GIGABYTE GA-H81M-DS2 Plus Motherboard User Manual

GIGABYTE GA-H81M-DS2 Plus Motherboard

Product Information

Specifications

• CPU: Supports LGA1150 socket for 4th Generation Intel® Core™ processors
• Chipset: Intel® H81 Express Chipset
• Memory: 2 x DDR3 DIMM sockets supporting up to 16 GB of system memory
• Graphics: Integrated Graphics Processor – Intel® HD Graphics support
• Audio: Realtek® ALC887 codec for High Definition Audio
• LAN: Realtek® GbE LAN chip (10/100/1000 Mbit)
• Expansion Slots: 1 x PCI Express x16 slot, 2 x PCI Express x1 slots
• Storage Interface: 2 x SATA 6Gb/s connectors, 2 x SATA 3Gb/s connectors
• USB: 2 x USB 3.0/2.0 ports, 6 x USB 2.0/1.1 ports

Product Usage Instructions

Chapter 1: Hardware Installation

Installation Precautions:

• Prior to installation, carefully read the user’s manual and follow the provided procedures.
• Avoid electrostatic discharge (ESD) to prevent damage to delicate electronic circuits and components.

Chapter 2: Product Specifications

CPU:

• The motherboard supports LGA1150 socket for 4th Generation Intel® Core™ processors.

Chipset:

• The motherboard features Intel® H81 Express Chipset.

Memory:

• The motherboard has 2 x DDR3 DIMM sockets supporting up to 16 GB of system memory.
• Note that when more than 4 GB of physical memory is installed on a Windows 32-bit operating system, the displayed memory size will be less than the installed physical memory size.

Onboard Graphics:

• The motherboard supports integrated Graphics Processor – Intel® HD Graphics.

Audio:

• The motherboard is equipped with Realtek® ALC887 codec for High Definition Audio.
• To configure 7.1-channel audio, you need to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

LAN:

• The motherboard features a Realtek® GbE LAN chip with 10/100/1000 Mbit capability.

Expansion Slots:

• The motherboard has 1 x PCI Express x16 slot and 2 x PCI Express x1 slots, all conforming to PCI Express 2.0 standard.

Storage Interface:

• The motherboard provides 2 x SATA 6Gb/s connectors (SATA3 0/1) and 2 x SATA 3Gb/s connectors (SATA2 2/3) for storage devices.

USB:

• The motherboard has 2 x USB 3.0/2.0 ports and 6 x USB 2.0/1.1 ports for connecting USB devices.

FAQ

• Q: What is the maximum amount of system memory supported by the motherboard?
  A: The motherboard supports up to 16 GB of system memory.

• Q: Can I use a Windows 32-bit operating system with more than 4 GB of physical memory?
  A: Yes, but please note that the displayed memory size will be less than the installed physical memory size.

• Q: How do I configure 7.1-channel audio on the motherboard?
  A: To configure 7.1-channel audio, you need to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

• Q: What type of LAN chip does the motherboard have?
  A: The motherboa rd features a Realtek® GbE LAN chip with 10/100/1000 Mbit capability.

Copyright
© 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE’s prior written permission.

• In order to assist in the use of this product, carefully read the User’s Manual.
• For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: “REV: X.X.” For example, “REV: 1.0” means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:

GA-H81M-DS2 Plus Motherboard Layout

Box Contents

• GA-H81M-DS2 Plus motherboard
• Motherboard driver disk
• User’s Manual
• Two SATA cables
• I/O Shield

The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

GA-H81M-DS2 Plus Motherboard Block Diagram

For detailed product information/limitation(s), refer to “1-2 Product Specifications.”

Chapter 1 Hardware Installation

Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user’s manual and follow these procedures:

• Prior to installation, make sure the chassis is suitable for the motherboard.
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
• Do not place the computer system on an uneven surface.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

Product Specifications

• GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
• Please visit the Support & Downloads\Utility page on GIGABYTE’s website to check the supported operating system(s) for the software listed in the “Unique Features” and “Bundled Software” columns.

Installing the CPU
Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU. (Go to GIGABYTE’s website for the latest CPU support list.)
• Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.
• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
• Apply an even and thin layer of thermal grease on the surface of the CPU.
• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur.
• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc.

Installing the CPU
Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically during the process of re-engaging the lever after you insert the CPU.

Installing the Memory
Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
  (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.)

• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

Dual Channel Memory Configuration
This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.
The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:

• Channel A: DDR3_1
• Channel B: DDR3_2

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.

Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:

• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

Back Panel Connectors

• a PS/2 Keyboard and PS/2 Mouse Port
  Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

• b D-Sub Port
  The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920×1200 (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports D-Sub connection to this port.

• c USB 3.0/2.0 Port
  The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification.
  Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

• d RJ-45 LAN Port
  The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

• e USB 2.0/1.1 Port
  The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB
  keyboard/mouse, USB printer, USB flash drive and etc.

  • When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
  • When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

• f Line In Jack (Blue)
  The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

• g Line Out Jack (Green)
  The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

• h Mic In Jack (Pink)
  The Mic in jack. Microphones must be connected to this jack.

To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

Internal Connectors

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.

1/2) ATX_12V/ATX (2×2 12V Power Connector and 2×12 Main Power Connector)

• With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation.
• The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

3/4) CPU_FAN/SYS_FAN (Fan Headers)
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.
When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer

• Always turn off your computer and unplug the power cord before replacing the battery.
• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.
• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model.
• When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side should face up).
• Used batteries must be handled in accordance with local environmental regulations.

SATA3 0/1 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device.

SATA2 2/3 (SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device.

To enable hot-plugging for the SATA ports, refer to Chapter 2, “BIOS Setup,” “Peripherals\SATA Configuration,” for more information.

F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PLED/PWR_LED (Power LED):
Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

• PW (Power Switch):
  Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, “BIOS Setup,” “Power Management,” for more information).

• SPEAK (Speaker):
  Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.

• HD (Hard Drive Activity LED):
  Connects to the hard drive activity LED on the chassis front panel. The RES (Reset Switch): LED is on when the hard drive is reading or writing data. Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

• CI (Chassis Intrusion Header):
  Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

• NC: No connection.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) and AC’97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

• The front panel audio header supports HD audio by default.
• Audio signals will be present on both of the front and back panel audio connections simultaneously.
• Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

F_USB1/F_USB2 (USB 2.0/1.1 Headers)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer

• Do not plug the IEEE 1394 bracket (2×5-pin) cable into the USB header.
• Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.

CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds

• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. After system restart, go to BIOS Setup to load factory defaults (select
• Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, “BIOS Setup,” for BIOS configurations).

Chapter 2 BIOS Setup

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS.
To access the BIOS Setup program, press the key during the POST when the power is turned on. To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.

• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS.
• Because BIOS flashing is potentially risky, if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.
• It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system’s failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values. (Refer to the “Load Optimized Defaults” section in this chapter or introductions of the battery/clear CMOS jumper in Chapter 1 for how to clear the CMOS values.)

Startup Screen
The following startup Logo screen will appear when the computer boots.(Sample BIOS Version: F1a)

On the main menu of the BIOS Setup program, press arrow keys to move among the items and press to accept or enter a sub-menu. Or you can use your mouse to select the item you want.

• When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.
• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

M.I.T.

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency, total memory size, CPU temperature, Vcore, and memory voltage.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings may result in system’s failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)

M.I.T. Current Status
This screen provides information on CPU/memory frequencies/parameters.

Advanced Frequency Settings

• Processor Graphics Clock
  Allows you to set the onboard graphics clock. The adjustable range is from 400 MHz to 4000 MHz. (Default: Auto)

• CPU Clock Ratio
  Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being installed.

• CPU Frequency
  Displays the current operating CPU frequency.

Advanced CPU Core Settings

• CPU Clock Ratio, CPU Frequency
  The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu.

• K OC (Note)
  Allows for increased performance by using certain CPUs. (Default: Auto)

(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel® CPUs’ unique features, please visit Intel’s website.

• CPU PLL Selection
  Allows you to set the CPU PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• Filter PLL Level
  Allows you to set the Filter PLL. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• Uncore Ratio
  Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.

• Uncore Frequency
  Displays the current CPU Uncore frequency.

• Intel(R) Turbo Boost Technology (Note)
  Allows you to determine whether to enable the Intel CPU Turbo Boost technology. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• Turbo Ratio (Note)
  Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios according to the CPU specifications. (Default: Auto)

• Turbo Power Limit (Watts)
  Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the specified power limit, the CPU will automatically reduce the core frequency in order to reduce the power. Auto sets the power limit according to the CPU specifications. (Default: Auto)

• Core Current Limit (Amps)
  Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specified current limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the power limit according to the CPU specifications. (Default: Auto)

• No. of CPU Cores Enabled (Note)
  Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU cores may vary by CPU). Auto lets the BIOS automatically configure this setting. (Default: Auto)

• Hyper-Threading Technology (Note)
  Allows you to determine whether to enable multi-threading technology when using an Intel® CPU that supports this function. This feature only works for operating systems that support multi-processor mode. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• CPU Enhanced Halt (C1E) (Note)
  Enables or disables Intel® CPU Enhanced Halt (C1E) function, a CPU power- saving function in system halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• C3 State Support (Note)
  Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• C6/C7 State Support (Note)
  Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption. The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• CPU Thermal Monitor (Note)
  Enables or disables Intel® Thermal Monitor function, a CPU overheating protection function. When enabled, the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS automatically configure this setting. (Default: Auto)

(Note) This item is present only when you install a CPU that supports this feature. For more information about Intel® CPUs’ unique features, please visit Intel’s website.

• CPU EIST Function (Note 1)
  Enables or disables Enhanced Intel® Speed Step Technology (EIST). Depending on CPU loading, Intel
  EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease average power consumption and heat production. Auto lets the BIOS automatically configure this setting.

• (Default: Auto)

• Extreme Memory Profile (X.M.P.) (Note 2)

• Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when enabled.

  • Disabled Disables this function. (Default)
  • Profile1 Uses Profile 1 settings.
  • Profile2 (Note 2) Uses Profile 2 settings.

• System Memory Multiplier
  Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD data. (Default: Auto)

• Memory Frequency (MHz)
  The first memory frequency value is the normal operating frequency of the memory being used; the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings.

Advanced Memory Settings

Extreme Memory Profile (X.M.P.) (Note 2), System Memory Multiplier, Memory

• Frequency(MHz)
  The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu.

• Memory Boot Mode (Note 2)
  Provides memory detection and training methods.
  Auto Lets the BIOS automatically configure this setting. (Default)
  Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory boot.
  Disable Fast Boot Detect and train memory at every single boot.

• Memory Initialization Mode
  Allows you to configure memory timing profile for different frequency memory. Options are: Auto (default), Normal Speed, High Speed, Extreme Speed.

• Memory Enhancement Settings
  Provides three different memory performance enhancement settings: Normal (basic performance), Enhanced Stability, and Enhanced Performance. (Default: Normal)

• Memory Timing Mode
  Manual and Advanced Manual allows the Channel Interleaving, Rank Interleaving, and memory timing settings below to be configurable. Options are: Auto (default), Manual, Advanced Manual.

• Profile DDR Voltage
  When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Disabled, the value is displayed according to your memory specification. When Extreme Memory Profile (X.M.P.) is set to Profile1 or Profile2, the value is displayed according to the SPD data on the XMP memory.

• Channel Interleaving
  Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)

(Note 1) This item is present only when you install a CPU that supports this feature. For more information about Intel® CPUs’ unique features, please visit Intel’s website.
(Note 2) This item is present only when you install a CPU and a memory module that support this feature.

Rank Interleaving
Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting. (Default: Auto)

Channel A/B Memory Sub Timings
This sub-menu provides memory timing settings for each channel of memory. This sub-menu provides memory timing settings for each channel of memory. The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual. Note: Your system may become unstable or fail to boot after you make changes on the memory timings. If this occurs, please reset the board to default values by loading optimized defaults or clearing the CMOS values.

Advanced Voltage Settings
This sub-menu allows you to set CPU and memory voltages.

PC Health Status

• Reset Case Open Status

  • Disabled Keeps or clears the record of previous chassis intrusion status. (Default)
  • Enabled Clears the record of previous chassis intrusion status and the Case Open field will
    show “No” at next boot.

• Case Open
  Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header. If the system chassis cover is removed, this field will show “Yes”, otherwise it will show “No”. To clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to the CMOS, and then restart your system.

• CPU Vcore/CPU VRIN/DRAM Voltage/+3.3V/+5V/+12V/CPU VAXG
  Displays the current system voltages.

• CPU/System Temperature
  Displays current CPU/system temperature.

• CPU/System Fan Speed
  Displays current CPU/system fan speeds.

• CPU/System Temperature Warning
  Sets the warning threshold for CPU/system temperature. When temperature exceeds the threshold, BIOS will emit warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF.

• CPU/System Fan Fail Warning
  Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or fan connection when this occurs. (Default: Disabled)

• CPU Fan Speed Control
  Allows you to determine whether to enable the fan speed control function and adjust the fan speed.

  • Normal Allows the fan to run at different speeds according to the CPU temperature. You can adjust the fan speed with System Information Viewer based on your system requirements. (Default)
  • Silent Allows the fan to run at slow speeds.
  • Manual Allows you to control the fan speed under the Fan Speed Percentage item.
  • Full Speed Allows the fan to run at full speeds.

• Fan Speed Percentage
  Allows you to control the fan speed. This item is configurable only when CPU Fan Speed Control is set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.

• System Fan Speed Control
  Allows you to determine whether to enable the fan speed control function and adjust the fan speed.

  • Normal Allows the fan to run at different speeds according to the system temperature. You can adjust the fan speed with System Information Viewer based on your system requirements. (Default)
  • Silent Allows the fan to run at slow speeds.
  • Manual Allows you to control the fan speed under the Fan Speed Percentage item.
  • Full Speed Allows the fan to run at full speeds.

• Fan Speed Percentage
  Allows you to control the fan speed. This item is configurable only when System Fan Speed Control is
  set to Manual. Options are: 0.75 PWM value /oC ~ 2.50 PWM value /oC.

• Miscellaneous Settings

• PCIe Slot Configuration
  Allows you to set the operation mode of the PCI Express slots to Gen 1 or Gen

2. Actual operation mode is subject to the hardware specification of each slot. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• 3DMark01 Boost
  Allows you to determine whether to enhance some legacy benchmark performance. (Default: Disabled)

System Information

This section provides information on your motherboard model and BIOS version. You can also select the default language used by the BIOS and manually set the system time.

• System Language
  Selects the default language used by the BIOS.

• System Date
  Sets the system date. The date format is week (read-only), month, date, and year. Use to switch between the Month, Date, and Year fields and use the or key to set the desired value.

• System Time
  Sets the system time. The time format is hour, minute, and second. For example, 1 p.m. is 13:0:0. Use to switch between the Hour, Minute, and Second fields and use the or key to set the desired value.

• Access Level
  Displays the current access level depending on the type of password protection used. (If no password is set, the default will display as Administrator.) The Administrator level allows you to make changes to all BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all.

BIOS Features

• Boot Option Priorities
  Specifies the overall boot order from the available devices. For example, you can set hard drive as the first priority (Boot Option #1) and DVD ROM drive as the second priority (Boot Option #2). The list only displays the device with the highest priority for a specific type. For example, only hard drive defined as the first priority on the Hard Drive BBS Priorities submenu will be presented here.
  Removable storage devices that support GPT format will be prefixed with “UEFI:” string on the boot device list. To boot from an operating system that supports GPT partitioning, select the device prefixed with “UEFI:” string.
  Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64-bit, select the optical drive that contains the Windows 7 64-bit installation disk and is prefixed with “UEFI:” string.

• Hard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities
  Specifies the boot order for a specific device type, such as hard drives, optical drives, floppy disk drives, and devices that support Boot from LAN function, etc. Press on this item to enter the submenu that presents the devices of the same type that are connected. This item is present only if at least one device for this type is installed.

• Bootup NumLock State
  Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST. (Default: Enabled)

• Security Option
  Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup.
  After configuring this item, set the password(s) under the Administrator Password/User Password item.
  Setup A password is only required for entering the BIOS Setup program.
  System A password is required for booting the system and for entering the BIOS Setup program.
  (Default)

• Full Screen LOGO Show
  Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the
  GIGABYTE Logo when the system starts up. (Default: Enabled)

• Fast Boot
  Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup speed. (Default: Disabled)

• VGA Support
  Allows you to select which type of operating system to boot.
  Auto Enables legacy option ROM only.
  EFI Driver Enables EFI option ROM. (Default)
  This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.

• USB Support
  Disabled All USB devices are disabled before the OS boot process completes.
  Full Initial All USB devices are functional in the operating system and during the POST.
  Partial Initial Part of the USB devices are disabled before the OS boot process completes. (Default)
  This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot is set to Ultra Fast.

• PS2 Devices Support
  Disabled All PS/2 devices are disabled before the OS boot process completes.
  Enabled All PS/2 devices are functional in the operating system and during the POST. (Default)
  This item is configurable only when Fast Boot is set to Enabled. This function is disabled when Fast Boot is set to Ultra Fast.

• NetWork Stack Driver Support
  Disabled Disables booting from the network. (Default)
  Enabled Enables booting from the network.
  This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.

• Next Boot After AC Power Loss
  Normal Boot Enables normal bootup upon the return of the AC power. (Default)
  Fast Boot Keeps the Fast Boot settings upon the return of the AC power.
  This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.

• Limit CPUID Maximum (Note)
  Allows you to determine whether to limit CPUID maximum value. Set this item to Disabled for Windows XP operating system; set this item to Enabled for legacy operating system such as Windows NT4.0. (Default: Disabled)

• Execute Disable Bit (Note)
  Enables or disables Intel® Execute Disable Bit function. This function may enhance protection for the computer, reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system. (Default: Enabled)

• Intel Virtualization Technology (Note)
  Enables or disables Intel® Virtualization Technology. Virtualization enhanced by Intel® Virtualization
  Technology will allow a platform to run multiple operating systems and applications in independent partitions.
  With virtualization, one computer system can function as multiple virtual systems. (Default: Enabled)

• Intel TXT(LT) Support (Note)
  Enables or disables Intel® Trusted Execution Technology (Intel® TXT). Intel® Trusted Execution Technology provides a hardware-based security foundation. (Default: Disabled)

• VT-d (Note)
  Enables or disables Intel® Virtualization Technology for Directed I/O. (Default: Enabled)
  (Note) This item is present only when you install a CPU that supports this feature. For more information about
  Intel® CPUs’ unique features, please visit Intel’s website.

• Windows 8 Features
  Allows you to select the operating system to be installed. (Default: Other OS)

• CSM Support
  Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process.

  • Always Enables UEFI CSM. (Default)
  • Never Disables UEFI CSM and supports UEFI BIOS boot process only.
    This item is configurable only when Windows 8 Features is set to Windows 8 or Windows 8 WHQL.

• Boot Mode Selection
  Allows you to select which type of operating system to boot.

  • UEFI and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM. (Default)
  • Legacy Only Allows booting from operating systems that only support legacy Option ROM.
  • UEFI Only Allows booting from operating systems that only support UEFI Option ROM.
  • This item is configurable only when CSM Support is set to Always.

• LAN PXE Boot Option ROM
  Allows you to select whether to enable the legacy option ROM for the LAN controller. (Default: Disabled)
  This item is configurable only when CSM Support is set to Always.

• Storage Boot Option Control
  Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller.

  • Disabled Disables option ROM.
  • Legacy only Enables legacy option ROM only. (Default)
  • UEFI only Enables UEFI option ROM only.
  • Legacy First Enables legacy option ROM first.
  • UEFI First Enables UEFI option ROM first.
  • This item is configurable only when CSM Support is set to Always.

• Other PCI Device ROM Priority
  Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN, storage device, and graphics controllers.

  • Legacy OpROM Enables legacy option ROM only.
  • UEFI OpROM Enables UEFI option ROM only. (Default)
    This item is configurable only when CSM Support is set to Always.

• Network stack
  Disables or enables booting from the network to install a GPT format OS, such as installing the OS from the Windows Deployment Services server. (Default: Disabled)

• Ipv4 PXE Support
  Enables or disables IPv4 PXE Support. This item is configurable only when Network stack is enabled.

• Ipv6 PXE Support
  Enables or disables IPv6 PXE Support. This item is configurable only when Network stack is enabled.

• Administrator Password
  Allows you to configure an administrator password. Press on this item, type the password, and then press . You will be requested to confirm the password. Type the password again and press . You must enter the administrator password (or user password) at system startup and when entering
  BIOS Setup. Differing from the user password, the administrator password allows you to make changes to all BIOS settings.

• User Password
  Allows you to configure a user password. Press on this item, type the password, and then press . You will be requested to confirm the password. Type the password again and press .
  You must enter the administrator password (or user password) at system startup and when entering BIOS
  Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.
  To cancel the password, press on the password item and when requested for the password, enter
  the correct one first. When prompted for a new password, press without entering any password.
  Press again when prompted to confirm.

NOTE: Before setting the User Password, be sure to set the Administrator Password first.

Peripherals

• Initial Display Output
  Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard graphics.

  • IGFX Sets the onboard graphics as the first display.
  • PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the first display. (Default)

• XHCI Mode
  Allows you to determine the operating mode for the xHCI controller in OS.

  • Smart Auto This mode is available only when the BIOS supports the xHCI controller in the pre-boot environment. This mode is similar to Auto, but it adds the capability to route the ports to xHCI or EHCI according to setting used in previous boots (for non-G3 boot) in the pre-boot environment. This allows the use of USB 3.0 devices prior to OS boot. xHCI controller enabling and rerouting should follow the steps in Auto, when previous boot routs ports to EHCI. Note: This is the recommended mode when BIOS has xHCI preboot support. (Default)

  • Auto BIOS routes the sharable ports to EHCI controller. Then it uses ACPI protocols to
    provide an option to enable the xHCI controller and reroute the sharable ports. Note:
    This is the recommended mode when BIOS does NOT have xHCI pre-boot support.

  • Enabled All shared ports are eventually routed to the xHCI controller during the BIOS boot process.
    If BIOS does not have pre-boot support for the xHCI controller, it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller. Note: OS has to provide support for the xHCI controller in this mode. If the OS does not provide support, all sharable ports won’t work.

• Disabled The USB 3.0 ports are routed to the EHCI controller and the xHCI controller is turned off. All USB 3.0 devices function as High Speed devices regardless of xHCI software support/availability.

• Manual Allows you to determine whether to rout the USB 3.0 ports to the xHCI or EHCI controller before booting to OS, and also provides you with options to manually rout each USB 3.0/2.0 port to xHCI or EHCI.

• Audio Controller
  Enables or disables the onboard audio function. (Default: Auto)
  If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled.

• Intel Processor Graphics
  Enables or disables the onboard graphics function. (Default: Enabled)

• Intel Processor Graphics Memory Allocation
  Allows you to set the onboard graphics memory size. Options are: 32M~1024M. (Default: 64M)

• DVMT Total Memory Size
  Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX. (Default: MAX)

• Legacy USB Support
  Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)

• XHCI Hand-off
  Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off support. (Default: Enabled)

• EHCI Hand-off
  Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off support. (Default: Disabled)

• USB Storage Devices
  Displays a list of connected USB mass storage devices. This item appears only when a USB storage device is installed.

• OnBoard LAN Controller
  Enables or disables the onboard LAN function. (Default: Enabled)
  If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled.

• SATA Configuration

• Integrated SATA Controller
  Enables or disables the integrated SATA controllers. (Default: Enabled)

• SATA Mode Selection
  Allows you to decide whether to configure the SATA controller integrated in the Chipset to AHCI mode.

  • IDE Configures the SATA controller to IDE mode.
  • AHCI Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced
  • Serial ATA features such as Native Command Queuing and hot plug. (Default)

• Serial ATA Port 0/1/2/3

• Port 0/1/2/3
  Enables or disables each SATA port. (Default: Enabled)

• Hot plug
  Enables or disable the hot plug capability for each SATA port. (Default: Disabled)

• External SATA
  Enables or disables support for external SATA devices. (Default: Disabled)

• Realtek PCIe GBE Family Controller
  This sub-menu provides information on LAN configuration

Power Management

• Power Loading
  Enables or disables dummy load. When the power supply is at low load, a self- protection will activate causing it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically configure this setting. (Default: Auto)

• Resume by Alarm
  Determines whether to power on the system at a desired time. (Default: Disabled)
  If enabled, set the date and time as following:

  • Wake up day : Turn on the system at a specific time on each day or on a specific day in a month.
  • Wake up hour/minute/second : Set the time at which the system will be powered on automatically.
  • Note: When using this function, avoid inadequate shutdown from the operating system or removal of the AC power, or the settings may not be effective.

• Soft-Off by PWR-BTTN
  Configures the way to turn off the computer in MS-DOS mode using the power button.

  • Instant-Off Press the power button and then the system will be turned off instantly. (Default)
  • Delay 4 Sec. Press and hold the power button for 4 seconds to turn off the system. If the power button is pressed for less than 4 seconds, the system will enter suspend mode.

• RC6(Render Standby)
  Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption. (Default: Disabled)

• AC BACK
  Determines the state of the system after the return of power from an AC power loss.

  • Memory The system returns to its last known awake state upon the return of the AC power.
  • Always On The system is turned on upon the return of the AC power.
  • Always Off The system stays off upon the return of the AC power. (Default)

• Power On By Keyboard
  Allows the system to be turned on by a PS/2 keyboard wake-up event.
  Note : To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

  • Disabled Disables this function. (Default)
  • Password Set a password with 1~5 characters to turn on the system.
  • Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
  • Any Key Press any key to turn on the system.

• Power On Password
  Set the password when Power On By Keyboard is set to Password.
  Press on this item and set a password with up to 5 characters and then press to accept.
  To turn on the system, enter the password and press .
  Note : To cancel the password, press on this item. When prompted for the password, press again without entering the password to clear the password settings.

• Power On By Mouse
  Allows the system to be turned on by a PS/2 mouse wake-up event.
  Note : To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

  • Disabled Disables this function. (Default)
  • Move Move the mouse to turn on the system.
  • Double Click Double click on left button on the mouse to turn on the system.

• ErP
  Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
  Note : When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,

• PME event wake up, power on by mouse, power on by keyboard, and wake on LAN.

Save & Exit

• Save & Exit Setup
  Press on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup program. Select No or press to return to the BIOS Setup Main Menu.

• Exit Without Saving
  Press on this item and select Yes. This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Select No or press to return to the BIOS Setup Main Menu.

• Load Optimized Defaults
  Press on this item and select Yes to load the optimal BIOS default settings. The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values.

• Boot Override
  Allows you to select a device to boot immediately. Press on the device you select and select Yes to confirm. Your system will restart automatically and boot from that device.

• Save Profiles
  This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and save as Setup Profile 1~ Setup Profile 8. Press to complete. Or you can select Select File in HDD/USB/FDD to save the profile to your storage device.

• Load Profiles
  If your system becomes unstable and you have loaded the BIOS default settings, you can use this function to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS settings. First select the profile you wish to load and then press to complete. You can select Select
  File in HDD/USB/FDD to input the profile previously created from your storage device or load the profile automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked properly (last known good record).

Chapter 3 Appendix

Drivers Installation

• Before installing the drivers, first install the operating system. (The following instructions use Windows 8.1 as the example operating system.)
• After installing the operating system, insert the motherboard driver disk into your optical drive. Click on the message “Tap to choose what happens with this disc” on the top-right corner of the screen and select “Run Run.exe.” (Or go to My Computer, double-click the optical drive and execute the Run.exe program.)

“Xpress Install” will automatically scan your system and then list all of the drivers that are recommended to install. You can click the Xpress Install button and “Xpress Install” will install all of the selected drivers. Or click the arrow icon to individually install the drivers you need.

Regulatory Statements

• Regulatory Notices
  This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose.
  Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE.

• Our Commitment to Preserving the Environment
  In addition to high-efficiency performance, all GIGABYTE motherboards fulfill European Union regulations for RoHS (Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment) and WEEE (Waste Electrical and Electronic Equipment) environmental directives, as well as most major worldwide safety requirements. To prevent releases of harmful substances into the environment and to maximize the use of our natural resources, GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your “end of life” product.

• Restriction of Hazardous Substances (RoHS) Directive Statement
  GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE and PBB). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.

• Waste Electrical & Electronic Equipment (WEEE) Directive Statement
  GIGABYTE will fulfill the national laws as interpreted from the 2002/96/EC WEEE (Waste Electrical and Electronic Equipment) directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric and electronic devices and their components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.

WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste equipment for recycling, please contact your local government office, your household waste disposal service or where you purchased the product for details of environmentally safe recycling.

• When your electrical or electronic equipment is no longer useful to you, “take it back” to your local or regional waste collection administration for recycling.
• If you need further assistance in recycling, reusing in your “end of life” product, you may contact us at the Customer Care number listed in your product’s user’s manual and we will be glad to help you with your effort. Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly. With your help, we can reduce the amount of natural resources needed to produce electrical and electronic equipment, minimize the use of landfills for the disposal of “end of life” products, and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly.

FCC Notice (U.S.A. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult a dealer or experienced TV/radio technician for help.

Canada, Industry Canada (IC) Notices / Canada, avis d’Industry Canada (IC)

• This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Contact Us

GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bao Chiang Road, Hsin-Tien Dist., New Taipei City 231,Taiwan TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : http://esupport.gigabyte.com WEB address (English): http://www.gigabyte.com
WEB address (Chinese): http://www.gigabyte.tw

You may go to the GIGABYTE website, select your language in the language list on the top right corner of the website.

GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to: http://esupport.gigabyte.com

References

• Manual-Hub.com - Free PDF manuals!
• GIGABYTE Global
• GIGABYTE 技嘉科技
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>