ManualsPro AIMCO AIMCO VC-101-2(A) Vacuum Tank User Manual

AIMCO VC-101-2(A) Vacuum Tank User Manual

May 15, 2024
AIMCO

AIMCO VC-101-2(A) Vacuum Tank

AIMCO VC-101-2\(A\) Vacuum Tank

DESCRIPTION AND LAYOUT

Description And Layout

PROCEDURES

WARNING:

  • Read all instructions before operating this equipment.
  • Wear proper protective gear.

AIR PRESSURE:

  • 75-80 PSI

ELECTRIC:

  • 5 AMP 110 VAC

SETTING UP VACUUM TANK:

  • Connect 3/8″ I.D. air hose to air inlet with full flow 3/8″ fittings.
  • Plug electric cord into surge protected power strip plugged into 110 VAC outlet.
  • Turn power switch on.

USING VACUUM FILL SYSTEM:

  1. Remove lid from tank.

  2. Remove the oil fill plug from the pulse unit and turn torque adjuster all the way out counter-clockwise.
    Note: Make sure the driving blade is not blocking the oil fill hole.

  3. Set pulse unit or units into the tank and onto the plate. Note: Make sure the plate is in the raised position.

  4. Pour Manufacturer Recommended Hydraulic Pulse Fluid into the tank so that the fluid level is approximately 1 inch (25 mm) from the top of the liner casing being serviced.
    Note: Insure that the Manufacturer Recommended Hydraulic Pulse Fluid is stirred vigorously to insure consistency.

  5. Put lid back on tank.
    Procedures
    PROCEDURE FOR USING VACUUM FILL TANK SYSTEM
     USING VACUUM FILL SYSTEM:

  6. If you have the VC-101-2A, with the switch in the auto position, push the start button and proceed to step 10.
    Procedures

  7. If you have the VC-101-2 slide the slide switch over so the vacuum starts.
    Procedures

  8. After ten minutes with the vacuum in the green, lower the plate down into the oil.

  9. After 30 seconds with plate lowered, turn the vacuum off. Once the normal air pressure returns, raise the plate on the inside of the tank.

  10. Remove the lid from the tank.

  11. Remove the excess oil from the top of the Pulse Unit so that the oil is level with the top of the oil fill hole.

  12. Draw off the recommended amount of oil from the Pulse Unit and install Oil Fill Plug back into the Pulse Unit.

  13. You are now ready to test your tool.

Fill, Draw, & Torque Sheet

Key Model of this Tool Group| Full Volume of Liner Oil in Pulse Unit (approx.)| Volume to be Removed from the Full Volume (approx.)| Torque to Tighten Liner Casing Setter (approx.)| Torque to Tighten Liner Casing Setter (approx.)| Load to Press on Rear Liner Plate| Load to Press on Rear Liner Plate
---|---|---|---|---|---|---
| | | | | Hydraulic Press| P.T.R.F.
Model| cc’s| cc’s| NM| Ft-Lbs| Tons| Ft- Lbs/Nm
ALPHA-45(S)(D) & 61(D)| 5.0| 0.45+/-.05| 70+/-5| 52+/-4| |
ALPHA-50(S)(D) & L61(D)| 5.0| 0.50+/-.05| 70+/-5| 52+/-4| |
ALPHA-50MC, 60MC & 70MC| 5.0| 0.45+/-.05| 70+/-5| 52+/-4| |
ALPHA-60(S)(D)| 6.2| 0.55+/-.05| 85+/-5| 63+/-4| |
ALPHA-70(S)(C)(CH)| 8.8| 0.80+/-0.1| 110+/-5| 81+/-4| 2| 40/54
ALPHA-80| 12.0| 1.00+/-0.1| 135+/-5| 100+/-4| 2| 40/54
ALPHA-80MC & 90MC| 6.2| 0.55+/-.05| 85+/-5| 63+/-4| |
ALPHA-90| 14.0| 1.00+/-0.1| 150+/-5| 110+/-4| 3| 60/81
ALPHA-100| 19.0| 1.70+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ALPHA-100MC & 101MC| 12.0| 0.80+/-0.1| 135 +/-5| 100+/-4| 2| 40/54
ALPHA-110MC| 12.0| 0.95+/-0.1| 135+/-5| 100+/-4| 2| 40/54
ALPHA-130| 24.0| 2.00+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ALPHA-130MC| 24.0| 1.80+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ALPHA-140 & 140MC| 31.5| 2.30+/-0.1| 200+/-10| 148+/-7| 3.5| 70/95
ALPHA-160| 48.0| 2.40+/-0.1| 260+/-10| 192+/-7| 4| 80/108
ALPHA-180| 48.0| 4.80+/-0.1| 290+/-10| 214+/-7| 4| 80/108
ALPHA-T40D(S), T42D(S)(P), T45(S)(D)(P), T46(D), T47(S)(D)(P), T50(D) & T52(D)| 5.0| | 70+/-5| 52+/-4| |
ALPHA-T60(D) & T62(D)(MI)| 6.2| | 85+/-5| 63+/-4| |
ALPHA-T65(S) & T70(S)(C)(CH)| 8.8| 0.75+/-.05| 110+/-5| 81+/-4| 2| 40/54
ALPHA-T80| 12.0| 0.80+/-.05| 135+/-5| 100+/-4| 2| 40/54
ALPHA-T90| 14.0| 0.95+/-.05| 150+/-5| 110+/-4| 3| 60/81
ALPHA-T100| 19.0| 1.40+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ALPHA-T130| 24.0| 1.80+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ALPHA-T140| 31.5| 1.90+/-0.1| 200+/-10| 148+/-7| 3.5| 70/95
BP-T40 & BP-T50| 5.6| 0.30+/-0.01| 85+/-5| 63+/-4| 1| 20/27
BP-T60| 6.2| 0.41+/-0.01| 85+/-5| 63+/-4| 1| 20/27
U-50EC| 5.0| 0.15| 50+/-5| 37+/-4| |
U-60EC| 8.5| 0.35| 70+/-5| 52+/-4| |
U-80EC| 9.0| 0.40| 70+/-5| 52+/-4| 3| 60/81
U-100EC| 18.0| 0.90| 70+/-5| 52+/-4| 3| 60/81
U-300SD, U-310SD, U-350(S)(D)| 5.0| 0.15| 50+/-5| 37+/-4| |
U-410(S)(D)| 8.5| 0.35| 70+/-5| 52+/-4| |
U-480, U-501| 9.0| 0.40| 70+/-5| 52+/-4| 3| 60/81
U-610, U-610T| 13.0| 0.55| 70+/-5| 52+/-4| 3| 60/81
U-700, U-700T| 18.0| 0.90| 70+/-5| 52+/-4| 3| 60/81
U-800, U-800T| 20.0| 1.00| 90+/-5| 67+/-4| 3| 60/81
U-900, U-900T| 25.0| 1.25| 100+/-5| 74+/-4| 3| 60/81
U-1000, U-1000T| 32.0| 1.70| 110 +/-5| 81+/-4| 3| 60/81
U-1301, U-1301T| 38.0| 2.00| 120+/-10| 89+/-7| 4| 80/108
UA-40(S)(D)MC, 400AMC & UA-50(S)(D)MC, 500AMC| 7.0| 0.35+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
---|---|---|---|---|---|---
UA-60(S)MC & 600AMC| 8.2| 0.40+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UA-70(S)MC & 700AMC| 10.3| 0.70+/-.05| 110+/-5| 81+/-4| 2| 40/54
UA-80AMC & 800AMC| 12.0| 0.80+/-.05| 110+/-5| 81+/-4| 2| 40/54
UA-90MC, 90AMC, 900AMC| 15.8| 0.90+/-.05| 150+/-5| 110+/-4| 3| 60/81
UA-100MC, 100AMC, 1000AMC| 21.7| 1.50+/-0.1| 185+/-5| 137+/-7| 3| 60/81
UA-130MC, 130AMC, 1300AMC| 29.4| 1.50+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UA-150MC| 35.7| 2.0+/-0.1| 200+/-10| 148+/-7| 3| 60/81
UAT-30D(SD)| 5.0| 0.19+/-.01| 85+/-5| 63+/-4| 1| 20/27
UAT-40(S)(D), UAT-50(S)(D)| 5.6| 0.26+/-.01| 85+/-5| 63+/-4| 1| 20/27
UAT-60(S)(D)| 6.2| 0.35+/-.01| 85+/-5| 63+/-4| 1| 20/27
UAT-70(S)| 8.8| 0.60+/-.05| 110+/-5| 81+/-4| 2| 40/54
UAT-80| 12.0| 0.80+/-.05| 135+/-5| 100+/-4| 2| 40/54
UAT-90| 14.0| 0.90+/-.05| 150+/-5| 110+/-4| 3| 60/81
UAT-100| 21.5| 1.40+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UAT-130| 24.0| 1.40+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UAT-150| 31.5| 2.0+/-0.1| 290+/-10| 214+/-7| 4.5| 90/122
UAT-180| 39.0| 3.8+/-0.1| 320+/-10| 236+/-7| 4.5| 90/122
UAT-200| 81.5| 5.60+/-0.1| 320+/-10| 236+/-7| 4.5| 90/122
UBP-65| 8.0| 0.70+/-.05| 85+/-5| 63+/-4| 3| 60/81
UBP-T40 & T50| 5.6| 0.35 -.04| 85+/-5| 63+/-4| 1| 20/27
UBP-T60| 6.2| 0.45+/-.05| 85+/-5| 63+/-4| 1| 20/27
UDBP-T40 & T50| 5.6| 0.35 -.04| 85+/-5| 63+/-4| 1| 20/27
UDBP-T60| 6.2| 0.45+/-.05| 85+/-5| 63+/-4| 1| 20/27
UDBP-T70| 8.8| 0.70+/-.05| 110+/-5| 81+/-4| 2| 40/54
UDBP-TA40| 5.6| 0.26+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDBP-TA50| 5.6| 0.28+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDBP-TA60| 6.2| 0.37+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDBP-TA70(P)| 8.8| 0.60+/-.05| 110+/-5| 81+/-4| 2| 40/54
UBX-AF500Z, AF600Z| 8.9| 0.85+/-0.01| 85+/-5| 63+/-4| 1| 20/27
UBX-AF700Z| 12.0| 1.2+/-0.05| 110+/-5| 81+/-4| 2| 40/54
UBX-AF900Z| 15.3| 1.6 +/-0.05| 110+/-5| 81+/-4| 3| 60/81
UBX-T60, T60D| 8.9| 0.85+/-.05| 85+/-5| 63+/-4| 1| 20/27
UBX-T70, T70-RF8| 12.0| 0.85+/-.05| 110+/-5| 81+/-4| 1.5| 30/41
UBX-T80| 14.5| 1.5+/-0.05| 110+/-5| 81+/-4| 1.5| 30/41
UDP-A60MC| 5.6| 0.30+.05| 85+/-5| 63+/-4| 1.5| 30/41
UDP-A80MC| 8.8| 0.65+.05| 110+/-5| 81+/-4| 2| 40/54
UDP-TA40| 5.6| 0.28+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA40D| 5.6| 0.28+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA50| 5.6| 0.28+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA50D| 5.6| 0.28+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA55| 6.2| 0.37+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA55D| 6.2| 0.37+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA60| 6.2| 0.37+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UDP-TA60D| 6.2| 0.37+/-.01| 85+/-5| 63+/-4| 1.5| 30/41
UEP-50(D) & 50MC(D)| 5.5| 0.35+/-.05| 70+/-5| 52+/-4| 1| 20/27
UEP-60(D) & 60MC(D)| 6.8| 0.55+/-.05| 85+/-5| 63+/-4| 1| 20/27
UEP-70 & 70MC| 8.8| 0.65+/-.05| 110+/-5| 81+/-4| 2| 40/54
UEP-80 & 80MC| 14.0| 0.90+/-.05| 150+/-5| 110+/-4| 3| 60/81
UEP-100 & 100MC| 19| 1.50+/-.05| 185 /-10| 137+/-7| 3| 60/81
UL-30(D)| 5.0| 0.31+/-.01| 85+/-5| 63+/-4| |
---|---|---|---|---|---|---
UL-40(D), UL-40A(D)MC| 5.0| 0.35+/-.01| 85+/-5| 63+/-4| 1| 20/27
UL-50(S)(D) & 50(D)MC, UL-40(D)MC, UL-50A(D)MC| 5.0| 0.45+/-.05| 85+/-5| 63+/-4| 1| 20/27
UL-60(S)(D), 60MC, 60AMC| 6.8| 0.55+/-.05| 85+/-5| 63+/-4| 1| 20/27
UL-70, UL-70MC, 70AMC| 8.0| 0.65+/-.05| 110+/-5| 81+/-4| 2| 40/54
UL-80| 14.0| 0.80+/-.05| 110+/-5| 81+/-4| 2| 40/54
UL-90, UL-90MC, 90AMC, 900AMC| 14.0| 0.95+/-.05| 150+/-5| 110+/-4| 3| 60/81
UL-100| 19| 1.50+/-.05| 185+/-10| 137+/-7| 3| 60/81
UL-100MC, 100AMC| 21.5| 1.60+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UL-130| 27.0| 1.70+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UL-130MC, 130AMC| 24.0| 1.60+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UL-150| 36.6| 2.60+/-0.1| 200+/-10| 148+/-7| 3| 60/81
ULT-30 (D)(S)| 5.0| 0.30+/-.01| 85+/-5| 63+/-4| 1| 20/27
ULT-40(S)(D) & 50(S)(D)(C),| 5.6| 0.35 -.04| 85+/-5| 63+/-4| 1| 20/27
ULT-60(S)(D)(C)| 6.2| 0.45+/-.05| 85+/-5| 63+/-4| 1| 20/27
ULT-70(S)(C)(CH)| 8.8| 0.70+/-.05| 110+/-5| 81+/-4| 2| 40/54
ULT-80| 12.0| 0.85+/-.05| 110+/-5| 81+/-4| 2| 40/54
ULT-90| 14.0| 1.00+/-.05| 150+/-5| 110+/-4| 3| 60/81
ULT-100| 21.5| 1.60+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ULT-130| 24.0| 1.60+/-0.1| 185+/-10| 137+/-7| 3| 60/81
ULT-150| 31.5| 2.20+/-0.1| 200+/-10| 148+/-7| 3.5| 70/95
ULT-180| 39.0| 3.30+/-0.1| 260+/-10| 192+/-7| 4| 80/108
UX-450(S)(D)| 5.0| 0.50+/-.05| 70+/-5| 52+/-4| |
UX-500(S)(D)(C)| 5.0| 0.50+/-.05| 70+/-5| 52+/-4| |
UX-612(S)(D)(C)(A)| 6.2| 0.65+/-.05| 85+/-5| 63+/-4| |
UX-622(D)| 6.2| 0.65+/-.05| 85+/-5| 63+/-4| |
UX-700(S)(D)(C) & 80EC| 8.8| 0.80+/-0.1| 110+/-5| 81+/-4| 2| 40/54
UX-800(S)(C) & ST800| 12.0| 0.80+/-0.1| 135+/-5| 100+/-4| 2| 40/54
UX-900(S)(C) & 120EC| 14.0| 0.95+/-0.1| 150+/-5| 110+/-4| 3| 60/81
UX-1000(S)(C) & 130EC| 19.0| 1.50+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UX-1300(S), T1300 & TL1300| 24.0| 1.80+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UX-1400| 31.5| 2.00+/-0.1| 200+/-10| 148+/-7| 3.5| 70/95
UX-1620| 33.5| 2.20+/-0.1| 200+/-10| 148+/-7| 4| 80/108
UX-T700, T700L & TL700| 8.8| 0.70+/-.05| 110+/-5| 81+/-4| 2| 40/54
UX-T800 & TL800| 12.0| 0.80+/-.05| 135+/-5| 100+/-4| 2| 40/54
UX-T900 & TL900| 14.0| 0.95+/-.05| 150+/-5| 110+/-4| 3| 60/81
UX-T1000 & TL1000| 19.0| 1.40+/-0.1| 185+/-10| 137+/-7| 3| 60/81
UX-T1400 & TL1400| 31.5| 1.90+/-0.1| 200+/-10| 148+/-7| 3.5| 70/95
UX-T1620 & TL1620| 33.5| 2.10+/-0.1| 200+/-10| 148+/-7| 4| 80/108
UXR-1820(MC)| 48.0| 3.50+/-0.1| 260+/-10| 192+/-7| 4| 80/108
UXR-2000(S)(MC)| 84.0| 7.00+/-0.2| 300+/-10| 221+/-7| 4| 80/108
UXR-2400S(MC)| 105.0| 11.00+/-0.2| 650+/-10| 480+/-7| 5| 100/74
UXR-3000S| 185.0| 14.00+/-0.2| 700+/-10| 517+/-7| 5| 100/74
UXR-T1820 & TL1820| 48.0| 3.50+/-0.1| 260+/-10| 192+/-7| 4| 80/108
UXR-T2000 & TL2000| 84.0| 6.00+/-0.1| 300+/-10| 221+/-7| 4| 80/108
UXR-T2400S| 105.0| 10.50+/-0.2| 650+/-10| 480+/-7| 5| 100/74
UXR-T3000S| 185.0| 13.50+/-0.2| 700+/-10| 517+/-7| 5| 100/74

Customers Support

CORPORATE HEADQUARTERS
10000 SE Pine Street
Portland, Oregon 97216
Phone: (503) 254-6600
Toll Free: 1-800-852-1368

AIMCO CORPORATION DE MEXICO SA DE CV
Ave. Cristobal Colon 14529
Chihuahua, Chihuahua. 31125
Mexico
Phone: (01-614) 380-1010
Fax: (01-614) 380-1019

LIT-MAN310 Rev. 07/12/23
Printed in USA ©2023 AIMCO

WWW.AIMCO-GLOBAL.COM

10000 SE Pine St., Portland OR 97216
800-852-1368
Fax 800-582-9015
www.aimco-global.com

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

AIMCO User Manuals

AIMCO A-50A-0 Acra Feed Screw Presenters Owner’s Manual
AIMCO
AIMCO Gen IV Controller Electronic Industry User Guide
AIMCO
AIMCO VC-101-2(A) Vacuum Tank User Manual
AIMCO
AIMCO Gen III 5000 In-Line Nutrunner Instruction Manual
AIMCO
AIMCO LIT-MAN350 UFT Series Joint Simulator Instruction Manual
AIMCO
AIMCO AcraDyne Gen IV ACE Controller Firmware Instructions
AIMCO
AIMCO AcraDyne Gen IV Controller Instructions
AIMCO
AIMCO UAT-30D UAT Series Pistol Grip Auto Shut Off Pulse Tool User Manual
AIMCO
AIMCO LIT-MAN177 Gen IV Controller Instructions
AIMCO
AIMCO AEP4A771200B AcraDyne High-Torque DC Nutrunner User Manual
AIMCO
AIMCO XML Gen IV Controller Instructions
AIMCO
AIMCO ULT Series ULT-30D Pulse Tools Instruction Manual
AIMCO
AIMCO UBX-T Auto Shut-Off Battery Pulse Tools User Manual
AIMCO
AIMCO AT320HT High-Torque Tools For Critical Bolting User Manual
AIMCO
AIMCO Anybus Gen IV Controller Instructions
AIMCO
AIMCO Global A-50 Screw Presenters Instruction Manual
AIMCO Global
AIMCO P02 High Capability Tool Instruction Manual
AIMCO
AIMCO Gen 4 HT Series High Torque DC Nutrunners Instruction Manual
AIMCO
AIMCO AcraDyne Gen IV iEC Controller Instruction Manual
AIMCO
AIMCO DWL-B Wireless Receiver Instruction Manual
AIMCO

Related Manuals

Ability VS68200 AI-Eye 8M Fixed Lens Dome Network Camera User Guide
Ability
Sharper Image OWN ZONE Wireless Rechargeable TV Headphones-Complete Features\Instruction Manual
SHAREP IMAGE
Z-Lite 337MP-MB Burren 1 Light 9 inch Matte Black Mini Pendant Ceiling Light Instruction Manual
Z-Lite
brinno BCC200 TimeLapse Construction Camera Pro User Guide
brinno
ATEN CS782DP 2-Port USB DisplayPort KVM Switch User Manual
Aten
OMRON HEM-RML31-B Wide-Range D-Ring Cuff User Manual
Omron
Sharkoon S25-V Introduces Minimalistic Case Owner’s Manual
sharkoon
FerdY 47 Bali Acrylic Freestanding Bathtub Installation Guide
FerdY
Lightcloud SENSE-PIR-W-LCB Wireless Occupancy Sensor User Manual
Lightcloud
stryker 5212 iBed Locator Installation Guide
stryker
Dwyer Series GSTA Carbon Monoxide-Nitrogen Dioxide Gas Transmitters Instruction Manual
Dwyer
Vorago KB-506 Gaming Keyboard User Guide
Vorago
FP PostBase Mini Postage Meter Installation Guide
FP
ELINZ TPMS4TYRE Car Auto Wireless Digital TPMS Tire Tyre Pressure Monitoring System User Manual
ELInZ
Ideal Standard BD338 Ceraplan Kitchen Mixer Instructions
Ideal Standard
INITIO B087C3XFVT 300ML Water Flosser User Manual
INITIO
KidKraft Play System User Manual
KidKraft
DS18 DDX6.9CP 6.9-Inch Double Din Multimedia Receiver Owner’s Manual
DS18
CANYON CND-GPW7 4 in 1 Wireless Controller User Guide
CANYON
LTECH B5DMX4AS DMX Bluetooth Constant Voltage LED Controller User Manual
LTECH
My Weigh iBalance i311 Digital Scale User Manual
My Weigh
KEMIMOTO B1406-04101BK Universal Golf Cart Rear View Mirror Instruction Manual
KEMIMOTO
element E4SW5518RKU Roku TV User Guide
Element
DENON DJ MC4000 Serato DJ Controller User Guide
DENON DJ
GLOBAL INDUSTRIAL 412663 TEP Bench Scale LCD Display Installation Guide
GLOBAL INDUSTRIAL
FosPower Kids Headphones with LED Light Headphones-Complete Features\Instruction Manual
FOSPOWER
dellonda DH16 Black Electric Adjustable Desk Frame Instruction Manual
dellonda
DEXIBELL S10L VIVO Digital Piano User Guide
DEXIBELL
snom M500 PRO Wireless Family Instruction Manual
snom
Tiny Love 4-in-1 Here I Grow Mobile Activity Center User Guide
Tiny Love
Contact Us   Privacy Policy   4.401ms