CONAIR LWD1RN Twin Foil Battery Bikini Trimmer Instruction Manual

MODEL LWD1RN
Instruction Manual Twin Foil
shaver

Congratulations on the purchase of your new twin-foil wet/dry shaver for women.
For maximum satisfaction when using this quality product, please take a minute to read the following operating and care instructions.
Thank you for choosing Conair, the #1 brand in personal care appliances.

SAVE THESE INSTRUCTIONS WARNING

1. Women whose skin is sensitive to cosmetics or easily irritated by shaving, or who suffer from a skin allergy, should test one section of the leg or arm before using the shaver.

2. The foils are thin and precisely finished pieces. Do not press hard against the foils or drop foils. A warped or distorted foil will produce poor shaving results.
   Also, a damaged foil may cause skin injury. A damaged foil should be replaced immediately.

3. When cleaning, use cold or warm water.
   Do not use hot water, seawater, or cleaners, as they can cause damage to the waterproof seals.

4. Do not leave the entire unit submerged in water for a long period of time.

5. To prevent possible damage to the foils and the cutter, women who use underarm deodorant must thoroughly clean and air-dry the foils and cutter after each use. Failure to do this may result in corrosion of the inner blades.

6. This appliance is not a toy. Keep away from children.

OPERATING INSTRUCTIONS IMPORTANT

This shaver has been engineered to give you a clean, close, smooth shave. It requires 2 AAA batteries (not included). We recommend using longer lasting alkaline batteries in your shaver.
If you are not going to use your shaver for a long period of time or if the batteries are dead, remove or replace the batteries from the unit.
Use your shaver exclusively for three to four weeks so that your legs and underarms adjust to the shaver. At first, your shave might not be as close as you expect. However, this is normal.
It takes time for your skin and hair to adjust to the new procedure and for you to learn how to effectively use the shaver.
Caution: Most blade users will push too hard and therefore not get a satisfactory shave. You must press gently so the hair can get into the holes of the foils. Pressing too hard makes the hair flat. Please be patient; use your shaver 10 to 12 times before you judge its performance.

FOR HOUSEHOLD USE ONLY

OPERATING INSTRUCTIONS

1. Remove the battery compartment cover by pushing in and down toward the bottom of the shaver.
2. Align the 2 AAA batteries with the positive and negative positions indicated inside the battery compartment. Being careful not to bend the clips, insert the negative end of each battery first so it will slip easily into place.
3. Return the battery cover to its original position by pushing it in and up until you hear a small click as it locks into place.
4. To use your shaver, remove the transparent cover and push ON/OFF switch upwards to the ON position.
5. After you finish using your shaver, push down on the ON/OFF switch to turn the shaver off.
6. Ensure the batteries are installed correctly with regard to polarity (+ and -).
7. Remove the batteries if they are no longer functional or if the shaver is left unused for an extended period of time.
8. Clean the battery contacts and also those of the device prior to battery installation.
9. Remove used batteries promptly.
10. Always purchase the correct size and grade of battery most suitable for the intended use.
11. Replace all batteries of a set at the same time.
12. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium or nickel metal hydride) batteries.

CAUTION
Do not immerse any part of the unit in water or other liquid.
The outer foils and cutters are delicate and must be handled very carefully.
BEFORE SHAVING

1. Before wet shaving, you may wish to prepare your legs and underarms with shaving cream or soap. If a soapy lather is applied to the skin, the shaver will glide smoothly over the skin and clean away oil residue, while at the same time removing hair. Caution: Do not use shaving gels, as these products can clog your shaver foils.
2. When dry shaving, be certain that your skin is clean. If you have sensitive skin, you may want to apply talcum powder before and after you shave.
3. Clean your shaver after each use. This will ensure the best performance. (Please refer to “How to Clean Your Shaver” section for further instructions.)

INSTRUCTIONS FOR USE

1. Slide the main switch up to the ON position.
2. After each shave, switch the unit off and clean shaver head.

SHAVING YOUR LEGS/BIKINI AREA
NOTE: Pushing the shaver against the skin too hard will not allow the hairs to enter the foils and be cut. Experience will help you determine just the right pressure to use to maximize performance.

1. Prepare your legs for wet or dry shaving.
2. Turn shaver on.
3. Shave with smooth, steady strokes up and down your skin.
4. Keep the full shaving head in contact with your skin.
5. For best results, shave against the direction of hair growth.
6. The shaver also has a bikini pop-up trimmer for your complete shaving needs.
7. When you finish shaving, turn the shaver off.

Important: After several uses, you will be able to determine the optimum shaving method for your legs and bikini area. SHAVING YOUR UNDERARMS

1. Prepare your underarms for wet or dry shaving. (Be sure that your skin is clean and free of deodorant.)
2. Turn the shaver on.
3. Lift your arm until the skin under the arm stretches slightly.
4. Use the trimmer portion first to remove any long hair, stroking trimmer against the direction of hair growth.
5. Hold the shaver so that it is in full contact with your skin, and shave with gentle strokes.
6. It is important to press lightly. Pressing too hard may lead to skin irritation.
7. When finished shaving, turn the shaver off.

Important: After several uses, you will be able to determine the optimum shaving method for your underarms.

HOW TO CLEAN YOUR SHAVER

1. Make sure unit is in the OFF position before cleaning your shaver.

2. Hold shaver head and lift up from the back, then press foil frame release buttons on each side and lift up (the cutter is now in view).
   Be careful not to push on the foils. They are delicate and can easily be damaged. (FIG.1)

3. Rinse the shaver cutter and foil frame under running water or in a sink. Do not use hot water.
   Use only warm or cold water.

4. After rinsing, allow the foil frame and cutters to air-dry before closing foil frame and shaver head.
   Replace shaver head back onto the shaver until it clicks into place. Wipe the surface of the main unit with a dry towel. Do not dry the foil area. Let the shaving head air-dry.

5. The cutters can also be cleaned with a cleaning brush.

6. If the body of the shaver becomes dirty, wipe off with a damp cloth and mild detergent or soap. Never use thinners, other solvents, or any harsh cleaners.

7. Once dried, carefully place the protective cap on.

CAUTION

1. When shaking off excess water, hold the main unit firmly to prevent releasing the head assembly or dropping the unit.
2. Do not use a dryer or heater to dry the shaver. This may result in malfunction or damage to the shaver.

NOTE: At the end of the batteries useful life, under various state and local laws, it may be illegal to dispose of these batteries into the municipal waste stream. Check with your local solid waste officials for details on recycling options or proper disposal in your area.

REPLACING THE FOIL FRAME & CUTTERS
Replace the foil frame when you find you have to push harder on the shaver to get a close shave, or if you have to go over your leg area more often to get a smooth result. It is also time to replace the foils if you experience skin irritation. Replacement time will depend on how often you use your shaver and how quickly your hair grows.
Caution: Never replace the cutters without replacing the foils as well.

1. Remove the foil frame (see FIG. 2).
2. Push one side of the inner blade to unlock it and take out (see FIG. 3).Caution: Make sure you do not lose the little spring under the cutter, as it will be needed for the new cutter (see FIG. 4).
3. Hold the new inner blades firmly on the sides and guide them gently into the inner blade mount, one side at a time, until they lock into place.
4. Press firmly until the unit snaps into place.
5. Replace the foil frame (see FIG. 5).

REPLACING THE POP-UP TRIMMER ASSEMBLY

Note: We do not recommend replacing the trimmer assembly yourself. Take or send the shaver to a Conair Service Center, because this requires a special tool for replacement. For most users, these trimmers will stay sharp for as long as you own your shaver.

LIMITED TWO-YEAR WARRANTY

(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the service center listed on back, together with your purchase receipt.
California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
For shaving tips and information on Conair appliances, call 1-800-3-CONAIR or visit us on the web at www.conair.com
REPLACEMENT PARTS:
This shaver uses the following replacement parts, which can be ordered directly from Conair by calling customer service at 1-800-3-CONAIR.
CSP21 Replacement Foil and Cutter

Please register this product at
www.conair.com/registration
Service Center
©2021 Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
stock.image
20PG074867

References

• Conair LLC Consumer Products for Haircare, Beauty, Wellness, Home and Travel
• Welcome | Conair

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>