Breezary 30007 52 Inch Ceiling Fan With Light User Manual

Breezary 30007 52 Inch Ceiling Fan With Light

Product Information

Specifications:

• Item Name: 52 Inch Ceiling Fan with Light
• Model   Number: 30007
• Dimensions:
  • Height: 13.8 inches
  • Width: 52 inches
  • Depth: 12 inches

Product Usage Instructions

Installation:
To install the ceiling fan with light, follow these steps:

1. Secure the hanger to the metal outlet box.
2. Hang the ceiling fan on the hanger with the hanger ball groove aligned with the hanger boss.
3. Attach the fan blades to the motor using blade screws.
4. Assemble the lamp housing by feeding the wire through the center hole and fixing it with screws.
5. Install the lampshade by turning it clockwise to lock it into place.
6. Place the receiver in the hanger.
7. Wire the fan according to the provided wiring diagram.
8. Attach the canopy to the hanger with screws and then add the canopy cover.

Troubleshooting Guide:

• Avoid using this product with any variable wall control to reduce the risk of fire or injury.
• Clean the fixture by turning off the power, allowing it to cool, and wiping it with a clean dry cloth
• Check and retighten all screws before installation.

Balancing Kit:
To balance the fan, follow the instructions provided in the user manual for adjusting the jam screws and ensuring proper alignment.

FAQ

• Q: Can I use a variable wall control with this ceiling fan?
  A: It is recommended not to use any variable (rheostat) wall control with this product to avoid potential fire or injury risks.

• Q: How do I clean the fixture?
  A: Turn off the power, allow the fixture to cool, and wipe it with a clean dry cloth to clean it effectively.

• Q: What should I do if the fan is not balanced?
  A: Follow the instructions provided in the user manual for using the balancing kit to adjust and balance the fan properly.

INSTALLATION & USER MANUAL
52 INCH CEILING FAN WITH LIGHT

ITEM #30007
Customer Service: support@breezary.com

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked ” Acceptable for Fan Support of 35 Ibs. (15.9 kg) or less.”
4. Do not place objects in the path of the blades.
5. To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth
6.  After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
7. All screws must be checked and retightened where necessary before installation.

• WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry.
• WARNING: To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control.
• WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert objects. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 Ibs. (15.9 Kg) or less” and use screws provided with the outlet box.
• WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring
• WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall – control / switch.
• CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.

Dimension Reference

Hardware Included

Fan Parts Included

Exploded View

Installation Instructions

Step1 MOUNTING

•  Take out fan downrod.
• Remove cotter pin and bolt from downrod.
• Take out fan motor housing.
• Loosen jam screw in yoke until it is flush with the inside surface.
• Place the downrod inside the canopy, canopy cover, and yoke cover.
• Route wires exiting motor through yoke cover, canopy and downrod.
• Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires.
• Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
• Secure downrod in position by tightening jam screws.
• Slide yoke cover down and it will flush with the motor housing.

CAUTION: To ensure wobble-free operation and to avoid damage to the fan, the downrod anc the set crew must be completely tightened.

Step2 INSTALL MOUNTING BRACKET
WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To UL/CSA Listed Outlet Box Marked Acceptable for Fan Support And Use Mounting Screws Provided With The Outlet Box

• Secure hanger to metal outlet box.
• The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss.

Step3 Attaching the Fan Blades.

•  Attach the blade to the motor with blade screws.
• Repeat this step for each blade assembly.

Step4 Assembling the lamp housing

•  Feed the wire through the center hole of the lamp housing.
• Fix the lamp housing with screws.
• Connect the motor end plug to the light source end socket.

Step5 The lampshade installation

• Install the lampshade to the lamp housing by turning clockwise to lock it into place.

Step6  The receiver installation

• Put the receiver in the hanger.

Step7 Wiring the Fan

•  Wiring according to the wiring diagram.

NOTE: Once ground wires are connected, carefully tuck all wires and marottes into the metal box making sure that the wires are clear of the hemisphere and downrod when positioned in hemisphere and downrod when positioned in mounting bracket.

Step 8 Attaching the Canopy and Canopy cover

• Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely.
• Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)

CONGRATULATIONS! YOU HAVE COMPLETED THE INSTALLATION

FUNCTION INSTRUCTION OF EMITTER

• Open battery cover on the hand-held remote and install battery, pair of AAA of emitter(1.5V) that are not included.
• If the emitter can not control the fan, learning code matching mode is used between emitter and receiver. Turn on the power switch, press the “SETUP” key within 3 seconds, the receiver issued a “tick” two sounds, the pair code is successful. If not successful, turn off the power for a minute an repeat the above.
• When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
• When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
• Please take out the battery from the emitter when leaving unused for long time.
• When installing the fan, the fan ceiling cover don’t press the antenna (or other wire), it is easy to breakdown the wire and short-circuited.
  1. All off
  2. Fan forward rotating
  3. Natural wind
  4. Speed control
  5. Match code/Fan off
  6. Timer Light switch on/off (Color temperature can be selected)
  7. Fan reversal rotating
  8. Turn off the beeping After powering on, press “4H” on the handle immediately After hearing the beep, release the “4H” button to turn off the beeping. (If you need to turn the prompt sound back on, turn off the power first, then turn it on again, and repeat the above actions)

Light Memory Function :

1.  The default light color when the ceiling fan is turned on
2. The light will lock in a specific color temperature after turning on the light for 10 seconds
3. The color temperature will be the same as the last time when turning on the light next time.
   Notice: If you turn it on and off immediately, it will change color.

Troubleshooting Guide

If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases these installation errors may be mistaken for defects. If you experience any faults please check this troubleshooting quite.

| Problem| Suggested Remedy
---|---|---
1| If fan does not start.|

• Check the main and branch circuit fuses or breakers.
• Check the line wire connections to the fan and switch wire connections in the switch housing.
• Check the battery in the remote control.
• Ensure you are in the normal range of 10-20 feet.

2| If fan sounds noisy.|

• Ensure all motor housing screws are snug.
• Ensure the screws that attach the fan blade bracket to the motor hub are tight.
• Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
• Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.
• If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
• Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
• Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

3| If fan wobbles.|

• Check that all blades are screwed firmly into blade holders.
• Check that all blade holders are tightened securely to motor.
• Make sure that canopy and mounting bracket are tightened securely to ceiling
• junction box and junction box is mounted firmly to ceiling joist.
• Most fan wobble problems are caused when blade levels are unequal. Check this
• level by selecting a point on the ceiling above the tip of one of the blades keeping measure within 1/8 in. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all blade levels are not equal you can adjust blade levels by the following procedure. To adjust a blade tip down insert a washer(not supplied)between the blade and blade holder at the screw closest to the motor. To adjust a blade tip up insert washer(not supplied)between the blade and blade holder at the two screws farthest from the motor.
• If blade wobble is still noticeable interchanging two adjacent (side by side)blades can redistribute the weight and possibly result in smoother operation.

4| If light does not work.|

• Check blue wire from fan to make sure it is connected to hot wire from the house.
• Check for loose or disconnected wires in fan switch housing.
• Check for loose or disconnected wires in light kit.
• Check for faulty light bulbs.
• CAUTION: Make sure main power is turned off before entering switch housing.
• If the fan light shuts off shortly after being switched on it may be due to excessive

current demand. Turn off power to the fan and replace the light bulbs with lower wattage bulbs. Turn on power to the fan using the pull chain, wall switch, or remote control (whichever is installed on the particular fan).

Balancing Kit

The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1. Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
2. Turn off the fan and allow it to a come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
3. Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
5. Remove the clip and install a balancing weight to the top of blade along the center line near the point where the clip was positioned.
6. If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights.

References

• Breezary Ceiling Fan - Online Ceiling Fan Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>