kitchenAid KSSS48FM Built-in Refrigerator Instruction Manual
- June 16, 2024
- KitchenAid
Table of Contents
kitchenAid KSSS48FM Built-in Refrigerator
Specifications
- Product Model Numbers: KSSC36FM, KSSC36QM, KSSC42FM, KSSC42QM, KSSC48FM, KSSC48QM, KSSO36FM, KSSO36QM, KSSO42FM, KSSO42QM, KSSO48FM, KSSO48QM, KSSP36QM, KSSP42QM, KSSP48QM, KSSS36FM, KSSS36QM, KSSS42FM, KSSS42QM, KSSS48FM, KSSS48QM, KSSV42FM
- Electrical: 115-volt, 60-Hz, AC-only, 15- or 20-ampere electrical supply is required. A time-delay fuse or circuit breaker is recommended. A separate circuit serving only this appliance is recommended.
- Cold Water Supply: Connect the ice maker to a cold water line with water pressure between 20 and 120 psi (138 – 827 kPa).
Product Usage Instructions
Electrical Connection
A 115-volt, 60-Hz, AC-only, 15- or 20-ampere electrical supply is required
for the product. It is recommended to use a time-delay fuse or circuit
breaker. A separate circuit serving only this appliance should be provided.
Cold Water Supply
Connect the ice maker to a cold water line with water pressure between 20
and 120 psi (138 – 827 kPa). If you are unsure about your water pressure,
please contact your utility company for assistance.
Cabinet Opening Dimensions
For the overall dimensions and cabinet opening dimensions, please refer to
the provided chart in the user manual. The dimensions vary based on the
specific model number.
Anti-Tip Requirements
Ensure that the product is properly secured to prevent tipping. Follow the
guidelines provided in the user manual for the minimum and maximum
measurements to bottom of solid soffit.
Door Swing Dimensions
Refer to the user manual for the specific door swing dimensions for your
model. The dimensions may vary depending on the model number.
Water Supply Requirements
If the water shutoff valve is located in the base cabinet, make sure that
the access hole through the side of the cabinet is within 1/2 inch (12.7 mm)
of the rear wall. It is recommended to have the water shutoff valve on the
right side cabinet. If the water shutoff valve is not in the cabinets, the
water line can come through the rear wall or floor in the shaded area as
dimensioned in the user manual.
FAQ
Q: Can I use this product with a 220-volt electrical supply?
A: No, this product requires a 115-volt, 60-Hz, AC-only electrical supply.
Q: What is the recommended water pressure for the ice maker?
A: The recommended water pressure is between 20 and 120 psi (138 – 827
kPa).
Q: Can I connect the ice maker to a hot water line?
A: No, it is recommended to connect the ice maker to a cold water line.
Q: Are there different styling options available for this product?
A: Yes, there are other model series available with different dispensing
and non-dispensing options.
PRODUCT MODEL NUMBERS
- KSSC36FM
- KSSC36QM
- KSSC42FM
- KSSC42QM
- KSSC48FM
- KSSC48QM
- KSSO36FM
- KSSO36QM
- KSSO42FM
- KSSO42QM
- KSSO48FM
- KSSO48QM
- KSSP36QM
- KSSP42QM
- KSSP48QM
- KSSS36FM
- KSSS36QM
- KSSS42FM
- KSSS42QM
- KSSS48FM
- KSSS48QM
- KSSV42FM
Electrical
A 115-volt, 60-Hz, AC-only, 15- or 20-ampere, fused, electrical supply is
required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.
Cold Water Supply
Connect the ice maker to a cold water line with water pressure between 20 and
120 psi (138 – 827 kPa). If you have questions about your water pressure, call
your utility company).
OVERALL DIMENSIONS
Other model series dispensing, and non-dispensing, with different styling are available.
see chart following
| Model | Width A (Trim edge to trim edge) |
|---|
36 in. (91 cm)
42 in. (106 cm)
48 in. (122 cm)
| 361/4 in. (92 cm)
421/4 in. (107 cm)
481/4 in. (123 cm)
| Model | Width A |
|---|
36 in. (91 cm)
42 in. (106 cm)
48 in. (122 cm)
| 35 in. (89 cm)
41 in. (104 cm)
47 in. (119 cm)
- When leveling legs are fully extended to 1-1/4 in. (32 mm) below rollers, add 1-1/8 in. (29 mm) to the height dimensions
CABINET OPENING DIMENSIONS
| Model | Width A (as shown above) |
|---|
36 in. (91.4 cm)
42 in. (106.7 cm)
48 in. (121.9 cm)
| 351/4 in. (90.2 cm)
411/4 in. (105.4 cm)
471/4 in. (120.7 cm)
WATER SUPPLY REQUIREMENTS
If water shutoff valve is located in base cabinet, access hole through side of cabinet must be within 1/2″ (12.7 mm) of rear wall. Right side cabinet is recommended. If water shutoff valve is not in cabinets, water line can come through rear wall or floor in shaded area dimensioned above.
ANTI-TIP REQUIREMENTS
- A. Center board 1/4 in. (6 mm) max. above refrigerator
- B. Two, 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards
- C. Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws
- D. Compressor cover
The solid soffit must be within 1 in. (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1 in. (2.5 cm) or one is not available, prevent the refrigerator from tipping during use as shown. Board(s) must be long enough to fully cover the width of the compressor cover. Locate the board(s) so the bottom surface of the board(s) are 84 in. (213 cm) from the floor. Securely attach one or two 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) wood boards to wall studs behind refrigerator. Use 6 – #8 x 3 in. (7.6 mm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1-1/2 in. (3.8 cm). The board(s) must overlap the compressor cover.
DOOR SWING DIMENSIONS
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>