Honeywell HCC10 High Resolution Indoor Box Camera User Guide

: June 17, 2024
: Honeywell

Table of Contents

FCC Compliance Statement
Canadian Compliance Statement
Manufacturer’s Declaration of Conformance
Important Safety Instructions
Package Includes
Key Features
Installing the Lens
Connecting the Wiring
Mounting the Camera
Adjusting the Lens
Configuring the Camera
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**Honeywell HCC10 High Resolution Indoor Box Camera User Guide

**

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND• MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT.

FCC Compliance Statement

Information to the user: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canadian Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is compliant with the essential requirements of the EMC Directive 2004/108/EC, the General Product Safety Directive 2001/95/EC and the RoHS Directive 2011/65/EU, conforming to the requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, EN 60950-1 for electrical equipment safety, and EN 50581 for assessment of electrical and electronic products with respect to the restriction of hazardous substances

Warnings

WARNING Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.

WARNING This device is configured for 12 V DC or 24 V AC operation. Do not connect to higher voltage. Use only with NRTLapproved Class 2 power supplies.

WARNING To prevent the risk of fire or electric shock hazard, do not expose this camera to rain or moisture.

Important Safety Instructions

Read and keep these instructions.
Please ensure that your installation area can safely support the weight of the camera.
Do not install the camera in extreme temperature conditions. Only use the camera where temperatures are within the limits shown in the specifications section of the guide. Be especially careful to provide ventilation when operating under high temperatures.
Do not aim the camera at extreme light sources to prevent damage to the CCD.
This camera is rated for indoor operation. Do not expose this camera to rain or moisture.
Do not touch the camera lens, dome, or bezel (front glass plate).
Do not drop the camera or subject it to physical shock.
Do not use a strong or abrasive detergent when cleaning the camera.

Package Includes

Camera (1)
Manuals (3)
Warranty (1)
C/CS Mounting Ring (1)

Key Features

1/3-inch interline transfer CCD
High resolution: 600 TVL (HCC10/HCC10X); 650 TVL (HCC210/HCC210X)
High sensitivity: 0.1 lux minimum illumination (F1.2, 50 IRE, AGC on)
Configurable day/night settings
Digital noise reduction
Backlight compensation
Auto electronic shutter
Auto gain control
Motion detection (4 programmable zones)
Privacy masking (8 programmable zones)
On-screen display
Alarm input/output
RS-485 port for connecting to a keyboard or DVR
12 V DC or 24 V AC

Installing the Lens

Remove the lens mount cap from the camera (if present).
Screw the lens clockwise onto the lens mount of the camera (A). If you are using a C-mount lens, you will need to attach the C-mount adapter first.
Connect the auto-iris drive cable to the 4-pin connector interface on the side of the camera (B).

Connecting the Wiring

Note Do not turn on the power of any connected equipment until all connections are completed.

Connect the power input of the camera to an external 12 V DC or 24 V AC power supply.
Connect the video output of the camera to the video input of your monitor.
Optionally, make alarm input and output connections.
Alarm input is active when shorted to ground. Alarm out is open collector controlled by alarm in. Absolute maximum alarm out values are 12 V DC and 200 mA.
Optionally, connect the D/N input of the camera to an external day/night control and set the OSD Day/Night menu to EXT1 or EXT2. When the D/N terminal is connected to the ground (G) terminal, the camera is forced into night mode. The camera remains in night mode until the D/N terminal is disconnected from the ground (G) terminal.
Optionally, connect a DVR or keyboard using the RS-485 terminals (D+, D–). Connect T+,T– of the DVR or keyboard to D+, D– of the camera. The default baud rate is 4800, address is 001, and protocol is Pelco-D.

Note The camera address cannot be changed. Only one camera address is supported.

Mounting the Camera

The camera can be installed to a tripod, housing, wall mount, or ceiling mount using the 1/4–20 UNC mounting holes on the top and bottom of the camera.

Adjusting the Lens

After installing the lens and connecting the wiring, you can adjust the lens focus and zoom. If the correct focus cannot be obtained, you can adjust the back focus manually using the back focus screw on the side of the camera.

To adjust the back focus:

Fully open the iris, set the zoom ring (if applicable) to full WIDE, set the focus ring to NEAR.
Loosen the back focus screw, adjust the back focus ring to focus the picture, and then retighten the back focus screw.

Configuring the Camera

After you have installed the lens, connected the wiring, mounted the camera, and adjusted the lens focus and zoom, you can configure the camera settings using the on-screen display (OSD) setup menu.

For more information about setting up the camera, refer to the High Resolution Indoor Box Camera User Guide (800-15952).

Specifications

Video Standard	NTSC, PAL
Image Sensor	1/3-inch interline transfer CCD
Number of Pixels (H×V)	HCC10(X): 768 × 494 (NTSC); 752 × 582 (PAL)

HCC210(X): 976 × 494 (NTSC); 976 × 582 (PAL)
Minimum Illumination| 0.1 lux color @ F1.2, 50 IRE, AGC on
Horizontal Resolution| HCC10(X): 600 TVL HCC210(X): 650 TVL
Video Output| 1.0 Vp-p, 75 ohms
Sync System| Internal, line lock
S/N Ratio| 50 dB or more (AGC off)
Auto Gain Control| 6 dB to 44.8 dB (Manual)
Automatic Electronic Shutter| 1/60–1/100,000 s (NTSC) 1/50–1/100,000 s (PAL)
White Balance| ATW/Push/User1/User2/AntiCR/Manual/Push Lock
BLC/HLC| Off/BLC/HLC
Day/Night| Auto/Day/Night/Ext1/Ext2
Noise Reduction| Y reduction
Motion Detection| Off/On; 4 programmable zones
Privacy Masking| Off/On; 8 programmable zones
Power Consumption| 4 W (max)
Dimensions (L×W×H))| 4.4ʺ × 2.7ʺ × 2.2ʺ (111.0 mm × 68.8 mm × 56.0 mm)
Weight| 0.88 lb (0.4 kg)
Camera Mount| 1/4-20 UNC
Lens Mount| C/CS Mount
Connectors| Lens: 4-pin connector Video Output: BNC connector Power Input: 2-pin terminal block Alarm/DN/RS-485: 6-pin terminal block
Temperature| Operating: 14°F to 122°F (–10°C to 50°C) Storage: –4°F to 140°F (–20°C to 60°C)
Relative Humidity| Less than 90%, non-condensing

www.honeywell.com/security
+1.800.323.4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html

Document 800-15951 – Rev A – 09/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by anymeans without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes