Kingtron W346 3 in 1 Magnetic Wireless Charger User Manual
- June 16, 2024
- Kingtron
Table of Contents
3-in-1 Magnetic Wireless Charger User Manual
Packing List
Product Description
Specification
Model: W346
Output: Phone: 10W/7.5W/5W
Watch: 2.5W
Input: SV/3A 9V/2A
For AirPods: 3W
Compatibility
-
Smartphone
Work For iPhone: iPhone 15,iPhone 15 Plus,iPhone 15 Pro,iPhone 15 Pro Max,
iPhone 14, iPhone 14 Plus,iPhone 14 Pro,iPhone 14 Pro MaxiPhone 13,iPhone 13 Pro,
iPhone 13 Pro Max,Phone 13 mini,iPhone 12,iPhone 12 mini,iPhone 12 Pro, iPhone 12 Pro Max, -
For Apple headphones
Work For Apple Headphones: AirPods 2, AirPods 3, AirPods Pro, AirPods Pro2
Note: not for AirPods 2 non-wireless version -
Smartwatch
Work For Apple Watch: Series 8/Ultra/7/6/SE/5/4/3/2
How to use the product
-
Mobile phone charging: Connect the power adapter (9C/2A recommended) to the USB-C power input port of the magnetic wireless charger, connect the power supply, the charging indicator turns green and turns off after three seconds. Attach the phone to the phone charging position, the blue light of the indicator is always on, indicating that the phone is charging normally. When the phone is fully charged the blue light is always on. If the phone is not charging properly, the green light will flash.
-
Headset charging: place the headset in the headset charging location.
( Note: Please do not wear 0.11in(3mm) silicone shield, otherwise it may lead to poor contact, and can not be charged) -
Watch Charging: 1. Turn the watch module down 2. Place the watch on the wireless charging location and align it with the magnet, the charging indicator on the watch display will light up, indicating that the watch is charging.
Warm Tips
Please pay attention to the following items, otherwise it may cause failures like irregular charging, over-heated charging, intermittent charging, or even no charging.
- Please place your phone/watch/headset in the correct charging area.
- The charging distance is between 0.07in-0.21in(3-8mm), please do not wear protection cases thicker than 0.11in(3mm).
- During the charging process, please make sure there are no metal or magnetic objects around the central 2.36in of the back of the phone.
- he lower the temperature, the faster the charging speed, and the charging speed is faster in winter than in summer.
- Please do not charge in a high temperature and humid environment, s as to not to damage the circuit.
- Please make sure that your phone support magnetic charging, or wear a magnetic phone case;
- If charge a wireless charging mobile phone without magnetic function, please lay the charging station flat, but it is not recommended. Because it may cause lower charging speed, or cause heat. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance
7.87in(20cm) between the radiator & your body.
This device complies with part 15 of the FCC rules operations subject to the
following two conditions:
(1)this device may not cause harmful interference. (2)this device must accept
any interference received including. interference that may cause undesired
operation.
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in are sidential installation. This equipment generates uses and
can radiate radio frequency energy and if not installed and used in accordance
with the instructions may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur ina particular
installation If this equipment does cause harmful interference to radio or
television reception which can be determined by turning the equipment off and
on. The user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.