KitchenAid KSSC42QM Built-in Refrigerator Owner’s Manual

June 17, 2024
KitchenAid

KitchenAid KSSC42QM Built-in Refrigerator

Product Information

Specifications

  • Model Numbers: KSSC36FM, KSSC36QM, KSSC42FM, KSSC42QM,
    • KSSC48FM, KSSC48QM, KSSO36FM, KSSO36QM, KSSO42FM, KSSO42QM,
    • KSSO48FM, KSSO48QM, KSSP36QM, KSSP42QM, KSSP48QM, KSSS36FM,
    • KSSS36QM, KSSS42FM, KSSS42QM, KSSS48FM, KSSS48QM, KSSV42FM
  • Electrical Requirements: 115-volt, 60-Hz, AC-only, 15- or 20-ampere
  • Cold Water Supply: Connect the ice maker to a cold water line with water pressure between 20 and 120 psi (138 – 827 kPa)

Overall Dimensions

Width A:

  • 36 in. (91 cm) models: 35 in. (89 cm)

  • 42 in. (106 cm) models: 41 in. (104 cm)

  • 48 in. (122 cm) models: 47 in. (119 cm)

  • When leveling legs are fully extended to 1-1/4 in. (32 mm) below rollers, add 1-1/8 in. (29 mm) to the height dimensions.

Water Supply Requirements

If water shutoff valve is located in base cabinet, access hole through side of cabinet must be within 1/2 (12.7 mm) of rear wall. Right side cabinet is recommended. If water shutoff valve is not in cabinets, water line can come through rear wall or floor in shaded area dimensioned above.

Anti-Tip Requirements

A Width:

  • 36 in. (91.4 cm) models: 351/4 in. (90.2 cm)
  • 42 in. (106.7 cm) models: 411/4 in. (105.4 cm)
  • 48 in. (121.9 cm) models: 471/4 in. (120.7 cm)

Door Swing Dimensions

  • 36 in. (91 cm) models: 141/2 in. (37 cm)
  • 42 in. (106 cm) models: 193/4 in. (50 cm)
  • 48 in. (122 cm) models: 263/4 in. (68 cm)

Product Usage Instructions

Electrical Connection

A 115-volt, 60-Hz, AC-only, 15- or 20-ampere, fused electrical supply is required for the product to function properly. It is recommended to use a time-delay fuse or circuit breaker. A separate circuit serving only this appliance should be provided.

Cold Water Supply Connection

Connect the ice maker to a cold water line with water pressure between 20 and 120 psi (138 – 827 kPa). If you are unsure about your water pressure, contact your utility company for assistance.

Cabinet Opening Dimensions

Refer to the provided chart for the specific cabinet opening dimensions based on the model of the product.

Installation Instructions

For complete installation details, please refer to the Installation Instructions packed with the product. These instructions provide step-by-step guidance for proper installation.

FAQ

  • Can I use this product with a 220-volt electrical supply?
    • No, this product is designed to work with a 115-volt, 60-Hz, AC-only electrical supply. Using a higher voltage may damage the product and void the warranty.
  • What should I do if I experience low water pressure?
    • If you are experiencing low water pressure, first check if there are any obstructions in the water line or filter. If the issue persists, contact your utility company to ensure that the water pressure meets the recommended range of 20 to 120 psi (138 – 827 kPa).
  • Can I connect the ice maker to a hot water line?
    • No, it is recommended to connect the ice maker to a cold water line. Using a hot water line may affect the performance and lifespan of the product.
  • How do I level the product?
    • To level the product, adjust the leveling legs located at the bottom of the appliance. Fully extend the legs until they are 1-1/4 in. (32 mm) below the rollers, and then add an additional 1-1/8 in. (29 mm) to the height dimensions.

PRODUCT MODEL NUMBERS

  • KSSC36FM
  • KSSC36QM
  • KSSC42FM
  • KSSC42QM
  • KSSC48FM
  • KSSC48QM
  • KSSO36FM
  • KSSO36QM
  • KSSO42FM
  • KSSO42QM
  • KSSO48FM
  • KSSO48QM
  • KSSP36QM
  • KSSP42QM
  • KSSP48QM
  • KSSS36FM
  • KSSS36QM
  • KSSS42FM
  • KSSS42QM
  • KSSS48FM
  • KSSS48QM
  • KSSV42FM

Electrical: A 115-volt, 60-Hz, AC-only, 15- or 20-ampere, fused, electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.
Cold Water Supply: Connect the ice maker to a cold water line with water pressure between 20 and 120 psi (138 – 827 kPa). If you have questions about your water pressure, call your utility company).

OVERALL DIMENSIONS

KitchenAid-KSSC42QM-Built-in-Refrigerator-
fig-1

Other model series dispensing, and non-dispensing, with different styling are available.

Model Width A (Trim edge to trim edge)

36 in. (91 cm)

42 in. (106 cm)

48 in. (122 cm)

| 361/4 in. (92 cm)

421/4  in. (107 cm)

481/4  in. (123 cm)

Model Width A

36 in. (91 cm)

42 in. (106 cm)

48 in. (122 cm)

| 35 in. (89 cm)

41 in. (104 cm)

47 in. (119 cm)

  • When leveling legs areCABINET OPENING DIMENSIONS fully extended to 1-1/4 in.(32 mm) below rollers, add 1-1/8 in. (29 mm) to the height dimensions.KitchenAid-KSSC42QM-Built-in-Refrigerator-fig-3
Model Width A (as shown above)

36 in. (91.4 cm)

42 in. (106.7 cm)

48 in. (121.9 cm)

| 351/4 in. (90.2 cm)

411/4  in. (105.4 cm)

471/4  in. (120.7 cm)

WATER SUPPLY REQUIREMENTS

If water shutoff valve is located in base cabinet, access hole through side of cabinet must be within 1/2″ (12.7 mm) of rear wall. Right side cabinet is recommended. If the water shutoff valve is not in the cabinets, water line can come through rear wall or floor in shaded area dimensioned above.

ANTI-TIP REQUIREMENTS

  • A. Center board 1/4 in. (6 mm) max. above refrigerator
  • B. Two, 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards
  • C. Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws
  • D. Compressor cover

The solid soffit must be within 1 in. (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1 in. (2.5 cm) or one is not available, prevent the refrigerator from tipping during use as shown. Board(s) must be long enough to fully cover the width of the compressor cover. Locate the board(s) so the bottom surface of the board(s) are 84 in. (213 cm) from the floor. Securely attach one or two 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) wood boards to wall studs behind the refrigerator. Use 6 -#8 x 3 in. (7.6 mm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1-1/2 in. (3.8 cm). The board(s) must overlap the compressor cover.

DOOR SWING DIMENSIONS

  • Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
  • Dimensions are for planning purposes only. For complete details, see the Installation Instructions packed with the product. Specifications are subject to change without notice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KitchenAid User Manuals

Related Manuals