UardEr 456807 Fingerprint Door Lock with 2 Levers Set User Guide

G10PRO SMART DEADBOLT
Installation and User Guide

456807 Fingerprint Door Lock with 2 Levers Set

Required tools (not included)

www.WeAreLocksmiths.com
24Hr online service
Guarderservice@gmail.com
Video Demo QR Code

https://ma3you.com/a/RryLzNA/https://ma3you.com/a/AXrV1DO/

1. Prepare the door and check dimensions
2. Install the latch and strike
3. Install the exterior keypad and the interior assembly
4. Lock components

PROGRAMMING

if you make a mistake during programming,press the’ ” button repeatedly until the keypad lights up. Then start over.
“ ” Double-click + number” to enter the programming mode, which can prevent accidental touches from entering the programming state-
Remark : 1.The initial state will not be auto-lock. 2.Please Detect 1(Left) / 2. (Right) Direction before initial setup.
The default programming code is 123456. Programming Code=PC USER Code=UC

Features

• three ways to access: code,key and fingerprint
• -25 to 70 °C temperature range
• Low power consumption, 4 AA for 1 Years Battery Life or 50,000 times unlock
• Backlit keypad for use in low light environments
• 1 master code and 300 user codes
• Passage mode for hassle-free entry
• Color LED indicator lights up to show when codes and commands have been successfully entered
• Built-in disguise feature to protect your codes from prying eyes
• Low battery warning indication

Specifications

The color of the light indicates & beep,the status of the lock.
Blue
• programming in progress, blue flashing state
Purple
• acorrect master passcode o r user passcode was entered, one long beep
Red
• an incorrect master passcode o r user passcode was entered, three short beep . there was an error in programming, three short beep
• red blinking and beep after keypad backlit o ff indicates critically low battery| The lock comes preset with default programming passcode 123456 . Used to put the lock in programming mode
• Can unlock the lock,4-10 digits in length
• Must be different from all of the User Codes currently in the lock.
If you forget the master passcode, you can reset the lock to factory settings,which restores the default master passcode. See Restore Factory Settings

Programming Button ” ”

| User Code(UC)
• Programming Button is for entering codes, clearing errors and setting function.
In manually mode, Long press the “ ” 3 seconds to lock| • The lock comes not preset any User Code
• Used to unlock the lock
• Must be different from the master passcode and other user passcodes . Up to 300 possible User Codes can be stored in the lock at one time

Set up private mode

Press and hold the Deadlock button for 2 seconds
**** After the Deadlock function is turned on, A only the master code can unlock , and all user code cannot unlock (use the master code to unlock the lock will remove the Deadlock restriction)

Restore Factory Settings

To delete all user codes, including the master code, follow the instructions below:

1. Use a screwdriver to remove the screws from the interior cover.
2. Press and hold the reset button for 5 seconds until “bi,bi”purple light flashing are heard, The master passcode will return to the manufacturer default code ‘123456’.

**** After restore factory , Change the master passcode as soon as posible! beacuse of the master passcode can unlock the door.

Simple Troubleshooting

The door cannot be locked and purple light flashing when you press the Programming button| Causes :
1.Door lock latch unlocking direction is not selected correctly .
2.The initial state will not be auto-lock.
Solutions :
1.Please detect Left / Right hand door unlock direction,
→ 50 →   PC → → 1（Left unlock）or 2 (Right unlock)→ →   → →    → →   .
2.Toggle autolock on&set time delay , → → 52→ → PC→ → 05→ .05-69 seconds delay-time available.
Situation 2| Causes / Solutions
The passcode and key of the door lock
cannot be unlocked.| Causes:
When the door lock is installed, the correct unlocking direction is not selected.
Solutions : In the rear lock, choose “L” for the left door, corresponding to the horizontal “—” Turn-piece, and choose “R” for the right door, corresponding to the vertical “l” Turnpiece.

Other online update situation scan QR

https://ma3you.com/a/AQoLq0O/

Warranty
Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, cuarder extends a lifetime limited mechanical and finish warranty and a one- year limited electronics warranty to the original consumer user (“original User”) of our Guader brand product against defects in material and workmanship, as long as the original User occupies the residential Premises upon which the Product was originally installed.See answers www.WeAreLockSmiths.com for specific warranty details.
WARNING
This Manufacturer advises that no lock can provide complete security by itself. This lock maybe defeated by forcible or technical means.
or evaded by entry elsewhere on the property.No lock can substitute for caution, awareness of your environment, and common sense.
Builder’s hardware is available in multiple performance grades to suit the application.In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>