BLUSTREAM UEX50B-KIT USB 2.0 Extender Set User Guide
- June 4, 2024
- BLUSTREAM
Table of Contents
BLUSTREAM UEX50B-KIT USB 2.0 Extender Set
Introduction
Our UEX50B-KIT delivers USB 2.0 extension up to 50m over a single CAT cable while allowing up to 4 USB devices to be connected to a single USB host. Supports transmission data bandwidth up to 480Mbps, backward compatible with USB 1.1 devices.
FEATURES
- Extends USB up to a distance of 50m over a single CAT cable
- Supports USB 2.0 signal extension
- Backward compatible with USB 1.1 devices
- Transmitted data bandwidth up to 480Mbps
- 1x USB-B on Receiver for connection to host device
- 4x USB-A hub on Transmitter for connection to devices
- USB-A ports 1-2 support 5V1A, USB-A ports 3-4 support 5V500mA
- Simple plug and play, no driver installation or setup required.
Signal distribution length is subject to the length of the device and host USB cables and CAT cable type.
TX Panel Descriptions
- CAT Cable Connection – Connect to CAT cable and to UEX50B-RX
- 12V/2A DC Power Input screw type connector
- Power Status Indicator
- 1A USB Device Connection – USB A connection to connect to high current (up to 1A) USB devices
- 500mA USB Device Connection – USB A connection to connect to low current (up to 500mA) USB devices.
RX Panel Descriptions
- 6 CAT Cable Connection – Connect to CAT cable and to UEX50B-TX
- 7 Power Switch – Select between powering the Receiver from the Transmitter (TX) or Host PC that USB is connected to
- 8 USB Host Connection – USB B connection to connect to PC
- 9 Power Status Indicator
Device Cabling
It is important that interconnecting CAT cable between the Transmitter and Receiver is terminated using straight the correct RJ45 pin configuration. The CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable. Please ensure that the USB cabling used with this product is within specifications for both the distance and maximum / expected data rate transfer of the equipment in use. Exceeding distances, or using cabling not suitable for the data transfer, may stop the UEX50B-KIT from working properly. It is recommended to keep the USB cabling on either side of the UEX50B-KIT to a minimum, using the range of the equipment to run the distance over the CAT cable infrastructure.
Specifications
UEX50B-TX
- CAT Connectors: 1 x RJ45 connector
- USB Port: 4 x USB Type-A
- Casing Dimensions (W x D x H): 84 x 60 x 23.5mm
- Power Supply: 12V/2A DC, screw-type connector
UEX50B-KIT
- Box Dimensions (W x D x H): 156 x 82 x 121mm
- Shipping Weight: 0.5kg
- Operating Temperature: 32°F to 104°F (-5°C to +55°C)
- Storage Temperature: -4°F to 140°F (-25°C to +70°C)
UEX50B-RX
- CAT Connectors: 1 x RJ45 connector
- USB Port: 1 x USB Type-B
- Casing Dimensions (W x D x H): 84 x 60 x 23.5mm
- Power Supply: 12V/2A DC, screw-type connector
Package Contents
- 1 x UEX50B-TX Transmitter
- 1 x UEX50B-RX Receiver
- 1 x 12V/2A DC Power Supply
- 1 x USB A to B cable (1m)
- 2 x Mounting Bracket Sets
- 1 x Quick Reference Guide
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate.
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
Certifications
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed of with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmentally safe
recycling.
Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk. www.blustream- us.com. www.blustream.com.au. www.blustream.co.uk.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>