KING-METER KM529 EBike Control Instruments Kits Controller Panel User Guide
- June 17, 2024
- KING-METER
Table of Contents
- KING-METER KM529 EBike Control Instruments Kits Controller Panel
- Product Information
- Product Usage Instructions
- About the User Manual
- Appearance and Size
- Function Summary
- Monitor Area
- Operation Cautions
- Installation Instruction
- Normal Operation
- General Setting
- Connection layout
- Barcode
- FAQ
- Quality assurance and warranty scope
- Version changes
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KING-METER KM529 EBike Control Instruments Kits Controller Panel
Product Information
Specifications
- Product Name: KING-METER
- Model Number: KM529
- Material: PC
- Temperature Range: -20°C to 60°C
- Display Dimensions: (unit: mm)
Function Summary
KM529 provides the following functions and indicators:
- Battery Indicator
- Speed Display (including real-time speed, average speed, and max speed)
- Trip Distance and Total Distance
- PAS Level Selection
- Headlight On/Off
- Error Code Indicator
- Various Parameters Setting (wheel size, speed-limited, backlight brightness, etc.)
Appearance and Size
KM529 products are made of PC. The shell material ensures normal usage and good mechanical performance within the temperature range of -20°C to 60°C.
Product Usage Instructions
Operation Cautions
- Be careful with safety use.
- Do not attempt to release the connector when the battery is powered on.
- Avoid hitting the product.
- Avoid wetting the product.
- If the display doesn’t work normally, take it for repair.
Installation Instruction
- Fix the display onto the handlebar.
- Adjust to an appropriate visual angle.
- Tighten all the connectors.
Normal Operation
Power On/Off
- To power on the display and the controller, press the button for 2 seconds.
- To turn off the power system of the e-bike, press the button for 2 seconds (display must be on).
- If the display is off, both the display and controller shut down.
- The leakage current of the display in shutdown state is less than 1A.
- The display will shut down automatically if the e-bike is not in use for 10 minutes.
Speed Display (Real-time speed/Average speed/Max speed)
- After starting up the display, the default show is real-time speed.
- Long press both buttons to change the indicated information in sequence:
- Real-time Speed (Km/h)
- Average Speed (Km/h)
- Max Speed (Km/h)
Distance Display (Trip Distance/Total Distance)
- After starting up the display, the default show is real-time speed.
- Press the button to change the indicated information in sequence:
- Trip Distance (km)
- Total Distance (km)
- Long press both buttons to reset the trip distance to zero.
Turn on/off Backlight
- Press the button for 2 seconds to turn on the backlight of the display (headlight will be on at the same time).
- Hold the button for 2 seconds again to turn off the backlight.
PAS Level Selection
- Press the button or button to change the output power of the motor.
- The power ranges from level 1 to level 5, with level 1 being the minimum power and level 5 being the maximum power.
- The default value is level 1.
FAQ
Q: How do I reset the trip distance?
A: Long press both buttons to reset the trip distance to zero.
Q: How long does it take for the display to shut down automatically?
A: The display will shut down itself automatically if the e-bike is not in use for 10 minutes.
About the User Manual
Dear users,
To ensure better performance of your e-bike, please read through the KM29
product introduction carefully before using. We will use the most concise
words to inform you of all the details （including the hardware installation,
setting and normal operation use of the display）when using our display.
Meanwhile, the introduction will also help you to solve the possible confusion
and malfunctions.
Appearance and Size
KM529 products are made of PC. Under the temperature of -20 to 60℃, the shell material can ensure normal usage and good mechanical performance. Real product and dimension figure (unit: mm)
Function Summary
KM529 provides a wide range of functions and indicators to fit for users’ needs. The indicated contents are as follow.
- Battery Indicator
- Speed Display (including real-time speed, average speed and max speed)
- Trip distance and total distance
- PAS Level Selection
- Headlight On/Off
- Error Code Indicator
- Various Parameters Setting, such as wheel size, speed-limited, backlight brightness and so on.
Monitor Area
Operation Cautions
Be care of the safety use. Don’t attempt to release the connector when battery is power on.
Installation Instruction
Fix the display onto the handlebar and adjust to an appropriate visual angle. Tighten all the connectors.
Normal Operation
Power On/Off
Press Button for 2 seconds then the display will power on, and the controller
will power on at the same time. With display on, Press Button for 2 seconds to
turn off power system of the e-bike. With the display off, the display and
controller shut down. The leakage current of display on shutdown state is less
than 1μA
When the e-bike is without using for 10 minutes, the display will shut down itself automatically.
Speed Display (Real-time speed/Average speed/ Max speed)
After starting up the display, default show is real-time speed.
Long press both and buttons for 2s to change the indicated information in
sequence as below: Real-time Speed (Km/h) → Average Speed (Km/h) → Max Speed
(Km/h).
Distance Display (Trip Distance/ Total Distance)
After starting up the display, default show is Real-time speed.
Press button to change the indicated information in sequence as below: Trip
Distance (km) →Total Distance (km). Long press the two buttons and , the trip
distance will be reset to zero.
Turn on/off Backlight
Press button for 2 seconds to turn on the backlight of the display, the
headlight will be on at the same time. Hold Button for 2 seconds again,
backlight is off.
PAS Level Selection
Press button or button to change the output power of the motor. The power
ranges from level 1 to level 5. Level 1 is the minimum power. Level 5 is the
maximum power. The default value is level 1.
Battery Indicator
The display shows the battery capacity in 5 levels. When the battery is in
high voltage, the word FULL will show on the top of screen. When the battery
is under-voltage, the letter E will be shown on the bottom of screen and the
LCD indictor will flash, please charge the battery.
Error Code Information
If there is something wrong with the electronic control system, the error code
will appear automatically. When error appears, please check the corresponding
part of e-bike or sent the display to be repaired.
Following is the detail information of error code：
Error
Code
|
Definition
| Solution
---|---|---
21| Current Abnormality| Inspect if motor phrases short-circuits
22| Throttle Abnormality| Inspect if throttle recover original state
23
|
Motor Abnormality
| Inspect if motor phrase is well-connected;
Inspect if lines are well-connected between motor phrases and controller.
24
|
Motor Hall Signal Abnormality
| Non-Hall Controller ： Inspect if motor phrase is well-connected;
Hall Controller：Inspect if motor hall is well-connected.
25| Brake Abnormality| Inspect if brakes original state before
display startup.
30
| Communication Abnormality| Inspect if lines are well-connected between display and controller.
General Setting
When the display power on, press both buttons for 2 seconds to enter the setting menu. When the display is on status of general setting, press the button for 2 seconds to quit setting menu.
Wheel Diameter Setting
Press button to select the correct value to match the wheel diameter.
Selectable values include: 16 inch、18inch、20 inch、22 inch、24 inch、26
inch、700C，28 inch。Default diameter is 26 inch.
Press button to confirm the value of wheel diameter and enter next setting at
the same time.
Speed-limit Setting
When the running real-time speed is faster than the value of limited- speed
you set, the controller will cut off the motor power to protect the rider’s
safety. Limited speed default setting value is 25Km/h. the values of Limit-
Speed range from 12Km/h to
40Km/h. Press to select the favorite value, Press to confirm. Then enter the
next setting.
Backlight Contrast setting
“bL” means backlight. Level 1 is low brightness. Level 2 is the middle
brightness. Level 3 is high brightness. The default level is
- Press button to modify the backlight brightness.
Press button to confirm.
Connection layout
Following is the standard connector of display to connect the controller.
Line sequence table
| Line sequence | Color | Function |
|---|---|---|
| 1 | Red（VCC） | Power + |
| 2 | Blue(K) | Switch |
| 3 | Black(GND) | Ground |
| 4 | Green(RX) | Received Data |
| 5 | Yellow(TX) | Transmitted Data |
Some wire use the water-proof connector, users are not able to see the inside color.
Barcode
The barcode is built up as follows:
- KM529 = Name
- 000001=Sequence No.
- 12=Year of Production
- 06=Week of Production
- 3=Battery Voltage (2 is 24V, 3 is 36V, 4 is 48V)
- 1= Delivery form（1 is sample, 2 is mass production）
- 01=Hardware version No.
- 801=Software version No.
FAQ
Q: Why the display is not able to start up?
A: Check the connector between display and controller.
Q: How to deal with the error code?
A: Fix it to the maintenance place immediately.
Quality assurance and warranty scope
Warranty
- In guarantee period, display itself appears any quality problems when it is used correctly， our company will be responsible for warranty.
- The warranty time is 24 months when display out of the factory.
Other items
The following items do not belong to our warranty scope.
- It can not be demolished.
- The damage is caused by wrong installation or operation.
- Shell is broken when display is out of the factory.
- Wire is broken.
- The fault or damage is caused by the force majeure (such as fire, earthquake, etc,) or natural disasters like lighting, etc.
- Beyond warranty period.
Version changes
This operating instruction is a general-purpose version. Some of the version for the display software will be different from the specification, which should depend on the actual use version.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>