XTOOL P2 Laser Cutter and Engraver User Guide

XTOOL P2 Laser Cutter and Engraver User Guide

List of items

xTool P2|
Power cable|
USB cable (Type-C)|

Smoke exhaust pipe components

---|---|---|---

Antifreeze

|
Funnel|
Basswood 3 mm|

Corrugated paper 3.5 mm

Transparent acrylic

|
Screw driver|
Hex key|

Quick Start Guide

Instructions

|

Screw M3*6 (spare parts)

| Screw M3*22 (spare parts)|

Material clamp

Open the box and take out all the items

1. Open the lid and take all the items out
   

2. Unscrew the screw that fixes the baseplate
   

3. Take out the foam and acrylic sheets and put the baseplate back to the machine
   
   

4. Tighten the screw that fixes the baseplate
   

Meet your xTool P2

1. Button
2. Annular indicator
3. State display screen
4. Laser tube
5. Water tank
6. Emergency stop switch

|

7. Power switch
8. Power port
9. Fire safety set port
10. Tube fitting
11. Smoke outlet

12. Distant-view camera
13. Close-view camera
14. Laser module
15. Extension port| 16. Network port
17. USB port (Type-C)
18. Slat
19. Baseplate

Preparations

1. Check the casing of the machine. If it is severely damaged, do not use the machine and contact x Tool after-sales services.
   

2. Remove the sticker used to prevent the lid from locking and turn the emergency stop switch to reset it.
   

3. Manually move the laser module to check whether it can move properly. If it can’t, do not use the machine and contact xTool after-sales services.
   

4. Check the laser tube. If it is cracked or damaged, do not use the machine and contact x Tool after-sales services.

5. Unscrew the screws that fix the rear cover and remove it
   
   

6. Check whether the laser tube is cracked or damaged
   

7. Fill the water tank with antifreeze
   

   You need to prepare a measuring glass to measure purified water.|
   If you can’t find a measuring glass at home, you can store the antifreeze in another container and use the bottle of the antifreeze to measure purified water.|
   |

   • Do not pour the antifreeze directly into the water tank.
     Determine the volume of antifreeze to be used according to the annual lowest temperature in your region first.

   • Ensure that you use purified water to prepare the antifreeze. Tap water contains impurities and bleach, which may cause too many bubbles, affecting the working of the laser tube and even damaging the laser tube.

   • You need to fill the water tank twice. Strictly follow the steps to fill the water tank, using the recommended volume of antifreeze and avoiding overflow.Fill the water tank with antifreeze

8. Determine the volumes of antifreeze and purified water to be used

  * If the annual lowest temperature in your region > 0℃  

Annual       lowest temperature     in your region (℃)| Concentration (%)| First filling| Second filling
---|---|---|---
Antifreeze(ml)| Purified Water (ml)| Purified water(ml)
T ＞ 0| 0| 0| 1100| 300

• If the annual lowest temperature in your region ≤ 0℃
  nnual         lowesttemperature       in your region (℃)| Concentration (%)| First filling| Second filling
  ---|---|---|---
  Antifreeze(ml)| Purified water (ml)| Purified water(ml)
  –10| ≤| T| ≤| 0| 20| 280| 820| 300
  –20| ≤| T| ≤| –10| 35| 490| 610| 300
  –30| ≤| T| ≤| –20| 45| 630| 470| 300
  –40| ≤| T| ≤| –30| 50| 700| 400| 300
  –50| ≤| T| ≤| –40| 60| 840| 260| 300

2. Open the cap of the water tank and insert the funnel into the opening  

3. Complete the first filling  

Pour the required volume of antifreeze into the water tank, and then slowly pour the required purified water in. Observe the water level during the filling to avoid overflow.

4. Connect the machine to a power supply and turn on the machine  

5. Complete the second filling Wait 30s for the water level to descend in the water tank, pour the required purified water in, and then close the cap of the water tank. Observe the water level during the filling to avoid overflow.  

6. Fit the rear cover back to the machine and tighten the screws  

6. Install the smoke exhaust pipe
   |
   If you have purchased a smoke purifier, follow the instructions to connect it to xTool P2.
   ---|---

Use xTool P2

1. Download and install xTool Creative Space (XCS)
   

2. Connect xTool P2 to your computer and connect it to XCS
   
   You can start your creation after connecting them.
   For details about how to use XCS to operate xTool P2, see makeblock.com/cn/docs/xtooljp.

References

• xTool Support Center
• xTool Creative Space: Software Download for All xTool Machines

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>