KENWOOD KAC-9105D Class D Mono Power Amplifier Instruction Manual

June 17, 2024
KENWOOD

KENWOOD KAC-9105D Class D Mono Power Amplifier

Product Information

Specifications

  • Model: KAC-9105D
  • Amplifier Type: Class D Mono Power Amplifier

Product Usage Instructions

Safety Precautions
Before using the power amplifier, it is important to follow these safety precautions:

  • WARNING: Follow all instructions and warnings marked on the product.
  • CAUTION: Take necessary precautions to prevent electric shock and fire hazards.
  • NOTE: This note provides additional information or tips for using the product.

Cleaning the Unit
To clean the front panel of the power amplifier:

  1. Turn off the power.
  2. Wipe the panel with a dry silicon cloth or soft cloth.
  3. CAUTION: Do not use a hard cloth or cloth dampened by volatile solvents such as paint thinner or alcohol. They can scratch the surface of the panel and cause damage to the indicator letters.

Preventing Battery Drain
To prevent battery depletion, follow these steps:

  1. When using the unit in the ACC ON position without starting the engine, it can deplete the battery. Use it after starting the engine.

Protection Function
The power amplifier is equipped with a protection function to safeguard the unit and speakers from accidents or problems. The protection function is triggered in the following situations:

  • The power indicator goes off
  • Amplifier stops operating

Wiring and Speaker Selection
Proper wiring and speaker selection are important for optimal performance. Follow the guidelines below:

  • Refer to the wiring diagram in the instruction manual for proper connections.
  • Ensure correct speaker selection and combined impedance according to your setup.

Installation Procedure
Follow these steps to install the power amplifier:

  1. Remove the ignition key and disconnect the negative terminal of the battery to prevent short circuits.
  2. Set the unit according to the intended usage.
  3. Remove the dressing cover.
  4. Connect the input and output wires of the units.
  5. Connect the speaker wires.
  6. Connect the power wire, power control wire, and grounding wire in the specified order.
  7. Install the installation fittings in the unit.
  8. Attach the unit securely.
  9. Attach the dressing cover.
  10. Connect the negative terminal of the battery.

FAQ (Frequently Asked Questions)

  • Q: Where can I register my Kenwood product?
    A: You can register your Kenwood product online at www.Kenwoodusa.com.

  • Q: How do I clean the front panel of the power amplifier?
    A: Turn off the power and wipe the panel with a dry silicon cloth or soft cloth. Do not use a hard cloth or cloth dampened by volatile solvents.

  • Q: What should I do if the protection function is triggered?
    A: If the protection function is triggered, the power indicator will go off and the amplifier will stop operating. Check for any issues with wiring or speaker connections and resolve them accordingly.

  • Q: Can I place objects on top of the power amplifier?
    A: No, once installed, do not place any objects on top of the unit to prevent heat build-up and ensure proper dissipation of heat.

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier.

For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call your Kenwood dealer for information or service on the product.

  • Model KAC-9105D Serial number

US Residents Only

Register Online
Register your Kenwood product at www.Kenwoodusa.com.

Safety precautions

WARNING
To prevent injury or fire, take the following precautions:

  • Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.
  • When extending the ignition, battery, or ground wires, make sure to use automotive-grade wires or other wires with the range of 8 mm2 (AWG 8) or more to prevent wire deterioration and damage to the wire coating.
  • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.
  • If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.
  • Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.

CAUTION
To prevent damage to the machine, take the following precautions:

  • Be sure the unit is connected to a 12V DC power supply with a negative ground connection.
  • Do not open the top or bottom covers of the unit.
  • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
  • When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.
  • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

NOTE

  • If you experience problems during installation, consult your Kenwood dealer.
  • If the unit does not seem to be working right, consult your Kenwood dealer.

Cleaning the unit
If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.

CAUTION
Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.

To prevent battery rise
When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.

Protection function
The protection function is activated in the following situations:

  • This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur.
  • When the protection function is triggered, the power indicator goes off and the amplifier stops operating.
  • When a speaker wire may be short-circuited.
  • When a speaker output contacts the ground.
  • When the unit malfunctions a DC signal is sent to the speaker output.

Wiring

  • Take the battery wire for this unit directly from the battery. If it’s connected to the vehicle’s wiring harness, it can cause blown fuses etc.
  • If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wires.
  • Do not allow the wire to directly contact the edge of the iron plate by using Grommets.
  • Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative terminal. Do not turn the power on if the ground wire is not connected.
  • Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger.
  • For the power cord and ground, use a vehicle-type (fireproof ) power wring cord. (Use a power wiring cord with a range of 8 mm2 (AWG 8) or more.)
  • When more than one power amplifier is going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.

Speaker Selection

  • The rated input power of the speakers that are going to be connected should be greater than the maximum output power (in Watts) of the amplifier. Use of speakers having input power ratings that are less than the output power of the amplifier will cause smoke to be emitted as well as damage.
  • Use speakers that have an impedance of 1Ω or greater. When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.

Example

Installation

Accessories

Installation procedure
Since there are a large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection.

  1. Remove the ignition key and disconnect the negative terminal of the battery to prevent short circuits.
  2. Set the unit according to the intended usage.
  3. Remove the Dressing cover.
  4. Connect the input and output wires of the units.
  5. Connect the speaker wires.
  6. Connect the power wire, power control wire and grounding wire following this order.
  7. Install the installation fittings in the unit.
  8. Attach the unit.
  9. Attach the Dressing cover.
  10. Connect the negative terminal of the battery.

CAUTION

  • Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)
  • Do not install the unit under the carpet. Otherwise, heat build-up occurs and the unit may be damaged.
  • Install this unit in a location that allows heat to easily dissipate. Once installed, do not place any object on top of the unit.
  • The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.
  • This unit has a cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan and ducts of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.
  • When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.
  • Do not install near the dashboard, rear tray, or airbag safety parts.
  • The installation of the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.
  • After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.

Connection

WARNING

  • Particular attention must be given to making good electrical contact at the amplifier output and speaker terminals.
  • Poor or loose connections can cause sparking or burning at the terminals because of the very high power that the amplifier can deliver.

CAUTION

  • If the sound is not output normally, immediately turn the power off and check the connections.
  • Be sure to turn the power off before changing the setting of any switch.
  • If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.
  • Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits.
  • Connect the speaker wires to the appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.
  • After installation, check that the brake lamps, turn signal lamps and windshield wipers work properly.

WARNING
Remove the ignition key and disconnect the negative terminal of the battery to prevent short circuits.

Power wire and Speaker wire connection

RCA cable or Speaker level input connection

RCA cable connections

Speaker-level input connections

NOTE
Do not connect cables and lead to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage.

Cable colour of the connector

Description

  1. Fuse (30 A x 3)
    NOTE
    If you can’t find the specified capacity fuse at your store etc., consult your Kenwood dealer.

  2. Battery terminal (BATT.)

  3. Ground terminal (GND)

  4. Power control terminal (P.CON)
    Controls the unit ON/OFF.
    NOTE
    Controls the unit power. Be sure to connect it with all the systems.

  5. Speaker output terminals
    As this unit accepts speakers with a minimum impedance of 1 ohm, connect speakers with 1- ohm or higher impedance to these terminals.

  6. BASS BOOST LEVEL control
    Sets the low-frequency level to be compensated.

  7. LPF (Low-Pass Filter) FREQUENCY control
    This control adjusts the frequency band output from this unit.

  8. INPUT SENSITIVITY control
    Set this control according to the pre-output level of the center unit connected with this unit.
    NOTE
    For the pre-output level, refer to the in the instruction manual of the centre unit.

  9. ISF (infrasonic filter) switch
    Ultralow frequencies that cannot be reproduced even by a subwoofer speaker do not become sound but become unnecessary oscillations, which affect the sound by causing distortion, etc. Setting this switch to “15 Hz” or “25 Hz” cuts the frequencies below the respective frequency. This improves the reproduction performance of the speakers by eliminating unnecessary oscillations which will not become sound.

  10. PHASE switch
    When this switch is set to “180°” (Reverse) the speaker output phase is reversed.

  11. LINE IN terminal

  12. LINE OUT terminal
    The signal that’s input from the line input terminal is output.

  13. SP LEVEL INPUT terminal

    • The genuine accessory car stereo shall have a maximum power output of no more than 40 W.
    • The power is turned on and off as the unit detects the input signal (SIGNAL SENSING TURN-ON). Therefore it is not necessary to connect the power control wire.
  14. Power indicator
    When the power is turned on, the Power indicator lights.

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling the service, first, check the following table for possible problems.

PROBLEM

| POSSIBLE CAUSE|

SOLUTION

---|---|---
No sound.

(No sound from one side.)

(Blown fuse.)

| •       Input (or output) cables are disconnected.

•       Protection circuit may be activated.

•       Volume is too high.

•       The speaker cord is shorted.

| •       Connect the input (or output) cables.

•       Check connections by referring to

.

•       Replace the fuse and use a lower volume.

•       After checking the speaker cord and fixing the cause of the short, replace the fuse.

The output level is too small (or too large).| • The input sensitivity adjusting control is not set to the correct position.| • Adjust the control correctly referring to .
The sound quality is bad.

(The sound is distorted.)

| •       The speaker’s wire is connected with the wrong +/- polarity.

•       A speaker wire is pinched by a screw in the car body.

•       The switches may be set improperly.

| •       Connect them properly checking the V/s of the terminals and wires well.

•       Connect the speaker wire again so that it is not pinched by anything.

•       Set switches properly by referring to .

Specifications

Specifications are subject to change without notice.

Audio Section

  • Max Power Output …………………………………………………………1800 W
  • Rated Power Output (+B = 14.4V)
    • (4 Ω) (20 Hz – 200 Hz, ≤ 1.0 % THD) …………………500 W × 1
    • (2 Ω) (100 Hz, ≤ 1.0 % THD) …………………………………900 W × 1
    • (1 Ω) ………………………………………………………………….. ≥ 900 W × 1
  • Speaker impedance …………………………………………………….1 Ω – 8 Ω
  • Frequency Response (+0, –3 dB) ………………..10 Hz – 200 Hz
  • Sensitivity (rated output)
    • MAX. …………………………………….. 0.2 V
    • MIN. ……………………………………… 5.0 V
  • Signal to Noise Ratio ……………………………………………………….. 100 dB
  • Input Impedance …………………………………………………………………10 kΩ
  • Low Pass Filter Frequency (-24 dB/oct.) ……50 Hz–200 Hz (variable)
  • Infrasonic Filter Frequency (-18 dB/oct.) …………15 Hz / 25 Hz
  • Bass Boost Control (40 Hz) ………………… 0 – +18 dB (variable)

General

  • Operating Voltage …………………… 14.4 V (11 – 16 V allowable)
  • Current Consumption …………………………………………………………57 A
  • Dimensions (W × H × D) ………………………350 × 59 × 238 mm 13-3/4 × 2-5/16 × 9-3/8 inch
  • Weight ……………………………………………………………….3.3 kg (7.2 lbs)

CEA-2006

  • RMS Watts per channel @ 4 ohms, ≤1% THD+N ………………………………………………………………500 W × 1
  • Signal to Noise Ratio (Reference: 1Watt into 4 ohms) ………………………………………………………………..75 dBA

Declaration of Conformity

Declaration of Conformity concerning the EMC Directive 2004/108/EC

  • Manufacturer:
    Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan

  • EU Representative’s:
    Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications if it is not installed and used under the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Information on Disposal of Old Electrical and Electronic Equipment (applicable for EU countries that have adopted separate waste collection systems)
Products with the symbol (crossed-out wheeled bin) cannot be disposed of as household waste. Old electrical and electronic equipment should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details on locating a recycling facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.

This Product is not installed by the manufacturer of a vehicle on the production line, nor by the professional importer of a vehicle into an EU Member State.

Dear Customer,
Thank you for purchasing this Kenwood product. As mentioned in the pages of this book, our warranty is only valid in the countries listed. If your country is not listed please contact your retailer for information on warranty procedure, or write to:

KENWOOD Corporation

Information Center
1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, Japan Customer 226-8525.

UK & Ireland

Dear User of Kenwood Products:
Thank you for having chosen this Kenwood product (the “Product”). If it becomes defective under normal operating conditions, it will be repaired or replaced free of charge in conformity with the terms of this Warranty Card. If the Product was purchased in any EEC Member State and you experience a problem, please leave the Product to any official Kenwood importer, Authorized Dealer, Authorized Service Centre or retailer of Kenwood products in the EEC, together with the purchase receipt or other adequate proof of the date of purchase. If it was purchased outside the EEC, the Product must be taken to the retailer from whom it was purchased.

If the Product was purchased in the EEC and you wish to know the location of your nearest Authorized Dealer in the EEC, please contact the following for information.

KENWOOD ELECTRONICS UK LTD.

Please keep this Warranty Card as you will need it should a claim be necessary. The Product is guaranteed for one year from the date of original purchase from any retailer of Kenwood products. The guarantee covers both materials and workmanship and the repair shall be carried out free of charge. We reserve the right to replace the Product if it cannot be repaired economically.

Packaging, installation costs and any other costs or risks indirectly related to the actual repair, are not included in the warranty services and will be charged.

Conditions

  • Any claim under this warranty must be accompanied by this Warranty Card, and in addition:

    • Your full name and address
    • The receipt or other document showing the date of purchase from a retailer established in Europe.
    • The full name and address of the retailer from whom the Product was purchased
    • The Serial Number and Model Name of the Product.
      If this information cannot be provided, or if the Product has been modified or altered in any way since the date of purchase, Kenwood Corporation reserves the right to refuse to repair the Product under the terms of this Warranty.
  • The Product has been manufactured so that it complies with all national or local standards and satety requirements applicable in the country of first sale by the manutacturer in Europe. Modifications necessary for use elsewhere are not covered by this Warranty, and no liability for repair will be accepted in respect of any work done in this connection or any damage to the Product arising from such work If the Product is used in a European country where it is subject to other standards and requirements than those applicable in the country of first sale by the manutacturer in Europe, then any warranty services will be subject to the condition that the user bears the cost of adapting the Product to the applicable standards and requirements. In addition, if the Product is different in type from those marketed by the official importer in the country where it is offered for warranty repair, and the appropriate spare parts are unavailable in this country or the warranty service cannot be provided in this country for another legitimate reason, then the cost of shipping the Product for repair to and from the country of original purchase shall be borne by the user.

  • This Warranty does not cover

    • alterations of the Product, and normal maintenance and adjustments, including periodic check-ups mentioned in the Manual used with the Product;
    • damage to the Product caused by inadequate or improper repairs carried out by any person or entity that is not authorized by the manufacturer to perform warranty services on its behalf;
    • damage to the Product caused by negligence, accidents, modifications, defective installation or packaging, or misuse. and use of inappropriate spare parts;
    • damage to the Product caused by fire, immersion in water, lightning, earthquake, inadequate ventilation, Acts of God, incorrect application of main voltage howsoever arising, or any other cause beyond the control of Kenwood;
    • loudspeakers damaged by application of power levels beyond the rated specification, and damages caused for whatever reason to record, tapes, cassette tapes, videotapes, compact disks, or any other goods which are not the product itself;
    • consumable or wearing items requiring replacement as part of normal service, including (but not limited to) phono- cartridges, stylus, and drive belts. tape heads, racks, dry cells, rechargeable batteries and final tubes:
    • the Product from which any or all of the serial numbers have been removed, modified or defaced;

This Warranty is available to any person who has legally obtained the Product. Subject as mentioned above, the Product will be repaired or replaced free of charge. These rights in no way interfere with or otherwise affect the rights of the user of the Product under the applicable legal provisions.

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

WARRANTY

KENWOOD USA CORPORATION
This warranty will be honoured only in the U.S.A.

KENWOOD LIMITED WARRANTY FOR CAR STEREO COMPONENTS

HOW LONG IS THE WARRANTY
Kenwood U.S.A. Corporation (“Kenwood”) warrants this product for one (1) year from the date of original purchase.

WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material and workmanship in Kenwood car stereo components. The following are not covered by the warranty:

  1. Any product which is not distributed in the U.S.A. by Kenwood or which is not purchased in the U.S.A. from an authorized Kenwood car stereo dealer or an automobile dealer, unless the product is purchased through the U.S.A Military Exchange Service.
  2. Any product on which the serial number has been defaced, modified or removed.
  3. Damage, deterioration or malfunction resulting from:
    • Any shipment of the product (claims must be presented to the carrier).
    • Installation or removal of the product.
    • Accidents, acts of nature, misuse, abuse, neglect, unauthorized product modification or failure to follow instructions supplied with the product.
    • Repair or attempted repair by anyone not authorized by Kenwood.
    • Any other cause which does not relate to a product defect.

WHO IS PROTECTED
This warranty is enforceable only by the original purchaser.

WHAT WE WILL PAY FOR
We will pay for all labour and material expenses for covered items. Payment of shipping charges is discussed in the next section of this warranty.

HOW TO OBTAIN WARRANTY SERVICE

If your KENWOOD product ever needs service:

  1. Take or ship it to any KENWOOD Authorized Service Center in the U.S.A. along with & a complete description of the problem. (if you are uncertain as to whether a Service Center is authorized, please call 1-800-KENWOOD for the nearest Service Center. 1-800-536-9663).
  2. Although you must pay any shipping charges if it is necessary to ship the product for warranty service, we will pay the return shipping charges if the repairs are covered by the warranty within the United States.
  3. Whenever your units are taken or sent for warranty service, you must include a copy of the original dated sales receipt as proof of warranty coverage.

LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.

EXCLUSION OF DAMAGES
KENWOOD’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR OPTION. KENWOOD SHALL NOT BE LIABLE FOR:

  1. INSTALLATION OR REMOVAL CHARGES, DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN KENWOOD CAR STEREO COMPONENTS, DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT; OR
  2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If a problem develops during or after the Limited Warranty Period, or if you have any questions regarding the operation of the product, you should contact your KENWOOD Authorized Dealer or Authorized Service Center. If the problem or your question is not handled to your satisfaction, please contact our Customer Relations Department at the address listed below:

KENWOOD USA CORPORATION

  • P.O Box 22745, 2201 East Dominguez Street, Long Beach, CA 90801-5745
  • Tel: 310-639-5300

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

MILITARY
Units purchased through the U.S.A. military exchange service overseas may be serviced under warranty in the continental U.S.A., subject to the following conditions.

  1. The original warranty is in effect.
  2. Proof of purchase is provided to the servicer.

WARRANTY FOR MILITARY MARKET
Kenwood Corporation is proud of the quality and workmanship of its audio equipment. This unit has been properly designed, tested and inspected before it was shipped to you. If properly installed and operated in accordance with the instructions furnished, it should give you an optimum reliable performance.

WARRANTY PERIOD
This product is warranted for (1) year from the date of the original purchase.

SCOPE OF WARRANTY
Except as specified below, this warranty covers all defects in materials and workmanship of the Kenwood brand products.

During the warranty period, any authorized Kenwood Service Center in the military market listed in the back of this warranty card will provide you free-of-charge both parts and labor required to correct any defect in materials or workmanship.

The following are not covered by this warranty.

  1. Voltage conversions.
  2. Periodic check-ups which do not disclose any defect covered by the warranty.
  3. Cabinets, grilles, other exterior finishes, belts, tape heads, and other non-durable parts and accessories.
  4. Units on which the serial number has been effaced, modified or removed.
  5. Installation and/or removal charges.
  6. Damaged magnetic tapes.
  7. House call charges for any repairs.
  8. Shipping or delivery charges to or from an authorized Kenwood Service Center.
  9. This warranty will not cover any failure that is due to any of the following conditions under the visual inspection of the authorized Kenwood Service Center:
    • Improper maintenance or repair, including the installation of parts or accessories that do not conform to the quality and specifications of the original parts.
    • Misuse, abuse, neglect, unauthorized product modification or failure to follow instructions contained in the Owner’s Manual.
    • Accidental or intentional damages.
    • Repairs or attempted repairs by an unauthorized agency. (All repairs must be performed at an authorized Kenwood Service Center.)
    • Damages or deteriorations caused during shipment (Claims must be presented to the carrier).
    • Damages or deteriorations resulting from removal and/or replacement.

PURCHASER’S RESPONSIBILITIES
As the purchase of a new Kenwood brand product, you are requested to do the following to obtain Kenwood warranty service.

  1. Retain your sales slip or other evidence of purchase to prove your eligibility for requesting Kenwood warranty service.
  2. Make your unit available to an authorized Kenwood Service Center in the military market for inspection and approved warranty service, or ship your unit in its original carton box or equivalent, fully insured and shipping charges prepaid, to the authorized Kenwood Service Center.

LIMITATION OF IMPLIED WARRANTIES
Any implied warranties, including warranties of merchantability and fitness for a particular purpose, shall be limited in duration to the length of this warranty.

EXCLUSION OF CERTAIN DAMAGES
KENWOOD’s liability for any defective product is limited to the repair or replacement of the said product, at our potion, and shall not include damages of any kind, whether incidental, consequential or otherwise, expect to the extent prohibited by applicable law.

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

JAPAN:

Yokota
Kenwood Rep,: c/o Yokota BX, JAAX AAFES-PAC, APO San Francisco 96328

U.S.A.:

Hawaii
Kenwood Factory Service 99-994 Iwaena St., Aiea, Hawaii 96701

In The Continental U.S.A.

  • For Nearest Authorized Service Center;
  • Tel: 1-800-536-9663

Kenwood Service U.S.A.

  • Kenwood Factory Service; P.O. Box 22745, 2201 East Dominguez Street, Long Beach, California 90801-5745
  • Tel: 310-639-5300

EUROPE:
Please inquire at the military resale outlets where you bought your Kenwood products or KENWOOD ELECTRONICS DEUTSCHLAND GMBH:

  • Rembrücker-Str. 15, 63150 Heusenstamm, Germany
  • Tel.: 49-06104-69010

KENWOOD ELECTRONICS CANADA INC.

CANADA

KENWOOD WARRANTY
KENWOOD ELECTRONICS CANADA INC. (hereinafter called “KENWOOD”), gives the following written warranty to the original customer of each new Kenwood product distributed in Canada by KENWOOD and purchased from a dealer authorized by KENWOOD.

KENWOOD warrants that each new Kenwood product, under normal use, is free from any defects, subject to the terms and conditions set forth below. If a defect should occur within the warranty period, repairs will be made free of charge for parts and labour when such defects are determined by KENWOOD or its authorized service centres to be attributable to faulty materials or workmanship at the time of manufacture. Please contact KENWOOD to confirm if a dealer or service centre is authorized by KENWOOD.

WARRANTY PERIOD
This Kenwood product is warranted for parts and labour for a period of one (1) year from the date of original purchase, lease or rental, except for products that are used in a professional or commercial application, which are warranted for a period of ninety (90) days for parts and labour and are subject to the terms and conditions of the warranty.

WARRANTY PERIOD
This Kenwood product is warranted for parts and labour for a period of one (1) year from the date of original purchase, lease or rental, except for products that are used in a professional or commercial application, which are warranted for a period of ninety (90) days for parts and labour and are subject to the terms and conditions of the warranty.

WARRANTY EXCLUSIONS
This warranty excludes:

  • Products purchased in a foreign country or purchased in Canada and taken to a foreign country.
  • Products purchased from a dealer not authorized by KENWOOD.
  • Products with the serial number defaced, altered or missing.
  • Periodic check-ups which do not disclose any defects covered by this warranty.
  • Defects resulting from disaster, accident, abuse, misuse, lightning, power surges, neglect or lack of periodic maintenance, unauthorized modification or failure to follow instructions in the owner’s manual.
  • Defects or damage as a result of repairs performed by a person or party not authorized by KENWOOD.
  • Defects resulting from the use of parts or devices that do not conform to KENWOOD specifications.
  • Damage or deterioration occurs to any exterior finishes, cosmetic parts, tape heads, adaptors, antennas, cables, tapes, discs or faults or damage caused by defective or leaking batteries.
  • Defects or damage occurring during shipping (claims should be presented to the shipping company).
  • Product voltage and /or line frequency conversions.
  • Product installation or removal charges.

TO OBTAIN WARRANTY SERVICE
Should your Kenwood product require warranty service, deliver it to any authorized KENWOOD service centre and present the original copy of your bill of sale and this warranty card as proof of warranty, or send your product fully insured and freight prepaid to the nearest authorized KENWOOD service centre. To avoid possible shipping damage, make sure the product is properly packed. Include a copy of your original bill of sale and this warranty card as proof of warranty along with your name, home and /or work telephone number(s), a complete return address and a detailed description of the faults). Products repaired within warranty will be returned freight prepaid to destinations within Canada. The customer is responsible for all freight and related costs for the return of product(s) to destinations outside Canada.

ENTIRE WARRANTY
This warranty constitutes the entire written warranty given by KENWOOD. No person, party, dealer service centre or their agents or employees are authorized to extend or enlarge this warranty on behalf of KENWOOD by any written or verbal statement or advertisement or promotion, including any extended warranty program or plan that may be offered by the dealer or service centre, unless approved in writing by KENWOOD.

DISCLAIMER
KENWOOD disclaims any responsibility for loss of time or use of the product or any other indirect, incidental or consequential damage to other products or goods, inconvenience or commercial loss.

NOTICE TO CONSUMER
The provisions contained in this written warranty are not intended to limit, modify, take away, disclaim or exclude any warranties or rights you may have that are outlined in any applicable provincial or federal laws or legislation.

IMPORTANT
This warranty card by itself is not considered by KENWOOD as valid proof of purchase. When applying for warranty repairs, you must present the original copy of your bill of sale and this warranty card as proof of warranty, so we recommend that they be kept in a safe place, should they be required in the future.

KENWOOD ELECTRONICS CANADA INC.

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

AUSTRALIA

KENWOOD ELECTRONICS AUSTRALIA PTY. LTD.
The warranty will only be honoured in the country in which the unit was originally purchased.

EXPRESS WARRANTY STATEMENT FOR CAR STEREO AND PERSONAL AUDIO COMPONENTS
KENWOOD ELECTRONICS AUSTRALIA PTY. LTD. is proud of the quality and workmanship of its audio equipment. This unit has been properly designed, tested and inspected before it was shipped to you. If properly installed and operated in accordance with instructions furnished, it should give optimum reliable performance.

SCOPE OF EXPRESS WARRANTY
Each of the KENWOOD brand products is expressly warranted under normal installation and use against defects in material and workmanship. During the express warranty period, KENWOOD ELECTRONICS AUSTRALIA PTY. LTD. will provide to any KENWOOD Authorised Service Centre in Australia free of charge both parts and labour necessary to correct any defect in material or workmanship. However, the exclusions noted under the heading “CONDITIONS OF THE EXPRESS WARRANTY” are not covered by this express warranty.

EXPRESS WARRANTY PERIOD
The KENWOOD brand car stereo and personal audio components are expressly warranted for ONE YEAR from the date of the original purchase.

CONDITIONS OF THE EXPRESS WARRANTY
When requesting service under the KENWOOD express warranty record, together with a valid purchase docket must be presented to an authorised KENWOOD Service Centre with your equipment.

The following are not covered by this express warranty:

  1. Voltage conversions.
  2. Cabinets, grilles, other exterior finishes, belts, tape heads, and other non-durable parts and accessories.
  3. Any fault caused by faulty installation, water damage, the vehicle (including its electrical system) or connection to an incorrect power supply.
  4. Periodic check-ups which do not disclose any defects covered by the warranty.
  5. Units on which the serial number has been defaced, modified or removed.
  6. Damage or deterioration:
    • Resulting from the installation and/or removal of the product.
    • Resulting from accident, misuse, abuse, neglect, unauthorised product modification or failure to follow instructions contained in the Owner’s Manual.
    • Resulting from repair by anyone not authorised by KENWOOD.
    • Resulting from the installation of parts or accessories that do not conform to the quality or specifications of the original parts or accessories.
    • Occurring during shipment (claims must be presented to shipper).
  7. Damaged magnetic tapes.
  8. Installation and removal charges are not covered.
  9. This express warranty excludes shipping or delivery charges to or from an authorised KENWOOD Service Centre.
  10. The benefits conferred by this express warranty are in addition to all other rights and remedies in respect of the product that the consumer has under the Trade Practices Act and/or other State or Territory Laws.

EXCLUSION OF CERTAIN DAMAGES
KENWOOD’s liability for any defective product is limited to the repair or replacement of said product at our option, and shall not include damages of any kind, whether incidental, consequential or otherwise.

PROCEDURE WHEN REQUESTING SERVICE UNDER THE WARRANTY

  1. Make your equipment available, with this warranty record and purchase docket attached, to the dealer from whom you made the purchase or the nearest authorised KENWOOD Service Centre, or ship your equipment in its original packaging, or equivalent, fully insured and shipping charges prepaid, to the authorised KENWOOD Service Centre.
  2. Attach a detailed description of the problem encountered, including details of any interconnections made to associated equipment.
  3. Make sure you recover this card, your purchase docket and repair docket when accepting the equipment back after repair.

IMPORTANT NOTICE

  1. Proper maintenance and use are important to the performance level of all KENWOOD brand products. Therefore, you should read your instruction manual.
  2. Retain your purchase docket together with this warranty record in a safe place, and present them both to prove your eligibility for warranty work.
  3. We recommend that you keep all the original packaging as it provides the best protection you can have for the transportation of your equipment in the future.
  4. The location of the nearest KENWOOD Service Centre will be sent upon request.
  5. This warranty is in addition to and not in place of such rights that the owner may have at law.

KENWOOD ELECTRONICS AUSTRALIA PTY. LTD.

  • 16 GIFFNOCK AVENUE, CENTRE COURT ESTATE, NORTH RYDE, N.S.W. 2113, AUSTRALIA
  • TEL. (02) 8879-2222
  • FAX. (02) 8879-2233

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

MALAYSIA

KENWOOD ELECTRONICS (MALAYSIA) SDN. BHD.
The warranty will only be honoured in the country in which the unit was originally purchased.

EXPRESS WARRANTY STATEMENT FOR CAR STEREO AND PERSONAL AUDIO COMPONENTS
KENWOOD ELECTRONICS (MALAYSIA) SDN. BHD. is proud of the quality and workmanship of its audio equipment. This unit has been properly designed, tested and inspected before it was shipped to you. If properly installed and operated under instructions furnished, it should give optimum reliable performance.

SCOPE OF EXPRESS WARRANTY
Each of the KENWOOD brand products is expressly warranted under normal installation and use against defects in material and workmanship. During the express warranty period, KENWOOD ELECTRONICS (MALAYSIA) SDN. BHD. will provide to any KENWOOD Authorised Service Centre in Malaysia free of charge both parts and labour necessary to correct any defect in material or workmanship. However, the exclusions noted under the heading “CONDITIONS OF THE EXPRESS WARRANTY” are not covered by this express warranty.

EXPRESS WARRANTY PERIOD
The KENWOOD brand car stereo and personal audio components are expressly warranted for ONE YEAR from the date of the original purchase.

CONDITIONS OF THE EXPRESS WARRANTY
When requesting service under the KENWOOD express warranty record, together with a valid purchase docket must be presented to an authorised KENWOOD Service Centre with your equipment.

The following are not covered by this express warranty:

  1. Voltage conversions.
  2. Cabinets, grilles, other exterior finishes, belts, tape heads, and other non-durable parts and accessories.
  3. Any fault caused by faulty installation, water damage, the vehicle (including its electrical system) or connection to an incorrect power supply.
  4. Periodic check-ups which do not disclose any defects covered by the warranty.
  5. Units on which the serial number has been defaced, modified or removed.
  6. Damage or deterioration:
    • Resulting from the installation and/or removal of the product.
    • Resulting from accident, misuse, abuse, neglect, unauthorised product modification or failure to follow instructions contained in the Owner’s Manual.
    • Resulting from repair by anyone not authorised by KENWOOD.
    • Resulting from the installation of parts or accessories that do not conform to the quality or specifications of the original parts or accessories.
    • Occurring during shipment (claims must be presented to shipper).
  7. Damaged magnetic tapes.
  8. Installation and removal charges are not covered.
  9. This express warranty excludes shipping or delivery charges to or from an authorised KENWOOD Service Centre.
  10. The benefits conferred by this express warranty are in addition to all other rights and remedies in respect of the product that the consumer has under the Sales of Goods Act 1957 (Revised 1989).

EXCLUSION OF CERTAIN DAMAGES
KENWOOD’s liability for any defective product is limited to the repair or replacement of said product at our option, and shall not include damages of any kind, whether incidental, consequential or otherwise.

PROCEDURE WHEN REQUESTING SERVICE UNDER THE WARRANTY

  1. Make your equipment available, with this warranty record and purchase docket attached, to the dealer from whom you made the purchase or the nearest authorised KENWOOD Service Centre, or ship your equipment in its original packaging, or equivalent, fully insured and shipping charges prepaid, to the authorised KENWOOD Service Centre.
  2. Attach a detailed description of the problem encountered, including details of any interconnections made to associated equipment.
  3. Make sure you recover this card, your purchase docket and repair docket when accepting the equipment back after repair.

IMPORTANT NOTICE

  1. Proper maintenance and use are important to the performance level of all KENWOOD brand products. Therefore, you should read your instruction manual.
  2. Retain your purchase docket together with this warranty record in a safe place, and present them both to prove your eligibility for warranty work.
  3. We recommend that you keep all the original packaging as it provides the best protection you can have for the transportation of your equipment in the future.
  4. The location of the nearest KENWOOD Service Centre will be sent upon request.
  5. This warranty is in addition to and not in place of such rights that the owner may have at law.

KENWOOD ELECTRONICS (MALAYSIA) SDN. BHD.

  • 4.01 LEVEL 4, WISMA ACADEMY, LOT 4A JALAN19/1, 46300 PETALING JAYA, SELANGOR, MALAYSIA

  • TEL. (03) 7958-8333
  • FAX. (03) 7954-1233

ATTENTION
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft or damage.

www.Kenwoodusa.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals