HINKLEY 28920HB-LL LED Wall Mount Instruction Manual

June 16, 2024
HINKLEY

HINKLEY 28920HB-LL LED Wall Mount

Product Information

Specifications

  • Model: HINKLEY
  • Part Number: 1 3 2 4 5 6 7
  • Installation Type: Glass Installation
  • Language Options: English, Spanish, French

Product Usage Instructions

Installation

  1. Remove screws (1) to release the backplate (3) from the mounting plate(5).
  2. Secure mounting plate (4) to junction box (2) using screws (4)not provided.
  3. Use wall anchors (6) and machine screws (7) to install the backplate on the wall.
  4. Make wiring connections using IS-18 on the next page.
  5. Secure backplate (3) to mounting plate (5) using the previously removed screws (1).

Glass Installation

  1. Lamp fixture with appropriate bulb (8).
  2. Use hex nut (12) and flat washer (11) to install the glass (10)on the threaded pipe (9).
  3. Install the coupler (14) and cap (13) on the pipe (9).
  4. Install the nipple (17) on the coupler (14).
  5. Use final (18) to install the pipe (15) onto the nipple(17).
  6. Use screw (16) to install the pipe (15) on the backplate.
  7. The fixture can now be powered on.

Note: For outdoor use, please ensure the socket is installed facing downward.

Caulking Instructions

After securing fixture to the wall, it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides with a good quality waterproof caulk or silicone sealant (NOT INCLUDED). See Drawing 1 for reference. Bead of caulk to seal the gap. Use a caulking gun for application.

Wiring and Grounding Instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

FAQ

Q: What languages are supported by the product?

A: The product supports English, Spanish, and French.

Q: Can the product be used for outdoor installations?

A: Yes, the product can be used for outdoor installations. Please ensure the socket is installed facing downward.

Q: Is the waterproof caulk or silicone sealant included with the product?

A: No, the waterproof caulk or silicone sealant is not included with the product.

Assembly Instructions

  • Find a clear area in which you can work.
  • Unpack the fixture and glass from the carton.
  • Carefully review instructions before assembly.
  1. Remove screws (1) to release backplate (3) from mounting plate (5)
  2. Secure mounting plate (4) to junction box (2) using screws (4) not provided
  3. Use wall anchors (6) and machine screws (7) to install the backplate on the wall.
  4. Make wiring connections using IS-18 on the next page
  5. Secure backplate (3) to mounting plate (5) using the previously removed screws (1)

SAFETY WARNING
READ WIRING AND GROUNDING INSTRUC-TIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.

  1. Lamp fixture with appropriate bulb (8)
  2. Use hex nut (12) and flat washer (11) to install the glass (10) on the threaded pipe (9).
  3. Install the coupler (14) and cap (13) on the pipe (9).
  4. Install the nipple (17) on the coupler (14).
  5. Use final (18) to install the pipe (15) onto the nipple (17).
  6. Use screw (16) to install the pipe (15) on the backplate.
  7. The fixture can now be powered on

Note: For outdoor use, please ensure the socket is installed facing downward

IS200 Caulking Instructions

  • After securing fixture to the wall it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides, with a good quality waterproof caulk or silicone sealant (NOT INCLUDED) – see Drawing 1.

  • After securing fixture in place it is recommended that the gap between the mounting top and fixture base be sealed with any good quality waterproof caulk or silicone sealant (not included). It is also recommended that a small bead of caulk or sealant be put under the ball knobs used to mount fixture – see Drawing 2.

I.S. 18 wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Wiring instructions

  1. Indoor Fixtures
  2. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
  3. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
  4. Please refer to the grounding instructions below to complete all electrical connections
  5. Outdoor Fixtures
  6. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
  7. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
  8. Cover the open end of connectors with silicone sealant to form a watertight seal.
  9. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform especially.
  10. Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions

  1. Flush Mount Fixtures
    For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
    Note: On straps for screw supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

  2. Chain Hung Fixtures
    Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

  3. Post-Mount Fixtures
    Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

H I N K L E Y 33000 Pin Oak Parkway, Avon Lake, OH 44012 8 00.446.5539 / 440.653.5500 hinkley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals