Evajoy NB-DL003 Floor Lamp with Shelves User Manual
- June 16, 2024
- EVAJOY
Table of Contents
4-TIER SHELF
FLOOR LAMP
NB-DL003
User Manual
SAFETY INSTRUCTIONS
- Please keep it in a dry environment and don’t touch the lamp with wet hands.
- For a longer service life, please do not use the lamp in hot or corrosive surroundings.
- Make sure that the voltage is 120V which is standard for the US.
- Unplug the lamp before cleaning.
- Each shelf can take a maximum load of 50 Lb. Make sure not to put more than 50 Lb on each shelf.
- If you have any questions, please contact us by E-mail.
- The total power of the 1AC output port is 1000W. Do not use electrical appliances that exceed the power.
Specifications
| Input | AC 100-240V |
|---|---|
| CRI | ≥80 |
| Luminous Flux | 850 lm |
| Color Temp | RGBCW |
| Light Source | LED |
KNOWING YOUR FLOOR LAMP
Package Contents
ASSEMBLING YOUR FLOOR LAMP
Step 1:
First, use screw (E) to fix 4 steel frame poles (I) and bottom panel (A)
together, then stick the non-slip mat (M) on the four corners of the bottom
panel. Available tools: screwriver with hexagon wrench (L).
Step 2:
Put the 4 screws (F) into the 4 steel frame poles (I) and tighten them, and
snap the middle panel (B) into the screws. Screw in 4 steel frames poles (I)
again on the screw sticking out from the upper end. Tighten the screws to
prevent the light stand from shaking afterward.
Step 3:
Repeat step 2, fix the USB panel (C) on the shelf, screw in the 4 steel frame
poles (I) and make sure to tighten.
Step 4:
Fix the top panel with light socket & wire (O) on the 4 steel frame poles (I),
tighten the bottom wing nut under to fix the light socket. Install the charging
case on the USB panel (C), use 2 screws (G) to secure the charging case. Use 4
screws (F) to fix the top panel (D) and poles (I).
**** Raised hoook face up!
Step 5:
Unfold the lamp shade (H), put the iron frame for lamp shade (J) into the
bottom of the lamp shade.
Step 7:
Use wire fixing accessories (N) to fix the wires neatly on the light stand to
make the appearance more beautiful and neat.
USING YOUR FLOOR LAMP
ON/OFF: Pull the chain switch to turn on/off the lamp.
Control via CozyLife
- Download CozyLife APP, and sign in.
- Add device in the pop-up, and choose the preferred interface.
- Ensure that your phone Bluetooth is enabled and is connected to WiFi (only supports 2.4G WiFi network);
- Launch the “CozyLife” APP, the product will be automatically recognized, and a prompt box will pop up at the “+” in the upper right corner;
- Click the prompt box, select the device to be connected, click Next, and enter the WiFi setting page;
- After entering the WiFi password, wait for the network configuration to complete.
https://dohome.doit.am/cozylife/downLoad.html
CLEANING AND MAINTENANCE
Note:
Always turn off the light and unplug the cord before cleaning or maintenance.
FCC STATEMENT:
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
techsupport@tyutech.com
www.tyutech.com
Manufacturer: Shenzhen Aspiron Technology Company Limited Address: 3rd Floor,
Yiben Building, No.1063 Chaguang Road, Xili Street, Nanshan District,
Shenzhen, Guangdong, China
Made in China
Questions or Concerns?
techsupport@tyutech.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>