franklin 30129X Folding Soccer Goal Instructions
- June 17, 2024
- FRANKLIN
Table of Contents
FOLDING SOCCER GOAL
SIZE: 6ft High x 12ft Wide
(1.83m x 3.65m)
BEFORE ASSEMBLY
Work on a smooth, flat surface.
Lay out all components so they are in easy reach.
Read assembly instructions completely to familiarize yourself with the
components before you begin assembly.
This goal is designed to provide many hours of enjoyment if properly assembled
and used only for the purpose intended.
Adult supervision is recommended when the goal is used by children.
FRAME COMPONENTS
| 1 | L Shaped Bent Tube | 4pcs | |
|---|---|---|---|
| 2 | Straight Double | ||
| Flanged Tube | 2pcs | ||
| 3 | Folding Corner Piece, Left | 1pcs | |
| 4 | Folding Corner Piece, Right | 1pcs | |
| 5 | Straight Double | 4pc | |
| 6 | Long 6 Straight Double Flanged Tube | 2pc | |
| 7 | Ground Stakes | 6pcs | |
| 8 | Pin | 2pcs | |
| 9 | Screw (Pre-assembled) | 2pcs | |
| 10 | Bolt (Pre-assembled) | 2pcs | |
| 11 | | Net| 1pc
12| | Self-Stick Straps| 40pcs
FRAME ASSEMBLY
Assemble all lengths of tubing as shown in Figure 1. Be sure that each piece is inserted completely. The end of each tube inserts tightly and is secured when the press button of the tapered end pops through the adjoining perforated tube. (Refer to Figure 1A)
Assembly Instructions
- Assemble top front cross bar and back base bar by inserting tube marked (1) into the tube (2). Then insert tube (2)into tube (5). Lastly insert tube (5) into another tube marked ‘O} Do this once for the back base and again for the front cross bar.
- Insert the remaining 2 pieces of tube(5) into the bent ends of tube (1) on each side of the back base.
- Connect the folding joint part (4) to the end of tube(5) and attach folding joint (3) to the other part G) on the side base.
- Insert tube(6)into tubes (3) and (5) on both ends of the structure.
- Attach the top front crossbar (assembled in step 1) to the upward pointing tubes marked (6).
- To fold goal (refer to figure 1B) remove the lock pin on both sides before folding top backwards. Once folded, insdert lock pins (8) to secure.
The net has been designed with red tabs to identify the top corners and blue
tabs to identify the bottom front corners.
Follow the numbered sequence to attach the net.
Net Assembly Instructions
- Using 4 self-stick closure straps, 2 for each corner on the top bar, tie the top right and top left corners, identified by the two RED tabs.
- Using 4 self-stick closure straps, 2 for each corner on the lower front bar, tie the lower right and lower left corners identified by the two BLUE tabs.
- Stretch the net and using 4 self-stick closure straps tie 2 each to the back bottom corners.
- Fill in the top front section with 8 self-stick straps.
- Fill in the two side sections with 6 self-stick straps.
- Fill in the bottom back section with 8 self-stick straps.
NOTE: Adjust the self-stick straps by moving the straps left or right as necessary to prevent large gaps.
NOTE: Following goal assembly, 6 ground stakes will help secure the goal. Two are recommended placed over each side/base tubes, right side and left side near the front. Two are recommended placed over the back/base tubes.
Franklin Sports Inc.
Stoughton, MA 02072
Made in China
For replacement parts call:
1-781-341-5178 or
1-800-225-8649
OR visit www.franklinsports.com
References
- Official MLB Gear, Pickleball Products, and Sporting Goods Equipment | Franklin Sports | Franklin Sports
- Manual-Hub.com – Free PDF manuals!