 4 19
5
19 Turn the toekick over and score along the same line
6
Mark this point on the toekick with a pencil
Score along the marked cutoff line with a knife
Gently snap off the excess
Mounting rail
7
Smooth the edges with a file. Be careful of sharp edges.
8
Snap off the two end tabs
9
Slide the toekick onto the mounting rails either side and screw the toekick
onto the bottom of tub on either side.
IMPORTANT!
Do not overtighten screw.
11
!4 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
DRAINAGE OPTION 1 Dishwasher and 38 mm Standpipe
Screw Drain hose support to back wall
at correct height.
If space is limited for fixing, push
hose through drain hose support
to required height. 2
max. 120 mm
750-883 mm
DRAINAGE OPTION 2 Dishwasher using drain hose joiner onto sink trap/waste tee
Screw Drain hose support to back wall
at correct height.
Supplied drain hose joiner to suit 19 mm waste tee
750-883 mm
If space is limited
for fixing, push
hose through drain
hose support
to required height. 2
3
1
38 mm
step 15
min. 500 mm 750 – 883 mm
min. radius 200 mm
IMPORTANT!
Ensure that drain hose is installed as close to the underside of the benchtop
as possible. This will ensure no waste re-enters the drain hose in the event
of poor flow or a blockage in the plumbing. Ensure the drain hose does not
extend into water retained in the trap; an air gap is required to prevent
waste water from siphoning back into the tub.
IMPORTANT!
Ensure that drain connection complys with local plumbing regulations.
min. 500 mm 750 – 883 mm
1
step 15
min. radius 200 mm
Ensure drain hose is routed straight to the joiner so that waste water does
not accumulate in the hose. Remove excess drain hose material if necessary. Do
not shorten the inlet hose.
12
!5CONNECT INLET HOSE TO COLD WATER
!6PLUG PRODUCT IN
min. 10mm
3/4″ BSP connector
Ensure the supplied rubber washer is fitted inside the coupling.
1
180o
No leaks!
Tighten coupling with spanner.
2
!7 TROUBLESHOOTING
Excessive water remaining above the filter plate, after the rinse cycle. (This
is displayed as an A3 fault. See user guide How to attend to a fault’) Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place. No water supply. (This is displayed as an A1 fault. See user guideHow to
attend to a fault’) Check water is connected and turned on.
The dishwasher is beeping continuously There is a fault. See section How to attend to a fault’ in the User guide for further information and instructions. No program indicator lights up when the drawer is opened Ensure power is connected and is switched on. If it is and still no indicator ligths up, see thePreference options’ section of the Quick start guide’. An option called Open drawer auto power-on’ may need to be turned on.
Water around water supply and drainage connections Check connections, existing
plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly
fitted.
If product is tipping Ensure the product is secured to the cabinetry.
If front panels are misaligned Check and relevel product. Unscrew the product
from the cabinetry. Adjust the feet to level the product, then re-secure to
the cabinetry. Check the cabinetry is square.
Drawer doesn’t close properly Ensure nothing is obstructing the drawer from
closing properly eg hoses or drawer latches.
If a problem occurs, consult the `Troubleshooting’ section of the User guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorised
Service Centre, or contact us through our website, listed below.
13
!8 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Check all parts are installed.
Ensure that all panels and parts thereof are secure and final electrical tests
have been conducted in accordance with local electrical regulations.
Ensure product is level, securely fastened to the cabinetry and opens and
closes freely. The drawers must be free to fully close with no resistance from
the cabinetry.
Ensure inlet hose to water supply has supplied rubber washer fitted, and that
it’s tightened a further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and
drain connection has been made.
The drain hose joiner must not support the weight of excess hose material.
Keep drain hose as fully extended as possible to prevent sagging. Any excess
length of drain hose should be kept on the dishwasher side of the highloop.
If connecting the drain hose to the sink trap, ensure the Highloop is a
minimum 150mm higher than the drain hose joiner.
Ensure any packaging or tape securing the racks or spray arms is removed from
the drawers.
Water softener models only: adjust the water softener setting from the default
setting to suit the water hardness of the area. See the Quick start guide and
section `Water softener’ in the User guide.
Turn on the power and water supplies, then open the drawers. You should hear a
beep and see a program indicator light up on the control panel.
Check the spray arms are in place, mounted correctly and free to rotate, by
physically rotating by hand.
Spray arm
Add three cups of water into the drawer. Press program lights up. Close the drawer and press Repeat for the other drawer.
until the indicator of the `Rinse’ to start the program.
After the Rinse program has finished, ensure the dishwasher has run and drained correctly.
Check the water supply has correctly shut off and drainage connection for leakage.
Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date
F I S H E R PAY K E L .C O M
Copyright © Fisher & Paykel Appliances 2019. All rights reserved. The product
specifications in this booklet apply to the specific products and models
described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. You should therefore
check with your Dealer to ensure this booklet correctly
describes the product currently available.
14
SINGLE DISHDRAWERTM DISHWASHER
DD60SDF models
INSTALLATION GUIDE NZ AU GB IE SG 591384C05.19
1SAFETY AND WARNINGS
! WARNING!
IMPORTANT SAFETY INSTRUCTIONS
Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.
Installation of this dishwasher requires basic mechanical and electrical
skills.
Be sure to leave these Instructions with the Customer. Installation must
comply with your local building and
electricity regulations. At the completion of the dishwasher installation, the
Installer must perform the Final Checklist. Remove all packaging materials
supplied with the
dishwasher. This dishwasher is manufactured for indoor use only. Ensure all
water connections are turned OFF. It is
the responsibility of the plumber and electrician to ensure that each
installation complies with all Codes
WARNING- Improper connection of the equipment-earthing conductor can result in
a risk of electric shock. Check with a qualified electrician or service
representative if you are in doubt as to whether the appliance is properly
earthed. Do not modify the power supply plug provided with the appliance–if it
will not fit the outlet, have a proper outlet installed by a qualified
electrician. Do not use an extension cord, adapter plug or multiple outlet
box.
Failure to follow this advice may result in electrical shock or death.
and Regulations. The dishwasher MUST be installed to allow for future
removal from the enclosure if service is required. The switched power outlet
must be outside
the dishwasher cavity, so that it is accessible after installation. Care
should be taken when the appliance is installed or removed to reduce the
likelihood of damage to the power supply cord and hoses. If the dishwasher is
to be relocated from one installation to another it must be kept upright to
avoid damage from water spillage. Make sure only new hoses are used for
connection (supplied with the dishwasher). Old hoses should not
be reused.
! WARNING!
Cut Hazard Take care–panel edges are sharp. Failure to use caution could
result in injury or cuts.
Failure to install the dishwasher correctly could invalidate any warranty or
liability claims.
If the product is installed in a motor vehicle, boat or similar mobile
facility, you must bring the vehicle, boat or mobile facility containing the
product to the service shop at your expense or pay the service technician’s
1
travel to the location of the product.
2PARTS SUPPLIED
Drain hose support (1)
Drain hose joiner (1)
Wire clip (1) (for securing Drain hose joiner)
Clamp (1) (for securing Drain hose joiner)
Side mounting bracket kit (A and B) (2) OPTIONAL
Top mounting brackets (2) OPTIONAL
Phillips 16 mm screws (7)
38 mm bottom fixing screws & metal washers (2)
Rubber washer for inlet hose (1) (comes already fitted)
Moisture protection tape (1) (to prevent moisture damage to cabinetry)
Cavity Bracket Kit (1) (supplied with Tall Height Models only)
DishdrawerTM installation overview This video provides an overview of what is
needed to install a DishDrawerTM. It is intended as an overview only of the
installation process and is not intended to be used as a guide on how to
install a DishDrawerTM yourself. https://vimeo.com/325297597
If the Drain hoses supplied are not long enough to reach your services, you
must use a Drain Hose Extension Kit P/N 525798 which will extend the drain
hose by 3.6 m. The kit is available from the nearest Fisher & Paykel
Authorised Service Centre or our local website listed at the end of this
document.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country,
go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.
2
3PRODUCT DIMENSIONS
C H
F
A
FRONT
I
G
PROFILE
B
D E
j
PLAN 3
PRODUCT DIMENSIONS A Overall height of product1 B Overall width of product C
Overall depth of product D Depth of chassis (to back of front drawer panel) E
Depth of drawer front panel F Height of drawer front panel G Height of
chassis1 H Height from top of drawer front panel to top of chassis I
Ventilation gap below drawer front panel J Maximum extension of drawer
1 includes 2mm high bracket slots 2 includes fitted cavity bracket
STANDARD HEIGHT
TALL HEIGHT
DD60SDF MM 410 599 573 553 20 398 410 2 8 547
DD60SDFT MM 4782 599 573 553 20 470 454 24 8 547
CABINETRY DIMENSIONS K Inside height of cavity L Inside width of cavity M Inside depth of cavity
Q
Bracket slots
PLAN
4CABINETRY DIMENSIONS
K R
STANDARD HEIGHT
TALL HEIGHT
DD60SDF MM
min. 412 600
min. 560
DD60SDFT MM 480 600
min. 560
PROFILE Minimum clearances from adjacent cabinetry
Cavity height options allow you to match dishwasher with your cabinetry or companion products
DD60SDF (Standard height models)
DD60SDFT
DD6(0TSaCll (hHe)iTgMht7models)
K
min. 412mm
Dishwasher
K
480mm
Dishwasher
Oven
min. 13 mm clearance from a corner cupboard
min. 2 mm clearance to adjacent cupboard door
4
COUNTERTOP
10 mm
Moisture protection tape must be applied.
5 CAVITY PREPARATION
These marks indicate formed bracket screw locations, if securing by drawer
removal.
If there is no side partition, you can construct timber bracing as something
to secure into.
WARNING!
Incorrect placement of the hole will result in damage to hoses.
Ø 57mm max. 450mm
Max 5mm Max distance between hole edge and rear inner face
Max 10mm Max distance between hole edge and shelf
5
Service Holes Can be located either side of dishwasher, close to the rear face
and the shelf, as illustrated.
If the hole is through wood, make sure its edges are smooth and rounded.
If the hole is through metal, ensure you fit the supplied Edge Protector to
prevent damage to the power cord.
min. 200 mm
Water Connection Recommended COLD (Maximum 60°C). 3/4″ BSP (GB20) to suit flat
washer.
Water Pressure Water softener models Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5
psi) Models without water softener Max. 1 MPa (145 psi) Min. 0.03 MPa (4.3
psi)
IMPORTANT!
The power outlet must be located in a cabinet adjacent to the dishwasher
cavity. 220-240 VAC min. 4.8 A
6 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE
LEFT HAND SIDE
Drain hose–2000mm Inlet hose–1650mm
Power cord (excl.plug)–2000mm
RIGHT HAND SIDE
Drain hoses–1800mm Inlet hose–1250 mm Power cord (excl.plug)–2000mm
6 TALL HEIGHT DESIGNER MODELS FOR 480 MM CAVITY ONLY–ATTACH CAVITY BRACKET
IMPORTANT!
The enclosed cavity bracket is fitted before installation in order to conceal
the gap at the top of the cavity left after installation.
1
Firmly push the bracket so that
the prongs engage with the top
2
tabs and it clicks into place.
IMPORTANT!
Ensure the prongs have not been driven down into the chassis as this will
damage the lid below.
Ensure the top trim seal is facing forward after attaching the bracket.
Ensure the cavity panel bracket is positioned so that the “F” arrow is pointing towards the front of the chassis.
6
NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR
CABINETRY…
7 RECOMMENDED METHOD (A)–SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY
ONLY)
8-AATTACH SIDE MOUNTING BRACKETS
Clip all four side mounting
brackets into their slots using a
B
flat-bladed screwdriver. Ensure they’re securely fitted before
A
sliding product into cavity.
B A
9-APULL THROUGH HOSES & PUSH INTO THE CAVITY
A B
A
The mounting slots are in pairs, one on each side diagonally across the
product. A bracket must match A slot and B bracket must match B slot.
When fitting brackets, ensure the ends are not pushed down into the chassis. 7
B
As you push product in, pull through hoses and cord, ensuring they don’t get
kinked or twisted.
IMPORTANT!
If product cannot be pushed in far enough, pull out again and rearrange hoses
and cord. Do not use excessive force, as doing so may squash the hoses and
lead to incorrect operation.
!0-ASECURE TO THE CABINETRY ON THE SIDES
1 Open the drawer halfway.
Using a flat bladed screwdriver, prise the grey rubber plug out of the trim
moulding.
2 Using a small Philips screwdriver, screw
through the trim moulding, securing the side mounting bracket to the
cabinetry.
Do not damage the rubber trimseal.
3
Replace the grey rubber plug back
into the trim moulding and ensure
the trim seal is facing forward.
Repeat for all four brackets.
8
7 ALTERNATIVE METHOD (B)–SECURE BY DRAWER REMOVAL
8-BPULL THROUGH HOSES & PUSH INTO THE CAVITY
9-BREMOVE THE LOWER DRAWER
To prevent kinked hoses
Either sit the drawer down on the left
hand side (recommended) or rotate the
1
drawer clockwise, resting it on its side after removal.
3
As you push product in, pull through hoses and cord, ensuring they don’t get
kinked or twisted.
IMPORTANT!
If product cannot be pushed in far enough, pull out again and rearrange hoses
and cord. Do not use excessive force, as doing so may squash the hoses and
lead to incorrect operation.
9
2 3
100 mm
Sit the drawer down
4
Push drawer runners back in on either side.
Press the release tabs in on either side and push back to release drawer from runners. Lift drawer off runners.
Rotate the drawer clockwise (max. 90o) and rest on side.
4
Push drawer runners back in on either side.
!0-BSECURE TO THE CABINETRY ON THE SIDES
The product has three pairs of fixing points:
Ensure the sound insulation is repositioned correctly.
two pairs of formed brackets on either side
of the chassis (use 16 mm screws)
2
Before refitting the
drawer, ensure the hoses
are not twisted and the
latches at the rear of each drawer runner are
1
facing forward.
2
a pair of fixing
holes either side
on the bottom
1
(use 38 mm fixing
screws & washers)
!1-BREFIT THE DRAWER ONTO THE RUNNERS
Lift or rotate anti-clockwise the drawer back onto the drawer runners on either side.
4
100 mm
3
Pull the release tabs forward on both sides 100 mm. Ensure the tabs are fully
pulled forward and click into place.
Release tab
10
750-883 mm min. 500 mm
750 – 883 mm
!2 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
DRAINAGE OPTION 1 Dishwasher and Ø 38 mm Standpipe
DRAINAGE OPTION 2 Dishwasher using drain hose joiner onto sink trap/waste tee
Screw Drain hose support to back wall
at correct height.
If space is limited for fixing, push
hose through drain hose support
to required height. 2
max. 120 mm
Screw Drain hose support to back wall
at correct height.
If space is limited for fixing, push
hose through drain hose support
to required height. 2
750-883 mm
Supplied drain hose joiner to suit 19 mm waste tee
3
1
step 13 38 mm
1
step 13
min. 500 mm 750 – 883 mm
min. radius 200 mm
IMPORTANT!
Ensure that drain hose is installed as close to the underside of the benchtop
as possible. This will ensure no waste re-enters the drain hose in the event
of poor flow or a blockage in the plumbing.
Ensure the drain hose does not extend into water retained in the trap; an air
gap is required to prevent waste water from siphoning back into the tub.
IMPORTANT!
Ensure that drain connection complys with local plumbing regulations.
11
min. radius 200 mm
Ensure drain hose is routed straight to the joiner so that waste water does
not accumulate in the hose. Remove excess drain hose material if necessary. Do
not shorten the inlet hose.
!3CONNECT INLET HOSE TO COLD WATER
3/4″ BSP connector
Ensure the supplied
rubber washer is
fitted inside the
coupling.
1
min. 10mm
180o
2
Tighten coupling with spanner.
No leaks!
!4PLUG PRODUCT IN
12
!5 TROUBLESHOOTING
Excessive water remaining above the filter plate, after the rinse cycle. (This
is displayed as an A3 fault. See user guide How to attend to a fault’) Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain hose not routed correctly or spray arm not in place. No water supply. (This is displayed as an A1 fault. See user guideHow to
attend to a fault’) Check water is connected and turned on.
The dishwasher is beeping continuously There is a fault. See section How to attend to a fault’ in the User guide for further information and instructions. No program indicator lights up when the drawer is opened Ensure power is connected and is switched on. If it is and still no indicator ligths up, see thePreference options’ section of the Quick start guide’. An option called Open drawer auto power-on’ may need to be turned on.
Water around water supply and drainage connections Check connections, existing
plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly
fitted.
If product is tipping Ensure the product is secured to the cabinetry.
Drawer doesn’t close properly Ensure nothing is obstructing the drawer from
closing properly eg hoses or drawer latches.
If a problem occurs, consult the `Troubleshooting’ section of the User guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorised
Service Centre, or contact us through our website, listed below.
13
!6 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Check all parts are installed.
Ensure that all panels and parts thereof are secure and final electrical tests
have been conducted in accordance with local electrical regulations.
Ensure product is level, securely fastened to the cabinetry and opens and
closes freely. The drawers must be free to fully close with no resistance from
the cabinetry.
Ensure inlet hose to water supply has supplied rubber washer fitted, and that
it’s tightened a further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and
drain connection has been made.
The drain hose joiner must not support the weight of excess hose material.
Keep drain hose as fully extended as possible to prevent sagging. Any excess
length of drain hose should be kept on the dishwasher side of the highloop.
If connecting the drain hose to the sink trap, ensure the Highloop is a
minimum 150 mm higher than the drain hose joiner.
Ensure any packaging or tape securing the racks or spray arms is removed from
the drawers.
Water softener models only: adjust the water softener setting from the default
setting to suit the water hardness of the area. See the Quick start guide and
section `Water softener’ in the User guide.
Turn on the power and water supplies, then open the drawer. You should hear a
beep and see a program indicator light up on the control panel.
Check the spray arms are in place, mounted correctly and free to rotate, by
physically rotating by hand.
Spray arm
Add three cups of water into the drawer. Press program lights up. Close the drawer and press
until the indicator of the `Rinse’ to start the program.
After the Rinse program has finished, ensure the dishwasher has run and drained correctly.
Check the water supply has correctly shut off and drainage connection for leakage.
Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date
F I S H E R PAY K E L .C O M
Copyright © Fisher & Paykel Appliances 2019. All rights reserved. The product
specifications in this booklet apply to the specific products and models
described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. You should therefore
check with your Dealer to ensure this booklet correctly
describes the product currently available.
14
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>