Honeywell 5115G Steel Security Safe Instruction Manual

Honeywell 5115G Steel Security Safe

Product Information

Specifications

• Models: 5101, 5101DOJ, 5102, 5103SL, 5110, 5111, 5115, 5101G, 5101GDOJ, 5102G, 5103GSL, 5110G, 5111G, 5115G
• Type: Steel Security Safe

Package Contents

• Steel Security Safe

Lock Overview

• LED Indicator Lights
• Digital Keypad
• Open/Close Knob
• Access Key Cover

Product Usage Instructions

Setup

Step 1. Open Safe with Override Key

1. Remove override key cover with a small screwdriver.
2. Insert the override key and turn left to unlock the safe.
3. Turn the knob to the right and open the safe door.

Step 2. Install Batteries

1. Remove the battery compartment cover on the inside door (A).
2. Insert 4 AA batteries (included), ensuring correct polarity (+ and -) as shown in the diagram.
3. Replace the battery cover.
4. Do not close the door before testing the digital lock.

Step 4. Program a New Passcode

1. With the door open, press the reset button (C) inside the door.
2. The yellow light will be on, enter a new passcode within 30 seconds.
3. Enter the new code (3 to 8 digits) followed by A or B.
4. The safe will beep, and the yellow light will turn off.

Note: The factory pre-set code will not work after a new passcode is programmed.

Operation

To Open the Safe

1. Enter the passcode followed by A or B to unlock and open the safe.
2. Turn the door entry knob to the right and open the door.

To Close the Safe

1. Close the door and hold it in the closed position.
2. Turn the door entry knob to the left to engage the lock bolts and lock the safe.

Secure Lockout Periods
If the wrong user code is entered into the keypad 3 consecutive times in a row, the keypad will automatically revert to lockout mode. You will not be able to open the safe using the digital keypad for 20 seconds. If three additional wrong user codes are entered, you will not be able to open the safe using the digital keypad for 5 minutes. During the lockout period, entry can be made using the override access key.

Override Access Key
If the passcode is unavailable or your keypad fails due to dead batteries or other malfunction, you can open the safe using the override access key.

Replacing Batteries

Note: The passcode might be reset to the original factory passcode (159) if batteries are removed or become too weak. Always test your passcode after replacing batteries to ensure it is still active. Refer to step 4 of the Setup section on page 2 to reprogram your passcode.

IMPORTANT: The starter batteries included with this product are for testing purposes only and should be immediately replaced with new alkaline or lithium batteries. Non-alkaline or rechargeable batteries are not recommended for use.

Weak or dead batteries should be replaced immediately, and all 4 batteries should be changed. To replace the batteries, please follow the instructions in the Setup section. Remember to always remove batteries from the safe if not using it for an extended period of time. If your batteries are completely dead and you cannot open the safe using the digital keypad, use the override access key to open the safe and access the battery compartment.

Frequently Asked Questions (FAQ)

• Q: Can I use rechargeable batteries in this safe?
  A: No, it is not recommended to use rechargeable batteries. Please use new alkaline or lithium batteries.

• Q: What should I do if I forget my passcode?
  A: If you forget your passcode, you can use the override access key to open the safe. Then, refer to step 4 of the Setup section on page 2 to reprogram your passcode.

PACKAGE CONTENTS

• 1 – Steel Security Safe
• 1 – Operation Manual
• 2 – Override Access Keys
• 4 – “AA” Batteries
• 1 – Mounting Kit w/ Bolts (Except 5103SL/5103GSL)
• 1 – Removable Shelf (Models 5103SL/5103GSL- 5110/5110G-5111/5111G only)

ATTENTION
DO NOT RETURN SAFE TO STORE!
For missing parts or difficulty operating your safe, please contact our Consumer Assistance Department by telephone.
Store will not accept returned products without prior authorization. You must first contact our consumer assistance department (See page 7 for contact information).

LOCK OVERVIEW

IMPORTANT – TEST DIGITAL LOCK BEFORE INSTALLING!!

SETUP

STEP 1. OPEN SAFE WITH OVERRIDE KEY

1. Remove override key cover with small screwdriver.
2. Insert override key and turn left to unlock safe.
3. Turn knob to right and open safe door.

STEP 2. INSTALL BATTERIES

1. Remove battery compartment (A) cover on inside door. Insert 4 “AA” batteries (included). Ensure the batteries are installed in the correct direction, with regard to polarity (+ and -) See diagram.
2. Replace the battery cover.
3. Do not close door before testing digital lock.

STEP 3. TEST DIGITAL LOCK

1. With door open, turn knob left to put locking door bolts (B) in lock position.

2. Remove override key and store in a secure place.
   NEVER STORE KEYS INSIDE SAFE!

3. Enter the preset pass code: “1”-“5”–“9”-“B” .

4. Turn knob to right within 5 seconds.

5. Lock bolts should recede into the unlocked position.

STEP 4. PROGRAM A NEW PASSCODE

1. With door open, press reset button (C) inside door.
2. Yellow light is on, enter new pass code in 30 seconds.
3. Enter new code (3 to 8 digits) followed by “A” or “B”.
4. Safe will beep and yellow light will turn off.
   NOTE: The factory pre-set code will not work after a new pass code is programmed.

OPERATION

TO OPEN THE SAFE

1. To unlock and open safe, enter the pass code followed by “A” or “B”.
2. Turn door entry knob to the right and open door.

TO CLOSE THE SAFE

1. Close the door and hold it in the closed position.
2. Turn door entry knob to left to engage the lock bolts and lock safe.

SECURE LOCKOUT PERIODS
If the wrong user code is entered into the keypad 3 consecutive times in a row, the keypad will automatically revert to the lockout mode and you will not be able to open the safe using the digital keypad for 20 seconds. If three additional wrong user codes are entered, you will not be able to open the safe using the digital keypad for 5 minutes. During the lockout period entry can be made using the override access key.

OVERRIDE ACCESS KEY
If the pass code is unavailable or your keypad fails due to dead batteries or other malfunctions, you can open the safe using the override access key.

REPLACING BATTERIES

Note: The passcode might be reset to the original factory passcode (159) if batteries are removed or become too weak. You should always test your passcode after replacing batteries to ensure it is still active otherwise refer to step 4 of the “Set-up” section located on page 2 to reprogram your passcode.
IMPORTANT: The starter batteries included with this product are for testing purposes only and should be immediately replaced with new alkaline or lithium batteries. It is NOT RECOMMENDED to use Non-alkaline or rechargeable batteries.
Weak or dead batteries should be replaced immediately and all 4 batteries should be changed. To replace the batteries please follow the instructions in the SETUP section. Remember to always remove batteries from safe if not using for an extended period of time. If your batteries are completely dead and you cannot open the safe by using the digital keypad, use the override access key to open safe and access the battery compartment.

IF YOU FORGET THE PASSCODE

1. Use the override access key to open safe.
2. With door open, press red reset button (C) inside door.
3. Yellow light is on; enter new pass code in 30 seconds.
4. Enter pass code (3 to 8 digits) followed by “A” or “B”.
5. Safe will beep and yellow light will turn off.

MOUNTING KIT (Excludes model 5103SL/5103GSL)

You may bolt your safe to the wall or floor to added theft protection and resistance to tipping. Your safe has pre-drilled bolt-down holes in the back panel and in the floor.
To secure your safe to the wall and/or floor:

1. Select a suitable and convenient location for your safe.

2. Empty the safe and remove the carpet.

3. Locate the predrilled holes on the inside of safe.

4. Place your safe in the desired location.

5. Line up the predrilled holes and mark the floor or wall through the holes.
   NOTE: It is not recommended to attempt to bolt to both floor and wall.

6. Move the safe aside to clear marked spots for drilling.

7. Drill holes appropriate for hardware being used and the mounting surface.
   INCLUDED: (2 each – bolts, washers and masonry anchors).

8. Place the safe back over the holes and install the fasteners as required.

9. Once completed, replace the carpet.
   NOTE: Bolting/unbolting of the unit is at the consumer’s expense and discretion. LH Licensed Products is not responsible for any costs incurred if the unit is to be replaced.

If you have any questions about mounting the safe, please check with your local home center/hardware retailer or independent contractor.

REMOVABLE SHELF
Models 5103SL/5103GSL-5110/5110G-5111/5111G If your safe is equipped with a removable shelf, it can easily be removed to accommodate the storage of taller or larger items.

1. Empty shelf of all contents and remove any carpeting
2. Remove by lifting and tilting to side to fit through door opening.
   DO NOT discard shelf. It is recommended that you store it for future needs.

ORDERING NEW / REPLACEMENT KEYS

The following information is required to order keys:

1. PROOF OF OWNERSHIP (1 of 2 Options Below)

   • SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ORDERS ONLY!
   • Copy of sales receipt showing Store, Date & Product Description.
   • Copy of your picture I.D. (Drivers license, passport, regular I.D.).
   • PRODUCT OWNERSHIP VERIFICATION FORM
     If sales receipt is not available, contact us by email or telephone to request a “Product Ownership Verification Form”.

2. ORDER INFORMATION

   • CONTACT INFORMATION
   • Name & Shipping Address
   • E-mail address (If Available)
   • Telephone Number
   • Best Time to Contact You
   • PRODUCT INFORMATION
   • Safe Model #
   • Safe Serial #
   • Lock Key #
   • Quantity of Keys Ordered

3. METHOD OF PAYMENT

   • Telephone:
     Visa or MasterCard

   • Mail:
     Check or Money Order

NOTE: For pricing please contact Consumer Assistance. Contact information is located on the back cover of this manual
Terms subject to change without prior notification.

LOCATING SAFE IDENTIFICATION NUMBERS

• SERIAL NUMBER
  Located on lower right corner on front of safe. Do Not Remove Safe I.D. Tags!

• KEY NUMBER
  4 Digit Number etched on the metal collar located around the key hole.

LIMITED WARRANTY

LH Licensed Products, Inc., (“LHLP, Inc.”) warrants that for seven (7) years from the date of purchase, this product will be free from structural or mechanical defects resulting from materials or workmanship. LHLP, Inc., at its sole option and as the purchaser’s sole remedy under this warranty, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement or repair will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value.

THIS IS YOUR EXCLUSIVE WARRANTY.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This warranty is only valid for the original retail purchaser from the date of initial retail purchase and is not transferable. You must keep the original sales receipt. Proof of purchase is required to obtain warranty service.

LHLP, Inc. dealers, service centers, or retail stores selling this product do not have the right to alter, modify or in any way change the terms and conditions of this warranty. This warranty does not apply to the finish on the product. This warranty does not cover normal wear and tear of parts or damage resulting from any of the following: negligent use or misuse of the product, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than LHLP, Inc. or an authorized service center, improper installation, or exposure to extremes of heat or humidity. Further, the warranty does not cover Acts of God, such as fire, flood, earthquakes, hurricanes and tornadoes.

LHLP, Inc. shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty or otherwise relating to the sale of this product. LHLP, Inc. is also not responsible for: costs associated with removing or installing the product; damage or loss of the contents of the product; nor for the unauthorized removal of the contents; or damages incurred during shipment.

THE ABOVE WARRANTY IS INSTEAD OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND LHLP, INC. DISCLAIMS ANY AND ALL OTHER COVENANTS AND WARRANTIES.

Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty period. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state, or province to province, or jurisdiction to jurisdiction.

CONSUMER ASSISTANCE

EMAIL: LHLPCustomerService@LHLPinc.com
WEBSITE: www.honeywellsafes.com
ADDRESS:
Consumer Assistance Dept.
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746 USA
TELEPHONE: US/Canada 1-877-354-5457 (Toll Free)
Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free)
Austrailia 0011-800-5325-7000 (Toll Free)
Germany/New Zealand 00-800-5325-7000 (Toll Free)
Other Countries XX-310-323-5722 (Toll Charges Apply) XX- Dial U.S. Country Code first
CALL CENTER HOURS: US/Canada 7am – 5pm (PST) Mon – Fri
CALL BACK HOURS: Other Countries 7am – 8pm (PST) Mon – Fri PST**- Local time in Los Angeles, CA, USA

• Insert correct Country Code
  ** Local Time based on Los Angeles California USA

INTERNATIONAL CALL BACK HOURS:
If you need to speak with a consumer assistant and cannot contact us during the Call Center hours above, please send an email or leave a telephone message, including your Name, Telephone Number and the best time for us to contact you during the Call Back hours above and we will make our best effort to contact you and help to answer any of your questions or concerns.

Manufactured by
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746

The Honeywell Trademark is Used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product.

References

• Honeywell Safes
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>